- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Web and Unmanaged
- >
- Re: HP ProCurve 1810G
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-30-2015 03:08 PM
03-30-2015 03:08 PM
HP ProCurve 1810G
Hi Guys,
in our production we have HP ProCurve 1810G - 24 GE, P.2.12, eCos-2.0, CFE-2.1
however when i try to configure the ports to fullduplex 1000Mbps its doesn't shows the 1000Mbps only 100FDX as last speed.
when i shows 100FDX the ports is configured on 100Mbps, when i chose Auto its picks up automatically 1000Mbps.
the switch is a Gigabyte switch, so why the ports doesn't shows 1000Mbps ?
thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-30-2015 07:38 PM
03-30-2015 07:38 PM
Re: HP ProCurve 1810G
You should not be disabling Auto on your Gb interfaces.
The IETF standard says,
"All 1000BASE-T PHYs shall provide support for Auto-Negotiation
(Clause 28) and shall be capable of operating as MASTER or SLAVE.
Auto-Negotiation is performed as part of the initial set-up of the link, and
allows the PHYs at each end to advertise their capabilities (speed, PHY
type, half or full duplex) and to automatically select the operating mode
for communication on the link. Auto-negotiation signaling is used for the
following two primary purposes for 1000BASE-T:
a) To negotiate that the PHY is capable of supporting 1000BASE-T half
duplex or full duplex transmission.
b) To determine the MASTER-SLAVE relationship between the PHYs at
each end of the link. 1000BASE-T MASTER PHY is clocked from a local source.
The SLAVE PHY uses loop timing where the clock is recovered from the received data stream."
99.9% of duplex mismatches are caused by people disabling Auto.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-01-2015 05:37 AM
04-01-2015 05:37 AM
Re: HP ProCurve 1810G
i have a 1820G "not the pro version
when i go to the port i can chose the 1000MB setting
on the pro version is not showing the 1000MB
are you saying the 1000MB is detected on the auto settings ?