- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Netservers
- >
- After firmware upgrade
Netservers
1752765
Members
5339
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-05-2004 07:13 AM
тАО08-05-2004 07:13 AM
Hi all,
I have just upgraded an LP1000r to firmware version 04.06.31 RA. But after the update the system never booted. It just halts after reading it's NETraid configuration, it just says:
system configuration updated.
The system never completes it POST and therefor is unable to start the OS on the disks.
Is there anything I can do?
Rem
I have just upgraded an LP1000r to firmware version 04.06.31 RA. But after the update the system never booted. It just halts after reading it's NETraid configuration, it just says:
system configuration updated.
The system never completes it POST and therefor is unable to start the OS on the disks.
Is there anything I can do?
Rem
Solved! Go to Solution.
- Tags:
- firmware update
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-05-2004 08:53 PM
тАО08-05-2004 08:53 PM
Solution
Rem,
If it's an embedded netraid, try to get in the setup and then switch its configuration to scsi. I suppose you have taken note of the current RAID configuration...
Another thing you can try is to clear the CMOS by the jumper or switch this server has.
HTH
Oscar
If it's an embedded netraid, try to get in the setup and then switch its configuration to scsi. I suppose you have taken note of the current RAID configuration...
Another thing you can try is to clear the CMOS by the jumper or switch this server has.
HTH
Oscar
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-05-2004 09:39 PM
тАО08-05-2004 09:39 PM
Re: After firmware upgrade
Oscar,
Thanks for your reply. There was nothing wrong with the controller. After using the clear CMOS switch the server booted normally.
Remco
Thanks for your reply. There was nothing wrong with the controller. After using the clear CMOS switch the server booted normally.
Remco
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP