- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- Re: MSA2000 G3 FC - P2000 FC
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-17-2016 03:15 AM - edited 03-17-2016 04:14 AM
03-17-2016 03:15 AM - edited 03-17-2016 04:14 AM
Hello, I have a MSAP2000 G3 FC connected to 2 ESXi via FC, everyone ESXI is connected to each controller on the MSA2000, for redundancy.
Now, I've bought 2 StorageWorks 8/24 FC switch, that I want to use with the MSA2000 and three ESXI, 2 of them are the ones that are already connected directly to the MSA via FC.
My doubt is regarding the LUN's that I already have configured on those 2 ESXI, that are from MSA2000.
If I connect the MSA2000 to both StorageWorks and the ESXi also to both StorageWorks, would I lose the LUN's, or will them be visible as before?
Thanks a lot,
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-17-2016 05:01 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-17-2016 05:09 AM - edited 03-17-2016 05:09 AM
03-17-2016 05:09 AM - edited 03-17-2016 05:09 AM
Re: MSA2000 G3 FC - P2000 FC
... since you are about the handle the switch firmware right now (your other thread), don't forget to check the P2000 too, current version is TS252P001.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-17-2016 05:22 AM
03-17-2016 05:22 AM
Re: MSA2000 G3 FC - P2000 FC
Hi Torsten,
Yes, I have to check it also.
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-18-2016 06:29 AM - edited 03-18-2016 07:05 AM
03-18-2016 06:29 AM - edited 03-18-2016 07:05 AM
Re: MSA2000 G3 FC - P2000 FC
Hi Torsten,
Do I have to be in a specific version to upgrade to the last one?
I've read it says:
NOTE: Please upgrade all your arrays to TS250 or latest released firmware version before going with TS252 flashing.
How do I know wich version I am on? On Enclosure View, I see a line with this information:
EMP A Revision 2023
EMP B Revision 2023
I can't figure out how to link it to TSxxx.
Regards,