- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: rx2800 doesn't prompt for ORCA during POST
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-07-2011 01:50 PM
тАО11-07-2011 01:50 PM
This is a strange one. I've got a new system rx2800 that I want to configure with RAID 10.
During the startup it never prompts to go into ORCA.
I'm using the iLO serial console.
It does state "Currently the controller is in RAID mode" but no prompt.
The last system I configured (about a year ago) was super easy..If I recall it even stated something like F8 to configure.
I've got to be doing something wrong..
Any ideas??--Thanks in advance--Bob
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-07-2011 09:23 PM - edited тАО11-07-2011 09:24 PM
тАО11-07-2011 09:23 PM - edited тАО11-07-2011 09:24 PM
SolutionYou need to install the saupdate.efi utility before you can use ORCA - see the attachments for details on how to obtain saupdate.efi, change the mode of the RAID controller and configure RAID volumes.
Note: Even though the attachments refer to the BL8x0c i2 servers the procedures are the same for the rx2800 i2 servers.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-07-2011 09:50 PM
тАО11-07-2011 09:50 PM
Re: rx2800 doesn't prompt for ORCA during POST
AFAIR you can start ORCA only by running this
drvcfg -s <Driver ID> <Ctril ID>
from EFI shell.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Tags:
- drvcfg
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-07-2011 10:31 PM
тАО11-07-2011 10:31 PM
Re: rx2800 doesn't prompt for ORCA during POST
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-08-2011 06:36 AM
тАО11-08-2011 06:36 AM
Re: rx2800 doesn't prompt for ORCA during POST
Thanks!..I'm sure this is it