- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: PX_NOPV on lvdisplay
Operating System - HP-UX
1752571
Members
5006
Online
108788
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-20-2007 08:03 AM
07-20-2007 08:03 AM
PX_NOPV on lvdisplay
Hi peer
i lvextended an lvol (from a PVG, mirroring the lvol to another PVG).
the command is still in execution but the lvdisplay gives PX_NOPV oon description of disks of mirrored copy of ALL physical extent.
Any suggestion
The VG is a cluster VG, and anoter hosts as a different pvg definition of such vg.
Thanks and regards
RV
i lvextended an lvol (from a PVG, mirroring the lvol to another PVG).
the command is still in execution but the lvdisplay gives PX_NOPV oon description of disks of mirrored copy of ALL physical extent.
Any suggestion
The VG is a cluster VG, and anoter hosts as a different pvg definition of such vg.
Thanks and regards
RV
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-21-2007 07:27 PM
07-21-2007 07:27 PM
Re: PX_NOPV on lvdisplay
Hello,
It is obvious that some command failure has
left the logical volume in state where extents are not assigned to a physical volume correctly.
There is a nice Technical Knowledge Base document ULVMKBRC00009684 that describes
your problem .
Several possibilities:
a) Check your patches. For example,
PHKL_31500 addresses it for HP-UX 11.23.
PHKL_35970 for HP-UX 11.11.
b) Reduce the logical volume and "rebuild
the mirroring"
lvreduce -m 0 ....
Regards,
VK2COT
It is obvious that some command failure has
left the logical volume in state where extents are not assigned to a physical volume correctly.
There is a nice Technical Knowledge Base document ULVMKBRC00009684 that describes
your problem .
Several possibilities:
a) Check your patches. For example,
PHKL_31500 addresses it for HP-UX 11.23.
PHKL_35970 for HP-UX 11.11.
b) Reduce the logical volume and "rebuild
the mirroring"
lvreduce -m 0 ....
Regards,
VK2COT
VK2COT - Dusan Baljevic
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP