- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- MSA 1040: How to discover WWN initiator
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-01-2016 03:38 PM
08-01-2016 03:38 PM
MSA 1040: How to discover WWN initiator
Good Morning,
I'm Braziliam and my english is very bad, any form I will try explain my quest.
This is may scenary:
I have a MSA 1040 Storage, 1 volume with 1TB created and need presend this volume to server.
The server have two HBA controllers.
First I create two iniciators, one for each ports of HBA:
After that, I map (Volumes > Action > Map Volume) the volume for WWN's above, see below:
Even mapped, I can not see the volume on the server.
My suspicion is that it is not showing up because even though I presented the WWN, the storage could not discover it, as shown inthe first picture.
How to solve this problem? I'm doing the right way?
Wait answers,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-08-2016 09:25 AM
08-08-2016 09:25 AM
Re: MSA 1040: How to discover WWN initiator
Hi, Is the server connected direct to MSA or through SAN Switch. According change the initiator topology to either point-to-point(PTP) or loop.
Secondly also verify the FC HBA drivers has been installed and its getting detected in device manager in server.
Regards,
Rajneesh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-09-2016 10:22 AM
08-09-2016 10:22 AM
Re: MSA 1040: How to discover WWN initiator
Hi,
I have a HP 8/20 SAN Switch connecting server to storage. I don't have access to settings of this switch, I will try this.
About driver, I have the last HBA driver version installed.
thanks for you answer...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-10-2016 04:52 AM
08-10-2016 04:52 AM
Re: MSA 1040: How to discover WWN initiator
Hello,
Hello,
Check if you have created the initiator correctly.
Creating an initiator.
To create an initiator
- Determine the FC or SAS WWN or iSCSI IQN to use for the initiator.
- In the Hosts topic, select Action > Create Initiator. The Create Initiator panel opens.
- In the Initiator ID field, enter the WWN or IQN. A WWN value can include a colon between each pair of digits but the colons will be discarded.
- In the Initiator Name field, enter a nickname that helps you easily identify the initiator. For example, you could use MailServer_FCp1. An initiator name is case sensitive and can have a maximum of 32 bytes. It cannot already exist in the system or include the following: " , . < \ If the name is used by another initiator, you are prompted to enter a different name.
- In the Profile list, select the appropriate option: ¢ Standard. Default profile. ¢ HP-UX. The host uses Flat Space Addressing.
- Click OK. The initiator is created and the hosts table is updated
Adding initiators to a host
To add an initiator to a host, the initiator must have the same mappings as all other initiators in the host. This means that the initiator must be mapped with the same access, port, and LUN settings to the same volumes or volume groups. To add initiators to a host
- In the Hosts topic, select 1–128 named initiators to add to a host.
- Select Action > Add to Host. The Add to Host panel opens.
- Perform one of the following: ¢ To use an existing host, select its name in the Host Select list. ¢ To create a host, enter a name for the host in the Host Select field. An host name is case sensitive and can have a maximum of 32 bytes. It cannot already exist in the system or include the following: " , . < \
- Click OK. For the selected initiators, the Host value changes from -nohost- to the specified host name.
Regards,
Jawad Ahmed
If you feel this was helpful please click the KUDOS! thumb below!