Operating System - HP-UX
1748112 Members
3481 Online
108758 Solutions
New Discussion юеВ

Re: rp3440 connected to msa30 cannot activate vg

 
Gabriel Madoz
Frequent Advisor

Re: rp3440 connected to msa30 cannot activate vg

Ok, we know how to solve it but the question is WHY is it happening.... From the logs I attached, can you see any info to address it on the future? thanks
Gabriel Madoz
Torsten.
Acclaimed Contributor

Re: rp3440 connected to msa30 cannot activate vg

I don't know why you replaced both disks, but since you replaced both disks in this RAID all the data is gone as expected.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Gabriel Madoz
Frequent Advisor

Re: rp3440 connected to msa30 cannot activate vg

We changed both because it was impossible to activate the vg
Gabriel Madoz
Torsten.
Acclaimed Contributor

Re: rp3440 connected to msa30 cannot activate vg

Do you have any data collection from a point in time before replacing the 2 disks (sautil/saconfig)?

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Gabriel Madoz
Frequent Advisor

Re: rp3440 connected to msa30 cannot activate vg

saconfig

******************** SmartArray RAID Controller /dev/ciss4 ********************

Auto-Fail Missing Disks at Boot = enabled
Cache Configuration Status = write cache temporarily disabled (code=1)
Cache Ratio = 50% Read / 50% Write

---------- PHYSICAL DRIVES ----------

Location Ch ID Size Status

Internal 1 0 146.8 GB OK
Internal 1 1 146.8 GB OK
External 2 0 146.8 GB OK
External 2 1 146.8 GB OK

---------- LOGICAL DRIVE 0 ----------

Device File = c4t0d0
RAID Level = 1+0
Size = 140009 MB
Stripe Size = 128 KB
Status = OK

Participating Physical Drive(s):

Ch ID

1 0
1 1

Participating Spare Drive(s):

None

---------- LOGICAL DRIVE 1 ----------

Device File = c4t0d1
RAID Level = 1+0
Size = 140009 MB
Stripe Size = 128 KB
Status = FAILED

Participating Physical Drive(s):

Ch ID

2 0
2 1

Participating Spare Drive(s):

None
-------------------------------------
sautil

******************************************************************************
**** ****
**** S A U T I L S u p p o r t U t i l i t y ****
**** ****
**** for the HP SmartArray RAID Controller Family ****
**** ****
**** version A.02.12 ****
**** ****
**** (C) Copyright 2003-2007 Hewlett-Packard Development Company, L.P. ****
******************************************************************************



---- DRIVER INFORMATION ------------------------------------------------------

Driver State........................ READY

---- CONTROLLER INFORMATION --------------------------------------------------

Controller Product Number........... A9891A
Controller Product Name............. HP PCI-X SmartArray 6404 (Ch A1, A2)
Hardware Path....................... 0/2/1/0/4/0
Device File......................... /dev/ciss4

---- DRIVER STATISTICS -------------------------------------------------------

Rover Statistics:
Rover busy.......................... 0
Rover cmd failed.................... 0
Rover invalid class................. 0
Rover invalid sub class............. 0
Rover invalid detail................ 0
IOCTL command failed................ 0
IOCTL call failed................... 0
Invalid IOCTL....................... 0
Internal driver cmd failed.......... 0
Resets.............................. 0
Probe failed........................ 0
Heartbeat lost...................... 0

Events Statistics:
Init................................ 1
FW ready............................ 1
Init ok............................. 1
Init failed......................... 0
Suspend............................. 0
Suspended........................... 0
Download............................ 0
IO quiesced......................... 0
HW quiet............................ 0
Reset ok............................ 0
Download ok......................... 0
IO quiesce timeout.................. 0
Download timeout.................... 0
HW quiet timeout.................... 0
Reset timeout....................... 0
FW lockup........................... 0
Invalid event....................... 0

OLAR Statistics:
Suspend requested................... 0
Suspend forced...................... 0
Resume request...................... 0
Resume failed....................... 0

Driver Command Statistics:
Completed after timeout............. 0
SM Command Failed................... 0
IOs in activeQ (suspd).............. 0
Driver not ready open failed........ 0
Current lun open count.............. 1
Request failed - drv state.......... 0
CMD allocation failure.............. 0
IOs queued on send Q................ 0
Zero sized IO....................... 33
DMA setup fail count................ 0
Out of sgle......................... 0
Inquiries to NE LUN 0............... 0
CAC with no sense data.............. 0
Non active powerfail IO............. 0
Underruns........................... 6
Overruns............................ 0
Command invalid..................... 0
Other IO errors..................... 0
Interrupt while state invalid....... 0
Spurious interrupts................. 5
Not SU failure...................... 0
External register read request...... 0
PCI config reads.................... 40
Invalid register type............... 0
Invalid register length............. 0
Invalid register offset............. 0
Invalid register alignment.......... 0
Delete lun while open............... 0
Data copy failed.................... 0
DMA map failed...................... 0
BAR map failed...................... 0

******************************************************************************
**** End of SAUTIL Output ****
******************************************************************************

Another log

CURRENT MONITOR DATA:

Event Time..........: Sun Nov 14 19:50:29 2010
Severity............: CRITICAL
Monitor.............: dm_raid_adapter
Event #.............: 2
System..............: mvdh05.lac.nsroot.net

Summary:
Adapter at hardware path 0/2/1/0/4/0 : CISS: RAID SA controller is now
online.



Description of Error:


lbolt value: 2900

CISS: RAID SA controller is now on-line.


Probable Cause / Recommended Action:

No Action required. Information message only.

Additional Event Data:
System IP Address...: 169.167.27.10
Event Id............: 0x4ce059a500000000
Monitor Version.....: B.01.00
Event Class.........: I/O
Client Configuration File...........:
/var/stm/config/tools/monitor/default_dm_raid_adapter.clcfg
Client Configuration File Version...: A.01.00
Qualification criteria met.
Number of events..: 1
Associated OS error log entry id(s):
0x4ce0580400000000
Additional System Data:
System Model Number.............: 9000/800/rp3440
OS Version......................: B.11.11
EMS Version.....................: A.04.20
STM Version.....................: A.57.00
Latest information on this event:
http://docs.hp.com/hpux/content/hardware/ems/dm_raid_adapter.htm#2

v-v-v-v-v-v-v-v-v-v-v-v-v D E T A I L S v-v-v-v-v-v-v-v-v-v-v-v-v



I/O Log Event Data:

Driver Status Code..................: 0x00000002
Length of Logged Hardware Status....: 0 bytes.
Offset to Logged Manager Information: 0 bytes.
Length of Logged Manager Information: 12 bytes.

Manager-Specific Information:

Raw data from the SCSI RAID SA Controller CISS driver:
00000004 00000B54 00000000




Gabriel Madoz
Torsten.
Acclaimed Contributor

Re: rp3440 connected to msa30 cannot activate vg

This is the same as in your first post, but I don't know if this is made with the new or old disks...

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Gabriel Madoz
Frequent Advisor

Re: rp3440 connected to msa30 cannot activate vg

With the old
Gabriel Madoz
Torsten.
Acclaimed Contributor

Re: rp3440 connected to msa30 cannot activate vg

Not enough information. You cannot say what the problem was.
Both disks are shown as good, but the RAID is failed.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Gabriel Madoz
Frequent Advisor

Re: rp3440 connected to msa30 cannot activate vg

Ok, this was always the situation and once we changed smart array without improval changes
Gabriel Madoz
Torsten.
Acclaimed Contributor

Re: rp3440 connected to msa30 cannot activate vg

But now the problem is solved?

I'm not sure what was in the past and what is the current status ...



Next time use "sainfo" to make a data collection in case of problems.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!