- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: 5406zl config
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2008 11:13 AM
тАО04-28-2008 11:13 AM
i recently got a 5406.
i configured 3 vlans in addition to the administrative vlan.
vlan 2 = internet
vlan 3 = priv network
vlan 4 = priv network
so all the traffic routes properly within each vlan. now i have my firewall connected to vlan 2 which goes out to the internet. all the nodes from vlan 2 can get out to the internet, but vlan 3/4 cannot. i can ping the gateway of vlan 2 and the other nodes in vlan 2, but i cannot ping the firewall.
when i am plugged into vlan 2, it goes out fine, well here is the config. so the question is, how do i go about getting vlan 3/4 to route out to the internet too?
; J8697A Configuration Editor; Created on release #K.12.16
hostname "ProCurve Switch 5406zl"
module 1 type J8702A
module 2 type J8702A
ip default-gateway 192.168.100.1
ip routing
snmp-server community "public" Unrestricted
vlan 1
name "DEFAULT_VLAN"
no untagged A1-A24,B1-B24
no ip address
exit
vlan 2
name "internet"
untagged A1-A12
ip address 192.168.100.2 255.255.255.0
exit
vlan 3
name "spm_cluster"
untagged B1-B24
ip address 192.168.50.1 255.255.255.0
exit
vlan 4
name "spm_priv"
untagged A13-A24
ip address 192.168.10.1 255.255.255.0
exit
ip route 0.0.0.0 0.0.0.0 192.168.100.1
the switch can always ping the firewall, but the clients cannot. i've checked and double check the client and their gateways. i've been searching the forums for an answer for 3 days, but i have yet to figure it out. any help would be appreciated.
thanks.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2008 11:38 AM
тАО04-28-2008 11:38 AM
Solutionplease you write your firewall below command
ip route 192.168.100.0 255.255.255.0 192.168.100.2
ip route 192.168.50.0 255.255.255.0
192.168.50 1
ip route 192.168.10.0 255.255.255.0
192.168.10.1
and you assign each vlan member default gateway own vlan ip address
good luck...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2008 11:45 AM
тАО04-28-2008 11:45 AM
Re: 5406zl config
my firewall is 192.168.100.1 (it can be changed however)
vlan 2 administrative/gateway ip is 192.168.100.2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2008 09:58 PM
тАО04-28-2008 09:58 PM
Re: 5406zl config
you make write above ip routing command on firewall
good luck
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2008 06:12 AM
тАО04-30-2008 06:12 AM
Re: 5406zl config
problem solved!
the solution is to put the routes to your firewall so that it knows how to respond back to the switch.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2008 06:13 AM
тАО04-30-2008 06:13 AM