HP-UX for personal use?
Posted to: Operating System - HP-UX
a minute ago Is it possible to get an HP-UX license for personal use? Commercial UNIXes are a bit of a mystery to me and I'd like to try it out. 0 Kudos
1 View
0 Replies
Posted to: Operating System - HP-UX
savery a minute ago Is it possible to get an HP-UX license for personal use? Commercial UNIXes are a bit of a mystery to me and I'd like to try it out.Posted to: BladeSystem - General
dimka890 57m ago Hi all. I need help.FlexFabric 20/40 F8 module is connected to Cisco 9396PX with 40GbE QSFP-CR4 DAC cabels VC Q1.1 port status is "Not Linked". From Cisco side also No LinkI have two such modules, two cables, both are connected to Cisco and both have...Posted to: BladeSystem - General
dimka890 2 hours ago Hi all. I need help.FlexFabric 20/40 F8 module is connected to Cisco 9396PX with 40GbE QSFP-CR4 DAC cabels VC Q1.1 port status is "Not Linked". From Cisco side also No LinkI have two such modules, two cables, both are connected to Cisco and both have...Posted to: Servers - General
jrdjr yesterday Initial setup of an HPE rack with a HPE 1x1x8 G4 KVM IP Console Switch. Customer tried logging in as Admin with Admin as password and now it says we need a one time emergency paswword. Tried power cycling the KVM and still have same issue, all that c...Posted to: Servers - General
Dustin_Turner yesterday We are looking for oid files for the new ProLiant DL20 Gen10 Plus to use with our monitoring software. Searched online and unable to locate oid files for new DL20 Gen10.We have DL360 and DL380 up to gen 10 and are just nissing the DL20 Gen10 oid file...Posted to: Servers - General
KaungPing 14 hours ago Dear all,We have configured RAID 5 using HPE 6.4TB SAS 24G Mixed Use SSD(P49057-B21/)We have 8 SSD disk and created RAID 5 with the controller MR416i, the speed in RND4K Q1T1 Read is really slow.Can someone please advise what am i doing wrong? HPE M...Posted to: ProLiant Servers (ML,DL,SL)
PenProd yesterday I rent rack space for my Proliant server. I only have one ethernet cable going to the server but I need two - the second for iLO. To accomodate that, I've built in a small switch that's powered by 5V and only consumes about 200mW of power. It can be ...Posted to: ProLiant Servers (ML,DL,SL)
epyon79 yesterday long story short my server booted and ilo had "unknown" beside ipv4 address. i reset it, resetarted it and re set it up and same thing. no activity lights either. i have it on the shared port setting and the other nics work fine. nothings changed so ...Posted to: ProLiant Servers (ML,DL,SL)
Chris_Coates yesterday This is a DL380 gen 10. I need to expand the logical drive /array. The server was originaly built with 2 Arrays. Array 1 - 3 600GB SAS drives (RAID 1 with spare) for the OS (Disks are in bays 6-8) Array 2 - 13 2TB SATA drives for Data in a RAID 5 wit...Posted to: ProLiant Servers (ML,DL,SL)
ITLearner1 yesterday HiI have a DL380 Gen10 ServerEarlier i bought a u.2 backplane (826689-B21) + U.2 NVME enablement kit (873732-B21) and installed 8x3.84 TB U.2 Drivesand restarting the server: they are working well but i can't configure them to work as RAID (The drive...