- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Dl380 Gen9 Won't boot after reboot. - It was just ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-20-2015 04:21 PM
12-20-2015 04:21 PM
Dl380 Gen9 Won't boot after reboot. - It was just fine before!
Hello
I have a DL390 Gen9 that after a reboot, it wont boot into windows. I have an OCZ Revo Drive and 6 - 2.5" SAS drives in a RAID5 with a hot spare. The OS is on the Revo Drive with Windows 2012 R2 and the data is on the RAID. Originally the OS and data were both on the RAID, but once the server rebooted the OS would not come back up. I tried fixing the mbr, tried repairing windows, and nothing worked. I ended up reinstalling windows. It booted up and life was great, but once it rebooted agian, the same issue occured. Just incase, I installed the OS on the revo drive. I did not reboot afterwards, but they had a scheduled power outage in that office and now that the server rebooted it wont come up again.
I have tried both UEFI and Legacy BIOS mode, tried wiping the RAID, and recreating it, and there are no USB drives or what not plugged into it.
Also, the RAID is set as GPT with 1TB drives, but this is only data now, the OS is on the Revo Drive which is 250GB.
Do yall have any ideas of what could make it not boot into the OS?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-20-2015 09:19 PM
12-20-2015 09:19 PM
Re: Dl380 Gen9 Won't boot after reboot. - It was just fine before!
I'm not familiar with the Revo drive, but I'd guess the issue is with what the system sees as the boot device.
Also, if the OS is installed in UEFI, it will not boot in Legacy Boot mode and vice-versa
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-20-2015 09:42 PM
12-20-2015 09:42 PM
Re: Dl380 Gen9 Won't boot after reboot. - It was just fine before!
I used intelligent provisioning when I had installed the OS on the RAID and did it directly with the Windows installer disk the second time
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-21-2015 06:21 AM
12-21-2015 06:21 AM
Re: Dl380 Gen9 Won't boot after reboot. - It was just fine before!
So your saying without the extra Revo drive installed you're still having problems? Nothing special to install 2012 on a Gen9 that I'm aware of. For 2008 you have to disable UEFI Optimized Boot, this is not required for 2012.
You might look at the UEFI Deployment Guide