- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- HP 2920 Vlan multiple gateway
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-25-2016 04:31 AM
04-25-2016 04:31 AM
HP 2920 Vlan multiple gateway
Hi All ,
As there is no PBR feature on this switch is it possible to do the following :
Current default route : 0.0.0.0 0.0.0.0 10.0.99.254
But I would need to create individual gateways for each vlan as in :
Vlan 1 : 0.0.0.0 0.0.0.0 10.0.1.254
Vlan 10: : 0.0.0.0 0.0.0.0 10.0.10.254
Vlan 20: : 0.0.0.0 0.0.0.0 10.0.20.254
so that if a client is on Vlan 1 or 10 trying to reach out the internet hits its own Vlan gw address instead of the 10.0.99.254 .
Is it possible with this switch, I would highly appreciate your help with this.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-25-2016 07:44 AM
04-25-2016 07:44 AM
Re: HP 2920 Vlan multiple gateway
Hello Jony,
You s
hould consider Layer 3 routes and Device Default Gateways as separate things.
Where is your default exit? 10.0.99.254? Or is this the IP of your 2920? Can you post your config on here?
On the 2920, you can have multiple VLANs with IPs (ex. vlan 1 ip address 10.0.1.254 255.255.255.0, vlan 10 ip address 10.0.10.254 255.255.255.0, etc). These IPs can serve as the default gateway for the PCs/devices.
You have have multiple routes as well, but the switch will pick 1. If they are the same cost and the switch supports equal cost routes, it will balance between them, BUT I DONT RECOMMEND THIS.
Recommended configuration would be the single default route (0.0.0.0 0.0.0.0. 10.0.99.x) and the multiple vlans i mentioned ealier.
Sincerely,
RK