- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: VLAN Help Tagging/Untagging
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-06-2006 09:41 PM
тАО08-06-2006 09:41 PM
Re: VLAN Help Tagging/Untagging
Thanks very much for your help so far.
We have managed to configure all of VLANs, however we have hit a problem whilst trying to create the ACL for VLAN200. We get this error...
HP ProCurve Switch 5308xl# config
HP ProCurve Switch 5308xl(config)# access-list 200 permit ip host 172.16.0.1 any
Invalid input: permit
HP ProCurve Switch 5308xl(config)#
Any ideas why it is coming up with this error?
Once again, thank you VERY much for your time... its going very well at the moment.
Points assigned :-)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-06-2006 10:26 PM
тАО08-06-2006 10:26 PM
Re: VLAN Help Tagging/Untagging
I want to apologize for the ACL 200 and 400 , please change the numbers and make it less than 200 like , the ACL 200 make it ACL 102 , and ACL 400 make it ACL 104.
Explaination:
<100-199> ACL numbers to Configure an extended Access Control List.
Good Luck !!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-07-2006 02:27 AM
тАО08-07-2006 02:27 AM
Re: VLAN Help Tagging/Untagging
We cant seem to get our servers or workstations on VLAN200 to communicate with any other VLAN, or gain access to the internet.
Please see attached our ACLs.
The main server on VLAN200 is running DHCP and can communicate fine with our workstations. But this fails when trying to communicate with other VLANS.
The workstations on VLAN200 need to access the following IP's...
172.16.0.1
172.16.0.2
172.16.0.5
172.16.0.12
172.16.0.254 (internet gateway)
Could you please advise.
Many thanks once again... great support from yourself. :)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-07-2006 04:00 AM
тАО08-07-2006 04:00 AM
Re: VLAN Help Tagging/Untagging
I think its now your mistake :)
you missed the last tne the most important line in ACL200 (or now its 102) , which is :
(config)# access-list 102 permit ip any any ,
so now since you can't edit ACL102, just drop it, and past the configuration again in CLI after adding the previous line to the end.
Please let me know you have other problems :)
Good Luck !!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-07-2006 04:17 PM
тАО08-07-2006 04:17 PM
Re: VLAN Help Tagging/Untagging
I took another look on the config. of ACL102 and the others also, and i think it has some wrong lines.
Asper what i know from your old posts, i reconfigured the ACLs for you, see the attached file.
Good Luck !!!
- « Previous
- Next »