- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: view current temperature
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-25-2007 07:28 PM
тАО06-25-2007 07:28 PM
can anybody tell me how to view the current temperature level on an hp rp 7420 box from command line ? (hpux 11.23)
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-25-2007 07:37 PM
тАО06-25-2007 07:37 PM
SolutionLog on to the MP, change to the command menu (cm) and run "de" - select "u":
MP:CM> de
Display status of the selected MP entity (for use by trained personnel only)
B - BPS (Bulk Power Supplies)
U - CLU (Cabinet Utilities: Fans, Intrusion, Clock's etc.)
A - PACI (Partition Console Interface)
G - MP (Management Processor)
P - PM (Power Management)
H - Cell Board Controller (PDHC)
Select device: u
...
Inlet Air Temperature : 20 deg C
run again and select "h":
H - Cell Board Controller (PDHC)
Select device: h
Enter cell number: 0
...
CPU 0 Temp : 0 deg C
CPU 1 Temp : 0 deg C
CPU 2 Temp : 0 deg C
CPU 3 Temp : 0 deg C
MMU Temp : 33 deg C
Cell Board Temp : 31 deg C
(depending on the CPU type the system cannot get the CPU temp - 0 deg is normal)
That's it.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-25-2007 07:43 PM
тАО06-25-2007 07:43 PM
Re: view current temperature
thanks a lot
it is workin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-25-2007 07:47 PM
тАО06-25-2007 07:47 PM
Re: view current temperature
Please read this too:
http://forums1.itrc.hp.com/service/forums/helptips.do?#33
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-25-2007 08:41 PM
тАО06-25-2007 08:41 PM