- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Netservers
- >
- Re: Netserver LS will not boot
Netservers
1753548
Members
5740
Online
108795
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-18-2001 10:47 AM
тАО07-18-2001 10:47 AM
Netserver LS will not boot
I have an older Netserver LS/2 that will not boot. I get no errors, it just stops after checking the HP disk array. It won't boot from floppy or CD-ROM. Any suggestions?
Thanks.
Thanks.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-18-2001 01:44 PM
тАО07-18-2001 01:44 PM
Re: Netserver LS will not boot
Gary,
1. Check the boot order in the system setup (F2 at startup). The default is usually floppy, CD, then hard drive.
2. Check the NetRaid config (ctrl-M during startup).
Can you boot from a floppy or CD?
--Joe
1. Check the boot order in the system setup (F2 at startup). The default is usually floppy, CD, then hard drive.
2. Check the NetRaid config (ctrl-M during startup).
Can you boot from a floppy or CD?
--Joe
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-23-2001 09:25 AM
тАО07-23-2001 09:25 AM
Re: Netserver LS will not boot
I would try and clear the cmos, which will require you to boot onto the ECU utility and reconfigure your deviced. Here is a link to show you where the clear cmos switch is located:
http://netserver.hp.com/support/parts_service/system_board/sys_board_tpl.asp?pid=LS
http://netserver.hp.com/support/parts_service/system_board/sys_board_tpl.asp?pid=LS
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP