- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: how to recover a vPar from Ignite backup
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-12-2007 04:12 PM
тАО11-12-2007 04:12 PM
I need your help to resolve recovery issue in below scenario:
--vPar(PA-RISC and Itanium) used make_net_recovery command to create backup.
--the vPar can not boot up due to disk failure after the backup taken successfully
What is the procedure to recover from the Ignite backup stored in the server?
Thanks
Wallace
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-12-2007 08:07 PM
тАО11-12-2007 08:07 PM
Solution- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-12-2007 08:20 PM
тАО11-12-2007 08:20 PM
Re: how to recover a vPar from Ignite backup
You just need to boot the failed vpar and point the boot kernel to your Ignite-UX Server,
for PA-RISC:
# vparboot -p
I don't know what version of vpar you used, but check this documentation, chapter 10, "network and tape recovery":
http://docs.hp.com/en/T1335-90073/T1335-90073.pdf
Regards,
Sandy
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-12-2007 09:33 PM
тАО11-12-2007 09:33 PM
Re: how to recover a vPar from Ignite backup
Take care because in the latests versions of ignite you can't define a route to the server, then a good idea is to use a cross ethernet between the lan of your ignite server and one IO of the vpar, then use vparload -p partitionname -I
ruben.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-13-2007 11:04 AM
тАО11-13-2007 11:04 AM
Re: how to recover a vPar from Ignite backup
All your replies are top of the rank.
Thanks you so much.
Wallace