- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: battery status failed
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-19-2014 10:49 PM
тАО08-19-2014 10:49 PM
battery status failed
I had a problem with my Hp proliant DL 180G5 server, in this server i have smart array e200 controller. when i browse this controller through web i t is showing some error in acceleration as
status Temporarily Disabled
Error code Cache Disabled Low Battery
Battery Status Failed
So, with this message we have replaced the battery, but the error still the same. So my next step is to upgrade the firmware of the controller. Do you think this is the right decision, if so please tell me how to do this firmware updating, and also I need to know that if the firmware is updated any raid configuration is changed.
please help me what to be done.
- Tags:
- bbwc
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-20-2014 02:35 PM
тАО08-20-2014 02:35 PM
Re: battery status failed
There should have been a message when it booted up saying the battery was charging, and the array config util should show something about it charging.
If it still says it's a bad battery, then the new one might actually be bad if it's already tried to charge up for 24 hours and still didn't hold enough charge.
Some people who sell replacement batteries are selling new/old stock components that have been sitting on a shelf for 5+ years, so look at the date and make sure your new one is actually recently manufactured.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-30-2014 11:37 AM
тАО08-30-2014 11:37 AM
Re: battery status failed
However I suspect not only your Smart Array Controller has very outdated firmware, but your whole server has.
It might be easier to update your entire server with the Service Pack for ProLiant.
However HP recommends not skipping 1 SPP version in one go.
So you would have to go quite a while back in the archives to get your server up to date.
Also please keep in mind that HP only supports servers with firmware within 1 year of the latest SPP/release for that specific server. If the latest firmware is a critical update all other firmwares would even be considered no longer supported.
So if, god forbids, you have have a serious issue that is difficult to trace down town to one component (random shut downs without entries in logs/message on screen/red leds once every 3 months or something along those lines) you would have to go through a whole update process.
Also if you update in small steps (not skipping more than 1 SPP at the time) no settings should be lost, however if you decided to update to the latest version at once your BIOS settings might get restored to default (though no raid-configuration should get lost as this is stored on the hard drives them-self).
But as Waaronb says you would expect a different message now then failed battery.
So I would suggest:
-Update server
-If issue persist replace battery and cache module in one go.
-If even that fails there is most likely an issue with the controller (systemboard in your case).