- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: eventID 24606 and eventID 11
Disk Enclosures
1752679
Members
5254
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-07-2011 01:07 PM
тАО06-07-2011 01:07 PM
eventID 24606 and eventID 11
I found a problem in the event viewer of windows that is installed in my HP DL360 G6 . Thinking that he was referring to the alert "Disk Fault" i have changed the disk on "bus 0 and ID 6" as stated in the error , but the problem is still reported . In this server there are 2 partions one in RAID1 with 72 Gb X two disk and one with RAID0 for CACHE DATA with 146 Gb X four disk . So we have 6 to 8 allocations occupied . Here's the error alert :
event 24606 Source:Cissesrv
Logical drive 2 configured on array controller P410i [Embedded] returned a fatal error during a read/write request from/to the volume.
Logical block address 59663968, block count 48 and command 32 were taken from the failed logical I/O request.
Array controller P410i [Embedded] is also reporting that the last physical drive to report a fatal error condition (associated with this logical request), is located on bus 0 and ID 6.
eventid 11 Source Disk
The driver detected a controller error on \Device\Harddisk1\DR1.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
event 24606 Source:Cissesrv
Logical drive 2 configured on array controller P410i [Embedded] returned a fatal error during a read/write request from/to the volume.
Logical block address 59663968, block count 48 and command 32 were taken from the failed logical I/O request.
Array controller P410i [Embedded] is also reporting that the last physical drive to report a fatal error condition (associated with this logical request), is located on bus 0 and ID 6.
eventid 11 Source Disk
The driver detected a controller error on \Device\Harddisk1\DR1.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-07-2011 01:10 PM
тАО06-07-2011 01:10 PM
Re: eventID 24606 and eventID 11
I would add that the "Array Diagnostic Utility" returns no errors .
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2011 05:22 AM
тАО06-08-2011 05:22 AM
Re: eventID 24606 and eventID 11
So you got a RAID 0 (Zero(Logical drive 2?)).
Then you get a disk failure (possible in the RAID 0).
Now that logical drive is, failed.
You have replaced the failed disk.
Windows can't read/write to the failed RAID 0.
A disk failure in a RAID 0, is fatal. So far all is as expected.
I don't know how much you have to do, to get a new operational RAID 0. And oprational disk in windows.
My guess is.
1. Delete the failed disk from windows disk manager.
2. Delete the RAID 0 on the array controller.
3. Create new RAID
4. do whatever you have to do to get a new disk in windows disk manager.
BR
/jag
Then you get a disk failure (possible in the RAID 0).
Now that logical drive is, failed.
You have replaced the failed disk.
Windows can't read/write to the failed RAID 0.
A disk failure in a RAID 0, is fatal. So far all is as expected.
I don't know how much you have to do, to get a new operational RAID 0. And oprational disk in windows.
My guess is.
1. Delete the failed disk from windows disk manager.
2. Delete the RAID 0 on the array controller.
3. Create new RAID
4. do whatever you have to do to get a new disk in windows disk manager.
BR
/jag
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2011 05:44 AM
тАО06-08-2011 05:44 AM
Re: eventID 24606 and eventID 11
Although this error Windows signals the applications work correctly. But maybe only because that part of the disc has not yet been used?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP