- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: SAM is not working
Operating System - HP-UX
1754273
Members
2989
Online
108813
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-19-2010 11:58 AM
03-19-2010 11:58 AM
Solution
Thye fastest way to run sam or smh is to make sure the variable DISPLAY is not set. Do this:
unset DISPLAY
Then run sam or smh. It will come up in character mode. If DISPLAY is set, you must have already installed an Xwindow server such as eXceed or Reflection/X or some other X11 windows tool and configure it to work on your PC. Then there are issues with X11 forwarding, Xauthority and even network routers that can block Xwindows protocol.
You can do everything in the character mode interface (CUI) that you can in the fancy GUI but you may be struggling with X11 for a while. Note that at 11.31, the Xwindow desktop (and therefore the XDMCP code) is not installed by default. I would leave it that way. There is no reason to run code on your HP-UX server that replaces your PC's desktop with an archaic interface. If you get your Xwindow emulator working, always verify with the simplest commands:
export DISPLAY=:0
(don't forget the .0)
/usr/bin/X11/xclock
(a small clock will be displayed) Close this window and you can run smh in GUI mode.
Bill Hassell, sysadmin
unset DISPLAY
Then run sam or smh. It will come up in character mode. If DISPLAY is set, you must have already installed an Xwindow server such as eXceed or Reflection/X or some other X11 windows tool and configure it to work on your PC. Then there are issues with X11 forwarding, Xauthority and even network routers that can block Xwindows protocol.
You can do everything in the character mode interface (CUI) that you can in the fancy GUI but you may be struggling with X11 for a while. Note that at 11.31, the Xwindow desktop (and therefore the XDMCP code) is not installed by default. I would leave it that way. There is no reason to run code on your HP-UX server that replaces your PC's desktop with an archaic interface. If you get your Xwindow emulator working, always verify with the simplest commands:
export DISPLAY=
(don't forget the .0)
/usr/bin/X11/xclock
(a small clock will be displayed) Close this window and you can run smh in GUI mode.
Bill Hassell, sysadmin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-28-2010 08:30 PM
04-28-2010 08:30 PM
Re: SAM is not working
Hi there
Maybe you can try this one
Verify of HPSMH ;autostart url` mode is ON by executing the command
# smhstartconfig
In case the autostart url mod is OFF, stop hpsmh by:
# /sbin/init.d/hpsmh stop
turn the autostart url mode by:
# smhstartconfig -a on -b off
Restart hpsmh
# /sbin/init.d/hpsmh start
Hope it works!
Thanks and Regards
Maybe you can try this one
Verify of HPSMH ;autostart url` mode is ON by executing the command
# smhstartconfig
In case the autostart url mod is OFF, stop hpsmh by:
# /sbin/init.d/hpsmh stop
turn the autostart url mode by:
# smhstartconfig -a on -b off
Restart hpsmh
# /sbin/init.d/hpsmh start
Hope it works!
Thanks and Regards
- « Previous
-
- 1
- 2
- Next »
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP