Disk Enclosures
1748252 Members
4036 Online
108760 Solutions
New Discussion юеВ

Re: New LUN on MSA1000, An alternate path on HPUX?

 
Juan Manuel L├│pez
Valued Contributor

New LUN on MSA1000, An alternate path on HPUX?

Hi all.
I have added 4 new disks to my msa1000 enclosure.
I have created a new LUN raid5 and without more configuration I have discovered the new disk in HPUX machine.
The problem is that the new disk is recognized like an alternate path.
What I have to do to see the new disk like a diferent disk ?.

I show the MSA Details:

CLI> show tech_support

CLI> show version
Firmware version: 4.38 build 287
Hardware Revision: 7
Internal EMU Rev: 1.86 (SGM050506W)

Global Parameters:
System Name:
Rebuild Priority: medium
Expand Priority: medium

Total Cache: 512MB
50% Read Cache: 256MB
50% Write Cache: 256MB

Temperature:
EMU: 25 Celsius, 77 Fahrenheit
PS1: 35 Celsius, 95 Fahrenheit
PS2: 38 Celsius, 100 Fahrenheit
FIBRE BAY: 40 Celsius, 104 Fahrenheit

CLI> show acl

ACL is disabled. To enable ACL use 'add acl'.

CLI> show connections

Connection Name: TSPU01
Host WWNN = 50060B00-002D54C5
Host WWPN = 50060B00-002D54C4
Profile Name = HP
Unit Offset = 0
Controller 1 Port 1 Status = Online

CLI> show disks
Disk List: (box,bay) (bus,ID) Size Units
Disk101 (1,01) (0,00) 146.8GB 0
Disk102 (1,02) (0,01) 146.8GB 0
Disk103 (1,03) (0,02) 146.8GB 0
Disk104 (1,04) (0,03) 146.8GB 0
Disk105 (1,05) (0,04) 146.8GB 0
Disk106 (1,06) (0,05) 146.8GB 0
Disk107 (1,07) (0,08) 146.8GB 0
Disk108 (1,08) (1,00) 146.8GB 0
Disk109 (1,09) (1,01) 300.0GB 1
Disk110 (1,10) (1,02) 300.0GB 1
Disk111 (1,11) (1,03) 300.0GB 1
Disk112 (1,12) (1,04) 300.0GB 1

CLI> show units

Unit 0:
In PDLA mode, Unit 0 is Lun 1; In VSA mode, Unit 0 is Lun 0.
Unit Identifier : SCPOOL
Device Identifier : 600805F3-00135D30-00000000-04820002
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Parity Init Status: Complete
8 Data Disk(s) used by lun 0:
Disk101: Box 1, Bay 01, (SCSI bus 0, SCSI id 0)
Disk102: Box 1, Bay 02, (SCSI bus 0, SCSI id 1)
Disk103: Box 1, Bay 03, (SCSI bus 0, SCSI id 2)
Disk104: Box 1, Bay 04, (SCSI bus 0, SCSI id 3)
Disk105: Box 1, Bay 05, (SCSI bus 0, SCSI id 4)
Disk106: Box 1, Bay 06, (SCSI bus 0, SCSI id 5)
Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8)
Disk108: Box 1, Bay 08, (SCSI bus 1, SCSI id 0)
Spare Disk(s) used by lun 0:
No spare drive is designated.
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (Raid 5)
stripe_size=16kB
Logical Volume Capacity : 980,090MB

Unit 1:
In PDLA mode, Unit 1 is Lun 2; In VSA mode, Unit 1 is Lun 1.
Unit Identifier : NCPOOL
Device Identifier : 600805F3-00135D30-00000000-7F110003
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Parity Init Status: waiting for first write
4 Data Disk(s) used by lun 1:
Disk109: Box 1, Bay 09, (SCSI bus 1, SCSI id 1)
Disk110: Box 1, Bay 10, (SCSI bus 1, SCSI id 2)
Disk111: Box 1, Bay 11, (SCSI bus 1, SCSI id 3)
Disk112: Box 1, Bay 12, (SCSI bus 1, SCSI id 4)
Spare Disk(s) used by lun 1:
No spare drive is designated.
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (Raid 5)
stripe_size=16kB
Logical Volume Capacity : 858,300MB

CLI> show this_controller
Controller:
MSA1000(c) Compaq P56350GX3R80WA Software 4.38 Build 287 Hardware 7
Controller Identifier:
NODE_ID = 500805F3-00135D30
SCSI_VERSION = SCSI-3
Supported Redundancy Mode: Active/Standby
Current Redundancy Mode: Not Redundant (No Failure)
Device Port SCSI address 6
Terminal speed for the CLI is set to 19200.
Host Port_1:
REPORTED PORT_ID 500805F3-00135D31
PORT_1_TOPOLOGY = F_Port
Cache:
256 megabyte read cache 256 megabyte write cache Version 2
Cache is GOOD, and Cache is enabled.
No unflushed data in cache
Battery:
Module #1 is fully charged and turned off.
Module #2 is fully charged and turned off.

CLI> show other_controller
Other controller is not present or fully started.

CLI>

AND HOW THE O.S see THIS DISK:

disk 88 0/12/0/0.1.0.0.0.0.0 sdisk CLAIMED DEVICE COMPAQ MSA1000 VOLUME
/dev/dsk/c13t0d0 /dev/rdsk/c13t0d0

disk 71 0/12/0/0.1.0.0.0.0.1 sdisk CLAIMED DEVICE COMPAQ MSA1000 VOLUME
/dev/dsk/c13t0d1 /dev/rdsk/c13t0d1

Ussing SAM, I see disk 71 like alternate path of disk 88.
Any suggestion ?

Juanma.
I would like to be lie on a beautiful beach spending my life doing nothing, so someboby has to make this job.
2 REPLIES 2
Juan Manuel L├│pez
Valued Contributor

Re: New LUN on MSA1000, An alternate path on HPUX?

I have found a post with the same problem.
I also create a new vg and lv with the second lun, so SAM does not see this 2nd disk and see it like alternate disk of first disk of msa 1000.

Any suggestion ?

Thanks in advance
Juanma.
I would like to be lie on a beautiful beach spending my life doing nothing, so someboby has to make this job.
Juan Manuel L├│pez
Valued Contributor

Re: New LUN on MSA1000, An alternate path on HPUX?

Sorry, I had forget the link.

http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=891551
I would like to be lie on a beautiful beach spending my life doing nothing, so someboby has to make this job.