Operating System - Tru64 Unix
1748169 Members
4139 Online
108758 Solutions
New Discussion юеВ

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

 
peynet
Occasional Advisor

DS20E KZPAC and TRU64 4.0F install and boot problem

Hello,

My Config is :

DS20E with last firmware update 7.3 passed
KZPAC with firmware 2.7 passed
Disk drive Compaq 18,2 G Ultra2 SCSI
Also tested with
Disk drive Compaq 36 G Ultra320 SCSI

Only one disk configure DRA0 18 Go (JBOD

On my DS20E when booting to install from CD ROM after a while I got the message :


...
Initializing xcr0, please waitтАж
Xcr0 at pci1 slot 9
Xcr_logger : XCR_ERROR packet
Xcr_logger : cntrl 0 unit 0
Re_getdrive
Cmd should always return good status
Hard error detected
Active XCR_COM at time of error
Xcr_logger : XRC_ERROR packet
Xcr_logger : cntrl 0 unit 0
Re_getdrive
Cmd memory lost
Possible software problem тАУ impossible Cond detected
Active XCR_COM at time of error

The Installation continue I can select the drive re0 and install the system
but on the next reboot I have


bootdevice_parser : unknown protocol name 'RAID'
setconf : Bootdevice_parser failed to translate bootdevice RAID 1 9 0 0 0 0 0
Panic (CPU0) setconf:Bootdevice_parser failed

If someone have an idea
Thanks

Eric
10 REPLIES 10
cnb
Honored Contributor

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

cnb
Honored Contributor

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

peynet
Occasional Advisor

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

Thanks,

I have split my disk to 2x18 Go logical drives of course

I have also read the release notes before posting this thread

I have had configure (in the past) a KZPAC with same drives and it works !!
But I Do not remember if the server was a DS20E

Eric

Rob Leadbeater
Honored Contributor

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

Hi Eric,

I seem to recall a KZPAC that was also returning XCR_ERROR messages and impossible Cond detected.

This turned out to be a faulty card.

If your problems persist, replace the KZPAC.

Regards,

Rob
peynet
Occasional Advisor

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

Rob,
I already tried with 4 cards 3 chanels and 1 card sigle chanel
The problem is the same

Eric
marlene lam
Frequent Visitor

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

when you tried a new KZPAC card , was it also installed in the same slot ?
In the original post I see slot 9, and that follows the rules:
http://h18002.www1.hp.com/alphaserver/options/asds20e/asds20e_All_options_sorted.html#OptListHead

http://h18002.www1.hp.com/alphaserver/options/asds20e/asds20e___-kzpac-ca.html


Restricted to PCI slots in HOSE 1.

Tapes and CD-ROMs not supported.

Internal drives not supported in the 4 slot disk storage backplane.


Lastly, you can try split the RAID disks into 2 JBODS and try each one at a time

- regards,
Marlene
peynet
Occasional Advisor

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

I have tried this KZPAC on a DS10 the problem is the same
The only way I can make this card working (both on DS10 or DS20E) is :
Create a drive dra0
Create a drive dra1
Install OpenVMS on dra0
Install TRU64 4.0F on dra1
Then TRU64 40F boot !!!!!!
When I reinit the card recreate drive and reinstall only TRU64 4.0F it doesn't work

So strange isn't it

Eric
Rob Leadbeater
Honored Contributor

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

Hi,

Looking again at the original error message referring to setconf and bootdevice_parser, it would appear that the system is having difficulty setting the various boot environment variables during the installation.

Can you post the output of "show boot*" and "show config"

Cheers,
Rob
peynet
Occasional Advisor

Re: DS20E KZPAC and TRU64 4.0F install and boot problem

Rob

here is sh boot*

boot_dev dra0.0.0.9.1
boot_file
boot_osflags A
boot_reset OFF
bootbios
bootdef_dev dra0.0.0.9.1
booted_dev dra0.0.0.9.1
booted_file genvmunix
booted_osflags A

and the sho conf

Eric

COMPAQ AlphaServer DS20E 833 MHz

SRM Console: V7.3-1
PALcode: OpenVMS PALcode V1.98-79, Tru64 UNIX PALcode V1.92-74

Processors
CPU 0 Alpha EV68A pass 2.2 833 MHz SROM Revision: V1.17.44
Bcache size: 8 MB

Core Logic
Cchip DECchip 21272-CA Rev 2.1
Dchip DECchip 21272-DA Rev 2.0
Pchip 0 DECchip 21272-EA Rev 2.2
Pchip 1 DECchip 21272-EA Rev 2.2

TIG Rev 4.22
Arbiter Rev 2.16 (0x1)

MEMORY

Array # Size Base Addr
------- ---------- ---------
0 1024 MB 000000000
2 1024 MB 040000000

Total Bad Pages = 0
Total Good Memory = 2048 MBytes


PCI Hose 00
Bus 00 Slot 05/0: Cypress 82C693
Bridge to Bus 1, ISA
Bus 00 Slot 05/1: Cypress 82C693 IDE
dqa.0.0.105.0
dqa0.0.0.105.0 CD-224E
Bus 00 Slot 05/2: Cypress 82C693 IDE
dqb.0.1.205.0
Bus 00 Slot 05/3: Cypress 82C693 USB
usba0.0.0.305.0
Bus 00 Slot 06/0: Adaptec AIC-7895
pkb0.7.0.6.0 SCSI Bus ID 7
Bus 00 Slot 06/1: Adaptec AIC-7895
pkc0.7.0.106.0 SCSI Bus ID 7

PCI Hose 01
Bus 00 Slot 08: QLogic ISP10x0
pka0.7.0.8.1 SCSI Bus ID 7
Bus 00 Slot 09: Mylex DAC960
dra.0.0.9.1 dra0.0.0.9.1 1 Member JBOD
dra1.0.0.9.1 1 Member JBOD


ISA
Slot Device Name Type Enabled BaseAddr IRQ DMA
0
0 MOUSE Embedded Yes 60 12
1 KBD Embedded Yes 60 1
2 COM1 Embedded Yes 3f8 4
3 COM2 Embedded Yes 2f8 3
4 LPT1 Embedded Yes 3bc 7
5 FLOPPY Embedded Yes 3f0 6 2