- Community Home
- >
- Storage
- >
- Legacy
- >
- Storage Software
- >
- Storage Controller testing
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-04-2015 08:49 AM
05-04-2015 08:49 AM
Hi,
I need some details to perform some testing. I have been asked to configure the storage system for our e-commerse software for RAID1 and ensure the storage controller works as expected.
I have gone through hpssacli & hpssascripting. I have cook book PDF. I understand the concept to configure RAID1. Now i want to test whenther storage controller is working as expected. RAID 1 means 2 identical data copied in 2 hard drives.
I want to test following scenarios;
a) Write some data on RAID1 configuration. Make one of the hard drive to fail and ensure the controller will get the data from the different drive.
b) Configure the cache and ensure the cache is having some write data. Force the cache volume to fail and check the data will not be lost.
How can i test above scenarios. I am sitting in a remote location and i don't have any physical access to the storage system. Keeping this thing in mind how can i test above scenarios?
I am new to the storage domain, execuse me if i am asking silly questions. But i badly need support on it.
Thanks in advance.
Regds,
satya
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-04-2015 10:02 AM
05-04-2015 10:02 AM
Re: Storage Controller testing
What kind of storage do you have?
Without physical access, I'm not sure how successful you'll be.
This testing sounds more like something a vendor would do, not an end user.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-04-2015 12:58 PM
05-04-2015 12:58 PM
Re: Storage Controller testing
Infrastructure physical set up is configured in a remote location by a service vendor. So i don't have much information. But i have access to the controller and able to run the commands to configure.
I ran "ctrl show all " command and i got the following information
Smart Array P440ar in Slot 0 (Embedded) .
Not sure if this information is sufficient to direct me?
Is it possible to disable or enable the hard drives using the controller. If it is possible, then i can simulate my test and get the result....
If you think physical access is mandatory then confirm me, so that i can raise my hands and try to figure out to get physical help.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-04-2015 01:27 PM - edited 05-04-2015 01:31 PM
05-04-2015 01:27 PM - edited 05-04-2015 01:31 PM
SolutionSuch an internal smart array controller is just a standard. Up to year 2005 HP has shipped 10 million proliants already.
(see http://www8.hp.com/us/en/hp-news/press-release.html?id=171397#.VUfVU5PQrHU )
In 2014
...HP shipped more than 4 servers each minute in the second calendar quarter 2014....
( see http://www8.hp.com/de/de/solutions/business-perspective-article.html?compURI=1103378#.VUfUsZPQrHU )
Millions of customers have tested the controllers in every possible way, so I would just trust a mirror will work as expected and I would not start pulling disks just for another "testing" ... ;-)
If you talk about smart caching, this is a read only cache, see http://h18004.www1.hp.com/products/servers/proliantstorage/arraycontrollers/smartcache/
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-04-2015 11:15 PM
05-04-2015 11:15 PM
Re: Storage Controller testing
Thanks a lot for your response and reference links.
Yes i accept your point. I will try to convince my management to skip this testing.