- Community Home
- >
- Networking
- >
- Wireless
- >
- M and MSM Series
- >
- Re: Configuring Cisco Switch Interface for control...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-28-2014 02:21 AM
тАО02-28-2014 02:21 AM
Configuring Cisco Switch Interface for controlled MSM 460/466 Access Point
Hi,
I'm trying to configure a Cisco Switch (WS-2960S-48TS-L, WS-C3750G-48TS) Interface for use with a controlled MSM 460/466 Access Point. The Access Point should get an IP address in VLAN 20 and then trunk to the interface to get VLAN 20 and VLAN 1500 packets into the network. I tried this configuration and it works:
interface GigabitEthernet1/0/44
switchport trunk native vlan 20
switchport trunk allowed vlan 20,1500
switchport mode trunk
Anyone using a similar setup and a different config?
Regards, Leonardo
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-16-2015 12:26 PM
тАО09-16-2015 12:26 PM
Re: Configuring Cisco Switch Interface for controlled MSM 460/466 Access Point
Hello, Thanks for your blog post, I have same setup but using HP MSM 720 and HP MSM 460 with Cisco 2960 switch and two SSID; Guest(VLAN 20) and Staff (VLAN 100). I have setup the controller and it has discovered the AP but i cannot get IP adrress from my laptop. I have not yet got the switch logins. So should i make the port connecting the AP to the switch a trunk for VLAN 20,100 and Native VLAN 1?
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-16-2015 10:47 PM
тАО09-16-2015 10:47 PM
Re: Configuring Cisco Switch Interface for controlled MSM 460/466 Access Point
Hi,
yes, the port should be configured as trunk. The native VLAN is where the AP gets its IP address after booting (in your case VLAN 1?). You'll also need a DHCP server in VLAN 100 and 20 for clients connecting to the SSID.
Regards, Leonardo
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-18-2015 12:51 AM
тАО09-18-2015 12:51 AM
Re: Configuring Cisco Switch Interface for controlled MSM 460/466 Access Point
Thanks,
A quiz, between HP MSM 425 & MSM 460 which is stronger in coverage.
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-18-2015 01:02 AM
тАО09-18-2015 01:02 AM
Re: Configuring Cisco Switch Interface for controlled MSM 460/466 Access Point
Ask your preferred HP presales technician! ;-)