- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Problem with installing HP-UX 10.20 ACE
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-09-2003 04:49 PM
тАО04-09-2003 04:49 PM
Problem with installing HP-UX 10.20 ACE
Could not perform the requested operation for "loopback:/", possibly due to network communications failure or the agent timing out. Check that the host is still accesible from the network, and the agent_timeout_minutes is not set too low.
During the installation i did not set for networking as my server is currently standalone.
Any one knows what is the problem?? and how to resolve???
thankss
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-09-2003 05:09 PM
тАО04-09-2003 05:09 PM
Re: Problem with installing HP-UX 10.20 ACE
Gather up this information and run:
set_parms initial
Also get your gateway ip.
The reboot will clean up anything hung in swagentd and you should be able to proceed.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-10-2003 12:15 AM
тАО04-10-2003 12:15 AM
Re: Problem with installing HP-UX 10.20 ACE
during the hp-ux installation, I did not enable networking.
I am doing a new installation. My hp is not connected, it is a standalone unit.
everytime during installation it gets to the above error msg, with 4 choices.
1: load sd from another depot.
2. retry(non interactive)
3. retry(interactive)
4. run from shell.
what should i do??
thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-10-2003 01:27 AM
тАО04-10-2003 01:27 AM
Re: Problem with installing HP-UX 10.20 ACE
swagentd is running.
You can re-bounce your daemon with
/usr/sbin/swagentd -r
Revert
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-10-2003 03:47 AM
тАО04-10-2003 03:47 AM
Re: Problem with installing HP-UX 10.20 ACE
One of the work arounds is to assign the hostname with the loopback address, but you haven't arrived here yet because you haven't configured you network parameters yet.
So I repeat:
set_parms initial
Then ps -ef | grep -i swagent
...to check for the swagent daemon.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-10-2003 05:00 AM
тАО04-10-2003 05:00 AM
Re: Problem with installing HP-UX 10.20 ACE
HP-UX is network sensitive, without the network you can't do any installation, since SD-UX check for hostname, IP during installation