- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: ML330G3 - ATA RAID operations - OS upgrade sce...
ProLiant Servers (ML,DL,SL)
1753884
Members
7706
Online
108809
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-30-2008 06:53 AM
тАО10-30-2008 06:53 AM
Our ML330G3 is equiped with the following 3 drives:
I - ATA drive with OS and applications
II - ATA drive, mirrored from drive I through RAID-1
III - SCSI drive with data
We are looking to perform an OS upgrade and our strategy is the following:
1 - Disable RAID configuration
2 - Perform clean install on drive II
3 - Configure OS and apps, and if everything tests ok, enable RAID configuration with drive I now mirrored from drive II
Installation and configuration is being simulated in a lab. The problem is that we have no experience performing RAID operations. The documentation we found is limited and appears to imply that disabling RAID will cause immediate loss of data from both drives. We are confused. How do we go about carrying out our upgrade strategy? Where can we find more thorough documentation? Hopefully the answer to these questions will help us know what to do in a recovery scenario as well.
I - ATA drive with OS and applications
II - ATA drive, mirrored from drive I through RAID-1
III - SCSI drive with data
We are looking to perform an OS upgrade and our strategy is the following:
1 - Disable RAID configuration
2 - Perform clean install on drive II
3 - Configure OS and apps, and if everything tests ok, enable RAID configuration with drive I now mirrored from drive II
Installation and configuration is being simulated in a lab. The problem is that we have no experience performing RAID operations. The documentation we found is limited and appears to imply that disabling RAID will cause immediate loss of data from both drives. We are confused. How do we go about carrying out our upgrade strategy? Where can we find more thorough documentation? Hopefully the answer to these questions will help us know what to do in a recovery scenario as well.
Solved! Go to Solution.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-31-2008 06:02 AM
тАО10-31-2008 06:02 AM
Solution
First, I think what you read is misleading. If you were to go into the RAID setup and delete the RAID set, The data may get effected depending on what the controller does at the time of deleting the RAID set info. For a RAID 1, this may not be true, but for a RAID 5 it is definately true, so there in lies the confusion.
Breaking the RAID is another matter, i.e. removing on of the drives in the RAID 1 set. This will cease the RAID function, but leave the SSet info intact, with function returning when the set drives are back to the original numbers. I think this is what you wish to accomplish.
Now, my question would be about why you have the architecture you have, mirroring the OS and not the data. To me this is backwards, a simple ghost or backup of the OS drive would keep your new install and configuration clean from corruption and give you a restore point in the OS should fail, while mirroring the data keeps your data always available even if a drive should fail.
We never recommend a mirror of a Windows OS due to the high disk usage of Windows. The RAID controller is working overtime just to keep up with all the Windows reads and writes, not to mention all the temporary data. We actual would setup up a RAID 1 on 4 drives, 2 for the OS and 2 for the data, then break the OS RAID and keep the clean set member offline for a backup and quick swap in if a restoation is needed of the OS.
Just my thoughts.
Breaking the RAID is another matter, i.e. removing on of the drives in the RAID 1 set. This will cease the RAID function, but leave the SSet info intact, with function returning when the set drives are back to the original numbers. I think this is what you wish to accomplish.
Now, my question would be about why you have the architecture you have, mirroring the OS and not the data. To me this is backwards, a simple ghost or backup of the OS drive would keep your new install and configuration clean from corruption and give you a restore point in the OS should fail, while mirroring the data keeps your data always available even if a drive should fail.
We never recommend a mirror of a Windows OS due to the high disk usage of Windows. The RAID controller is working overtime just to keep up with all the Windows reads and writes, not to mention all the temporary data. We actual would setup up a RAID 1 on 4 drives, 2 for the OS and 2 for the data, then break the OS RAID and keep the clean set member offline for a backup and quick swap in if a restoation is needed of the OS.
Just my thoughts.
Hot Swap Hard Drives
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2008 06:35 AM
тАО11-03-2008 06:35 AM
Re: ML330G3 - ATA RAID operations - OS upgrade scenario
Thank you very much for the repply. You are absolutely right about we having it backwards. You are also right about what we are trying to do. We are newbies here working with a setup from another newby...
At any rate, here is our updated strategy, given that the drives have the required capacity:
- For safety, build image of RAIDed OS drive, in this case drive I.
- Quick format drive I and transfer data from the data disk (drive III) to drive I (Without any change in RAID configuration, which means data will be transfered to both RAID-1 drives)
- Install new OS on drive III (Leaving the OS on the non-RAID drive)
Which should leave us with the following drive configuration:
I - Drive in the unchanged RAID configuration, only now it contais data and not the OS
II - Mirrored RAID drive, now with a copy of the data
III - Non-RAID OS drive
Will this work?
Also, if we get another drive to RAID the OS as well: Just add the drive, run the RAID configuration utility to add it, and then remove it again if we want to keep it offline. Correct?
At any rate, here is our updated strategy, given that the drives have the required capacity:
- For safety, build image of RAIDed OS drive, in this case drive I.
- Quick format drive I and transfer data from the data disk (drive III) to drive I (Without any change in RAID configuration, which means data will be transfered to both RAID-1 drives)
- Install new OS on drive III (Leaving the OS on the non-RAID drive)
Which should leave us with the following drive configuration:
I - Drive in the unchanged RAID configuration, only now it contais data and not the OS
II - Mirrored RAID drive, now with a copy of the data
III - Non-RAID OS drive
Will this work?
Also, if we get another drive to RAID the OS as well: Just add the drive, run the RAID configuration utility to add it, and then remove it again if we want to keep it offline. Correct?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP