- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: LTO 7 - Data Rate Matching
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2016 11:07 PM
тАО06-08-2016 11:07 PM
LTO 7 - Data Rate Matching
I recently just purchased a MSL2024 with a LTO7 SAS drive. I can't find any documentation anywhere that states what the Data Rate Matching - ATS data transfer rate range (native) is. For LTO 6 it was 54 to 160MB/s. I saw on the IBM wesbite for their drives its 100 - 300MB/s.
Our system is hooked up to an Editshare XStream ST server, which has the ability to pass around 500MB/s, but when doing backups I tend to be able to only get around 180MB/s, and for reads I get from 180-210MB/s.
I'm assuming these speeds will be the zone to allow Data Rate Matching to occur and therefore not shoe shine the drives. But annoyingly can't find any info out there from HP.
I'm also investigating why I can't reach higher speeds from the system. But that may be on the editshare side of things.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-29-2016 06:13 AM
тАО06-29-2016 06:13 AM
Re: LTO 7 - Data Rate Matching
Hoping you have purchased LTO 7 Ultrium 15000 SAS Tape Drive
The Maximum ATS data transfer rate range ( native ) is 101 to 300 MB/s
The below guide Page 4 has the table you are looking for
http://www8.hp.com/h20195/v2/GetPDF.aspx/c04154359.pdf
Please note : the data write/read speed also depends on many factors including Host capability, HBA port speed, cable quality used, backups software settings, type of data been backed up and many more.
Anoop C
Note : I work for HPE
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-29-2016 04:15 PM
тАО06-29-2016 04:15 PM
Re: LTO 7 - Data Rate Matching
Well long story short, I did purchase the wrong drive and went through a saga to return it and get the right drive :)
But yup now all operating with the correct drive. Thanks for the info, I have received more info back from our hardware raid supplier and they informed me with the file types were moving, 180-200MB/s is what we should expect to see.
At least I know its not shoe shining based off the HP specs!
Regards
Craig