Hewlett Packard Enterprise Community
Showing results for 
Search instead for 
Do you mean 
Looks like port-flapping - check the endpoints. And then check things like spanning tree. Maybe try...
by on ‎05-22-2016 11:39 PM
0 Replies 42 Views
0 Replies
42 Views
It is covered under warranty accordng to the terms. You may need to provide proof of purchase. The...
by on ‎05-22-2016 11:37 PM
0 Replies 36 Views
0 Replies
36 Views
Sample 3800 config attached   ; J9573A Configuration Editor; Created on release #KA.16.01.0006 ;...
by on ‎05-22-2016 11:28 PM
0 Replies 33 Views
0 Replies
33 Views
Some example lines from a switch I have worked on. [A 5406, but if the commands are supported, the ...
by on ‎05-22-2016 11:23 PM
0 Replies 30 Views
0 Replies
30 Views
The basic anwser is yes. Make sure you understand that this is management stacking, not port stacki...
by on ‎05-22-2016 11:19 PM
0 Replies 32 Views
0 Replies
32 Views
No. ProCurve switch of that vintage requires a ProCurve optic/DAC.
by on ‎05-22-2016 11:14 PM
0 Replies 25 Views
0 Replies
25 Views
You might also want to think about the HPE Network Optimizer solution specifically build around SDN...
by on ‎05-22-2016 11:13 PM
1 Reply 98 Views
1 Reply
98 Views
It is always worth adding syslog to the monitoring tools, eg: logging 10.20.30.185 this sends all...
by on ‎05-22-2016 10:51 PM
0 Replies 33 Views
0 Replies
33 Views
Sounds like you need to aggregate two links together using LACP. In the ProCurve world this is call...
by on ‎05-22-2016 10:47 PM
0 Replies 40 Views
0 Replies
40 Views
You have an advance replacement warranty - the defective item does not need to be collected at the ...
by on ‎03-01-2016 08:39 PM
0 Replies 122 Views
0 Replies
122 Views
You will need to log a call if there is an actual fault. You may be able to see somethng useful wi...
by on ‎02-26-2016 04:51 AM
0 Replies 1169 Views
0 Replies
1169 Views
Trying to do VSF over 20km with just 2 or 4 cores probably isn't an ideal use case anyway. Reason: ...
by on ‎02-26-2016 04:43 AM
1 Reply 1824 Views
1 Reply
1824 Views
This command has to be used very carefully, but it can be very useful at connection points/borders ...
by on ‎02-24-2016 01:05 AM
2 Replies 368 Views
2 Replies
368 Views
 You might want something like this (top line is the default route) ip route 0.0.0.0 0.0.0.0 172.2...
by on ‎02-24-2016 12:56 AM
2 Replies 151 Views
2 Replies
151 Views
Only one management module is supported in each switch - if there is a second, it is disabled (like...
by on ‎02-23-2016 06:44 AM
3 Replies 1861 Views
3 Replies
1861 Views
Max two switches, must be the same type (ie 5406+5406 or 5412+5412) 10Gb or 40Gb connections used...
by on ‎02-22-2016 07:44 PM
5 Replies 1907 Views
5 Replies
1907 Views
No. It may make sense for one of the controllers to just do guest (not manage any APs). You egress...
by on ‎02-20-2016 03:11 PM
0 Replies 79 Views
0 Replies
79 Views
0 Replies
81 Views
You may need to configure some users. This is the SNMPv3 setting for Network Protector SDN: snmpv3...
by on ‎02-20-2016 06:44 AM
1 Reply 103 Views
1 Reply
103 Views
The rails for the 2920 are the same as the 2530, 3800 and 5400R. I didn't know there were rails for...
by on ‎02-20-2016 06:41 AM
0 Replies 89 Views
0 Replies
89 Views