- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: X-server can not be started
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-24-2012 02:57 AM
01-24-2012 02:57 AM
Re: X-server can not be started
I need the "good" C-8000 to run for the next hour.
Meanwhile I will check the inside of the bad one and will try to swap the cards later.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-24-2012 04:48 AM
01-24-2012 04:48 AM
Re: X-server can not be started
Hi,
I rebooted the system but still, the same problem was there (including the LED lights).
> Red lights always on after reboot?
> Check if the card sits properly!
>Check for additional power (?)
> You could also test another slot ...
Now I open the machine and open the release card, then release the APG connectors screws from the rear panel (in order to swap between 2 graphic cards).
But I can't pull out the card from the slot and I don't want to use much power.
Is there any "trick" there ? Is there any user guide for that?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-24-2012 05:15 AM
01-24-2012 05:15 AM
Re: X-server can not be started
OK, I found how to do it... :)
Well now, after I swaped between the cards no Orange lights on the both rear and fron panel.
But still, graphinfo gives " unable to open device file at /dev/crt
Also, the same basic problem of this thread is there: X-server can not started.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-24-2012 05:59 AM
01-24-2012 05:59 AM
Re: X-server can not be started
See also:
http://h30499.www3.hp.com/t5/System-Administration/Xserver-problem/m-p/3160644#M159349
or Alex's hints here:
http://h30499.www3.hp.com/t5/System-Administration/X-crash/m-p/4891301#M402377
V.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-24-2012 06:02 AM
01-24-2012 06:02 AM
Re: X-server can not be started
ll /dev/gvid*
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-24-2012 06:08 AM
01-24-2012 06:08 AM
Re: X-server can not be started
No, I didn't , yet.
Please view the attached file.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-24-2012 06:44 AM
01-24-2012 06:44 AM
Re: X-server can not be started
I followed the instructions of this thread:
I attached the process results
I rebooted the system.
Still the same /dev/crt and dmesg problems.
I will try other solutions you offered.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-24-2012 08:32 AM
01-24-2012 08:32 AM
Re: X-server can not be started
Do you have the os installation cds?
Also the latest SW- and HWE bundles?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-25-2012 11:23 PM
01-25-2012 11:23 PM
Re: X-server can not be started
Hi,
I only have the OS and I have never installed some thing on my HP-UX.
Can you instruct me how to do it?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-30-2012 11:48 PM
01-30-2012 11:48 PM
Re: X-server can not be started
Hello experts,
Can someone help me with this issue?
BR,
Yali