- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: telnet problem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2005 06:00 PM
тАО02-14-2005 06:00 PM
Re: telnet problem
#lanadmin
choose "Lan"
choose "Display"
post this output
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2005 06:04 PM
тАО02-14-2005 06:04 PM
Re: telnet problem
the o/p:
LAN INTERFACE STATUS DISPLAY
Tue , Feb 15,2005 14:56:12
PPA Number = 0
Description = lan0 Hewlett-Packard LAN Interface Hw Rev 0
Type (value) = ethernet-csmacd(6)
MTU Size = 1500
Speed = 10000000
Station Address = 0x800090b6bc1
Administration Status (value) = up(1)
Operation Status (value) = up(1)
Last Change = 100
Inbound Octets = 1706372337
Inbound Unicast Packets = 636673
Inbound Non-Unicast Packets = 16688042
Inbound Discards = 0
Inbound Errors = 5
Inbound Unknown Protocols = 391753
Outbound Octets = 502536755
Outbound Unicast Packets = 666978
Outbound Non-Unicast Packets = 1652
Outbound Discards = 0
Outbound Errors = 0
Outbound Queue Length = 0
Specific = 655367
Press
Ethernet-like Statistics Group
Index = 1
Alignment Errors = 0
FCS Errors = 0
Single Collision Frames = 62887
Multiple Collision Frames = 53357
Deferred Transmissions = 296007
Late Collisions = 0
Excessive Collisions = 0
Internal MAC Transmit Errors = 0
Carrier Sense Errors = 0
Frames Too Long = 0
Internal MAC Receive Errors = 0
LAN Interface test mode. LAN Interface PPA Number = 0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2005 06:16 PM
тАО02-14-2005 06:16 PM
Re: telnet problem
It's not showing whether network card set to half or full duplex (where as my systems are showing)
#lanadmin -X 100FD 0
check the telnet speed after issuing this command, if still slow enter the command
#lanadmin -X 100HD 0
let us know the result and also check for file systems (bdf) whether any one filled.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2005 09:16 PM
тАО02-14-2005 09:16 PM
Re: telnet problem
i think SAM is very god for administration of hp-ux.to enable and disable interface is very easy to do with sam.modify interface in half/full or modify autonegotiate.
i have problem, interface is up and at the catalyst is connect but i can't connect to this interface.This is configurations of lan2:
Card Type: Fast Ether
Autoneg: OFF
Speed (million bps): 100
Duplex Mode: FULL
at port catalyst, we set to autonego is on with 100 full duplex.
what,s wrong??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2005 03:28 PM
тАО02-15-2005 03:28 PM
Re: telnet problem
If lan2 is up and you have already set to correct configuration.
One this need to consider: IP address and network trouble!
And should check for hardware:
#ioscan -fnC lan
Regard,
HoangChiCong
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-15-2005 05:45 PM
тАО02-15-2005 05:45 PM
Re: telnet problem
Reviewing your lanadmin display, you are working with a 10mb card. A 10mb card is only half-duplex.
Additionally, you have a high number of collisions on this card. Check or replace your lan cable or connection.
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-16-2005 02:30 AM
тАО02-16-2005 02:30 AM
Re: telnet problem
In addition to checking/setting the duplex on your machine, you must also make sure that the switch port is set the same. Otherwise, chaos will ensue...
Regards,
Mark
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2005 07:01 PM
тАО02-22-2005 07:01 PM
Re: telnet problem
If it's Coax cable, I'd suggest checking the termination of the segment, and that none of the cables have been damaged.
HTH
- « Previous
-
- 1
- 2
- Next »