- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- How to assign switch in stacked mode into Commande...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-10-2015 12:09 AM
04-10-2015 12:09 AM
Hi,
Can anyone here please susggest me what is the best way to swap the stacking configuration below so that the 48 ports switch can be the master / commander of the stacking switch ?
AV_Switch_1(config)# show stacking
Stack ID : 0200c434-6b8f0e40
MAC Address : c4346b-8838e3
Stack Topology : Chain
Stack Status : Active
Uptime : 1d 1h 6m
Software Version : WB.15.11.0007
Mbr
ID Mac Address Model Pri Status
--- ------------- -------------------------------------- --- ---------------
1 c4346b-8f0e40 HP J9729A 2920-48G-POE+ Switch 128 Standby
3 c4346b-8838c0 HP J9726A 2920-24G Switch 128 Commander
AV_Switch_1(config)#
Thanks in advance.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-13-2015 03:41 PM - edited 04-13-2015 03:47 PM
04-13-2015 03:41 PM - edited 04-13-2015 03:47 PM
Solution# redundancy switchover
standby will become commander
pay attention that the commander will reboot the primary image. It's wise to change the priority of the member so that in case of a complete reboot the 48 port will become the commander
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-13-2015 03:50 PM
04-13-2015 03:50 PM
Re: How to assign switch in stacked mode into Commander / master ?
Sietze,
so I issue that command from anywhere I connect the serial console in the Config prompt ?
after that it will just flip the order / fialover the status.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-13-2015 11:30 PM
04-13-2015 11:30 PM
Re: How to assign switch in stacked mode into Commander / master ?
The slave will flipover to master, and the master will reboot. So your current master/commander will be rebooted.
I have tested it via console in enable mode. But I believe you can do it via telnet/ssh.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-13-2015 11:34 PM
04-13-2015 11:34 PM
Re: How to assign switch in stacked mode into Commander / master ?
Cool, thanks Sietze