CLI-2> show version -all MSA1000 Firmware Revision: 7.00b1500 (0000JN710000) Build Time: 2007-01-24 16:13:17 MSA1000 Hardware Revision: 7 [AutoRev: 0x010000] Fibre Module AutoRev: 0x000000 Box 1a PROLIANT 4L7I DB Rev: 1.86 (0000JN710000) Box 1b PROLIANT 4L7I DT Rev: 1.86 (0000JN710000) Box 2 PROLIANT 4LEE Rev: CP20 (M0CNLMPX5F) Disk Drives: B T L BOX BAY GB Model Rev. Serial No. 0 0 0 1 1 300.0 COMPAQ BD30088279 HPB2 3KR0XDLR00007608J4JY 0 1 0 1 2 300.0 COMPAQ BD30088279 HPB2 3KR0Y3NS00007608W5LZ 0 2 0 1 3 300.0 COMPAQ BD30088279 HPB2 3KR0Y4NJ00007608QVSD 0 3 0 1 4 300.0 COMPAQ BD30088279 HPB2 3KR0Y39V00007608CHTV 0 4 0 1 5 300.0 COMPAQ BD300884C2 HPB7 VAVDBHVA0050B511081E 0 5 0 1 6 300.0 COMPAQ BD30088279 HPB2 3KR0YHKQ00007607ZUBK 1 1 0 1 9 146.8 COMPAQ BD14685A26 HPB8 3HY0LDQT00007335RJ2Q 1 2 0 1 10 146.8 COMPAQ BD14688278 HPB4 3KS0NMA600007641S2DW 1 3 0 1 11 146.8 COMPAQ BD14688278 HPB2 3KS1P30G000075524500 1 4 0 1 12 146.8 COMPAQ BD1468856B HPB2 AAA1P4C02C680449 1 5 0 1 13 146.8 COMPAQ BD146863B3 HPB5 B8LY5HXM 1 8 0 1 14 146.8 COMPAQ BD146863B3 HPB5 B8P95H4M 2 0 0 2 1 300.0 COMPAQ BD30089BBA HPB1 DA01P720AMNM0705 2 1 0 2 2 300.0 COMPAQ BD30089BBA HPB1 DA01P710AFC60705 2 2 0 2 3 300.0 COMPAQ BD30089BBA HPB1 DA01P720AMNR0705 2 3 0 2 4 300.0 COMPAQ BD30089BBA HPB1 DA01P710AFEM0705 2 4 0 2 5 72.8 COMPAQ BD07289BB8 HPB1 DAL1P670DUFY0629 2 5 0 2 6 72.8 COMPAQ BD0728A4C4 HPB4 3KT5RQFR00009717XDH6 2 8 0 2 7 72.8 COMPAQ BD0728A4C4 HPB4 3KT5H59N0000765286JP 2 9 0 2 8 72.8 COMPAQ BD0728A4C4 HPB4 3KT5QLX700009717VCBA 2 10 0 2 9 72.8 COMPAQ BD0728A4C4 HPB4 3KT5H33900009714ULQ8 2 11 0 2 10 72.8 COMPAQ BD0728A4C4 HPB4 3KT5RVF50000971756KN 2 12 0 2 11 72.8 COMPAQ BD0728A4C4 HPB4 3KT5QNX600009716UJ1H 2 13 0 2 12 72.8 COMPAQ BD0728A4C4 HPB4 3KT5RRYH00009717XD38 2 14 0 2 13 72.8 COMPAQ BD0728A4C4 HPB4 3KT5RRT0000097174XL4 2 15 0 2 14 72.8 COMPAQ BD0728A4C4 HPB4 3KT5QPQY00009716QXR2 CLI-2> show profile Profile name = Default (Default) Mode value = (00002405) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Ignore Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode Profile name = Windows Type = Standard Mode value = (00002405) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Ignore Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode Profile name = Windows (degraded performance) Type = Standard Mode value = (00003405) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode Profile name = OpenVMS Type = Standard Mode value = (00003473) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = VMS shadow style bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode Profile name = Tru64 Type = Standard Mode value = (00003563) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode Profile name = Linux Type = Standard Mode value = (000034a7) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode Profile name = Solaris Type = Standard Mode value = (000034a7) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode Profile name = Netware Type = Standard Mode value = (000034a7) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode Profile name = HP Type = Standard Mode value = (00003ca6) Mode 0 = Volume Set Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = No Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode Profile name = XP Storage Array Type = Standard Mode value = (00003563) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='HP' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Admit Target Port on Reservation Mode 14 = Asymmetrical Active/Active Operating Mode CLI-2> show globals Global Parameters: System Name: Rebuild Priority: high Expand Priority: medium Surface Delay: 3.0 seconds Total Cache: 256MB 50% Read Cache: 128MB 50% Write Cache: 128MB Temperature: No temperature sensor support. FIBRE BAY: 30 Celsius, 86 Fahrenheit CLI-2> show acl ACL is enabled: Connection WWPN Units ILEXCH2 10000000-C963C3CE 0, 4 unknown 10000000-C93AE557 1 ILGRAPH2 10000000-C94253C9 3 ILGRAPH1 210000E0-8B859CE3 3 ILSERVDATA 210000E0-8B1EB7EB 2 SWSILSRV2 210000E0-8B8552E3 1 SWSILSRV1 210000E0-8B1E09DD 1 ILEXCH1 10000000-C94253C3 0, 4 Inaccessible Units: None CLI-2> show connections Connection Name: SWSILSRV1 Host WWNN = 200000E0-8B1E09DD Host WWPN = 210000E0-8B1E09DD Profile Name = Windows Unit Offset = 0 Controller 2 Port 1 Status = Online Controller 1 Port 1 Status = Offline Connection Name: ILEXCH1 Host WWNN = 20000000-C94253C3 Host WWPN = 10000000-C94253C3 Profile Name = Default Unit Offset = 0 Controller 2 Port 1 Status = Online show disks Controller 1 Port 1 Status = Offline Connection Name: ILGRAPH2 Host WWNN = 20000000-C94253C9 Host WWPN = 10000000-C94253C9 Profile Name = Default Unit Offset = 0 Controller 2 Port 1 Status = Online Disk List: (box,bay) (B:T:L) Size Speed Units show boxEnclosure 1: SCSI (0:07:00) PROLIANT 4L7I DB1.86 Disk101 (1,01) (0:00:00) 300.0GB 160 MB/s 2 Disk102 (1,02) (0:01:00) 300.0GB 160 MB/s 2 Disk103 (1,03) (0:02:00) 300.0GB 160 MB/s 2 Disk104 (1,04) (0:03:00) 300.0GB 160 MB/s 2 Disk105 (1,05) (0:04:00) 300.0GB 160 MB/s 2 Disk106 (1,06) (0:05:00) 300.0GB 160 MB/s 2 Disk109 (1,09) (1:01:00) 146.8GB 160 MB/s 0 Disk110 (1,10) (1:02:00) 146.8GB 160 MB/s 0 Disk111 (1,11) (1:03:00) 146.8GB 160 MB/s 0 Disk112 (1,12) (1:04:00) 146.8GB 160 MB/s 0 Disk113 (1,13) (1:05:00) 146.8GB 160 MB/s 0 Disk114 (1,14) (1:08:00) 146.8GB 160 MB/s 0 Enclosure 2: SCSI (2:07:00) PROLIANT 4LEE CP20 Disk201 (2,01) (2:00:00) 300.0GB 160 MB/s 3 Disk202 (2,02) (2:01:00) 300.0GB 160 MB/s 3 Disk203 (2,03) (2:02:00) 300.0GB 160 MB/s 3 Disk204 (2,04) (2:03:00) 300.0GB 160 MB/s 3 Disk205 (2,05) (2:04:00) 72.8GB 160 MB/s 4 Disk206 (2,06) (2:05:00) 72.8GB 160 MB/s 4 Disk207 (2,07) (2:08:00) 72.8GB 160 MB/s 1 Disk208 (2,08) (2:09:00) 72.8GB 160 MB/s 1 Disk209 (2,09) (2:10:00) 72.8GB 160 MB/s 1 Disk210 (2,10) (2:11:00) 72.8GB 160 MB/s 1 Disk211 (2,11) (2:12:00) 72.8GB 160 MB/s 1 Disk212 (2,12) (2:13:00) 72.8GB 160 MB/s 1 Disk213 (2,13) (2:14:00) 72.8GB 160 MB/s 1 Disk214 (2,14) (2:15:00) 72.8GB 160 MB/s 1 Notes: The speed is the currently negotiated speed to the disk. This may be less than the maximum speed supported by the device due to bus faults, loss of signal integrity, etc. Box #2: SCSI enclosure at bus 2 channel 0 target 7 Firmware ID string: PROLIANT 4LEE Firmware revision: CP20 Serial number: M0CNLMPX5F Environmental Status: Redundant power supply not present Controller 1 Port 1 Status = Offline Connection Name: RBNNT Host WWNN = 20000000-C94013D1 Host WWPN = 10000000-C94013D1 Profile Name = Windows Unit Offset = 0 Controller 2 Port 1 Status = Offline show units Controller 1 Port 1 Status = Online Connection Name: ILSERVDATA Host WWNN = 200000E0-8B1EB7EB Host WWPN = 210000E0-8B1EB7EB Profile Name = Windows Unit Offset = 0 Controller 2 Port 1 Status = Offline Unit 0: show this_controllerIn PDLA mode, Unit 0 is Lun 1; In VSA mode, Unit 0 is Lun 0. Unit Identifier : Device Identifier : 600805F3-0012D8D0-A6EBA9D0-1D070004 Preferred Path : Controller 1 (other controller) Cache Status : Enabled Max Boot Partition: Disabled Volume Status : VOLUME OK Mirror Init Status: Complete 6 Data Disk(s) used by lun 0: Disk109: Box 1, Bay 09, (B:T:L 1:01:00) Disk110: Box 1, Bay 10, (B:T:L 1:02:00) Disk111: Box 1, Bay 11, (B:T:L 1:03:00) Disk112: Box 1, Bay 12, (B:T:L 1:04:00) Disk113: Box 1, Bay 13, (B:T:L 1:05:00) Disk114: Box 1, Bay 14, (B:T:L 1:08:00) Spare Disk(s) used by lun 0: No spare drive is designated. Logical Volume Raid Level: MIRROR FAULT TOLERANCE (RAID 1) stripe_size=128kB Logical Volume Capacity : 420,041MB Unit 1: In PDLA mode, Unit 1 is Lun 2; In VSA mode, Unit 1 is Lun 1. Unit Identifier : Device Identifier : 600805F3-0012D8D0-A2A316E4-FA400006 Preferred Path : Controller 1 (other controller) Cache Status : Enabled Max Boot Partition: Disabled Volume Status : VOLUME OK Parity Init Status: Complete 8 Data Disk(s) used by lun 1: Disk207: Box 2, Bay 07, (B:T:L 2:08:00) Disk208: Box 2, Bay 08, (B:T:L 2:09:00) Disk209: Box 2, Bay 09, (B:T:L 2:10:00) Disk210: Box 2, Bay 10, (B:T:L 2:11:00) Disk211: Box 2, Bay 11, (B:T:L 2:12:00) Disk212: Box 2, Bay 12, (B:T:L 2:13:00) Disk213: Box 2, Bay 13, (B:T:L 2:14:00) Disk214: Box 2, Bay 14, (B:T:L 2:15:00) Spare Disk(s) used by lun 1: No spare drive is designated. Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5) stripe_size=64kB Logical Volume Capacity : 486,250MB Unit 2: In PDLA mode, Unit 2 is Lun 3; In VSA mode, Unit 2 is Lun 2. Unit Identifier : Device Identifier : 600805F3-0012D8D0-AE443DC2-4A380007 Preferred Path : Controller 1 (other controller) Cache Status : Enabled Max Boot Partition: Disabled Volume Status : VOLUME OK Parity Init Status: Complete 6 Data Disk(s) used by lun 2: Disk101: Box 1, Bay 01, (B:T:L 0:00:00) Disk102: Box 1, Bay 02, (B:T:L 0:01:00) Disk103: Box 1, Bay 03, (B:T:L 0:02:00) Disk104: Box 1, Bay 04, (B:T:L 0:03:00) Disk105: Box 1, Bay 05, (B:T:L 0:04:00) Disk106: Box 1, Bay 06, (B:T:L 0:05:00) Spare Disk(s) used by lun 2: No spare drive is designated. Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5) stripe_size=64kB Logical Volume Capacity : 1,430,508MB Unit 3: In PDLA mode, Unit 3 is Lun 4; In VSA mode, Unit 3 is Lun 3. Unit Identifier : Device Identifier : 600805F3-00059EA0-A7EA9555-5DAD0006 Preferred Path : Controller 2 (this controller) Cache Status : Enabled Max Boot Partition: Enabled Volume Status : VOLUME OK Parity Init Status: Complete 4 Data Disk(s) used by lun 3: Disk201: Box 2, Bay 01, (B:T:L 2:00:00) Disk202: Box 2, Bay 02, (B:T:L 2:01:00) Disk203: Box 2, Bay 03, (B:T:L 2:02:00) Disk204: Box 2, Bay 04, (B:T:L 2:03:00) Spare Disk(s) used by lun 3: No spare drive is designated. Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5) stripe_size=16kB Logical Volume Capacity : 858,305MB Unit 4: In PDLA mode, Unit 4 is Lun 5; In VSA mode, Unit 4 is Lun 4. Unit Identifier : Device Identifier : 600805F3-00059EA0-A5651E25-EE180007 Preferred Path : Controller 1 (other controller) Cache Status : Enabled Max Boot Partition: Disabled Volume Status : VOLUME OK Mirror Init Status: Complete 2 Data Disk(s) used by lun 4: Disk205: Box 2, Bay 05, (B:T:L 2:04:00) Disk206: Box 2, Bay 06, (B:T:L 2:05:00) Spare Disk(s) used by lun 4: No spare drive is designated. Logical Volume Raid Level: MIRROR FAULT TOLERANCE (RAID 1) stripe_size=128kB Logical Volume Capacity : 69,463MB Controller 2 (left controller): MSA1000(c) Hewlett-Packard P56350DX3PT00Z Version 7.00 Build 1500 Hardware 7 Build Time: 2007-01-24 16:13:17 Integrated Enclosure. Controller Identifier: NODE_ID = 500805F3-0012D8D0 SCSI_VERSION = SCSI-3 Supported Redundancy Mode: Active/Standby Asym-Active/Active Current Redundancy Mode: Asym-Active/Active Device Port SCSI address 7 Terminal speed for the CLI is set to 19200. Host Port_1: REPORTED PORT_ID 500805F3-0012D8D9 PORT_1_TOPOLOGY = F_Port Cache: 128 megabyte read cache 128 megabyte write cache Version 2 Cache is GOOD, and Cache is enabled. No unflushed data in cache Batteries are disabled Module #1 is fully charged and turned off. Controller Up Time: 218 Days 06 Hours 36 Minutes 26 Seconds Health: Surface Scan: Complete. Rebuild Status: Complete. Expansion: Complete. Controller 1 Port 1 Status = Online Connection Name: ILGRAPH1 Host WWNN = 200000E0-8B859CE3 Host WWPN = 210000E0-8B859CE3 Profile Name = Windows Unit Offset = 0 Controller 2 Port 1 Status = Offline show other_controller Controller 1 Port 1 Status = Online Connection Name: SWSILSRV2 Host WWNN = 200000E0-8B8552E3 Host WWPN = 210000E0-8B8552E3 Profile Name = Windows Unit Offset = 0 Controller 2 Port 1 Status = Offline show eventlog Controller 1 Port 1 Status = Online Connection Name: ILEXCH2 Host WWNN = 20000000-C963C3CE Host WWPN = 10000000-C963C3CE Profile Name = Windows Unit Offset = 0 Controller 2 Port 1 Status = Offline Controller 1 (right controller): MSA1000(c) Hewlett-Packard P56350GX3QN0CO Version 7.00 Build 1500 Hardware A Build Time: 2007-01-24 16:13:17 Integrated Enclosure. Controller Identifier: NODE_ID = 500805F3-0012D8D0 SCSI_VERSION = SCSI-3 Supported Redundancy Mode: Active/Standby Asym-Active/Active Current Redundancy Mode: Asym-Active/Active Device Port SCSI address 6 Terminal speed for the CLI is set to 19200. Host Port_1: REPORTED PORT_ID 500805F3-0012D8D1 PORT_1_TOPOLOGY = F_Port Cache: 128 megabyte read cache 128 megabyte write cache Version 2 Cache is GOOD, and Cache is enabled. No unflushed data in cache Batteries are disabled Module #1 is fully charged and turned off. Controller Up Time: 218 Days 06 Hours 18 Minutes 16 Seconds Health: Surface Scan: Complete. Rebuild Status: Complete. Expansion: Complete. show preferred_path Controller 1 Port 1 Status = Online Connection Name: CLI-2> bad show auto_path_change Host WWNN = 10000000-C93216B7 Host WWPN = 10000000-C93216B7 Profile Name = Windows Unit Offset = 0 Implicit (automatic load-based) LUN ownership changes are currently ENABLED. Implicit LUN ownership change preferences are as follows: Minimum % of proxied requests to trigger implicit path change..: 75% Minimum number of requests to LUN before path change enabled...: 65536 Minimum time to wait before changing ownership after power-up..: 30 minutes Minimum time between ownership changes for LUN.................: 30 minutes Connection Name: bad Host WWNN = 10000000-C932175E Host WWPN = 10000000-C932175E Profile Name = Windows Unit Offset = 0 Connection Name: unknown Host WWNN = 10000000-C93AE557 Host WWPN = 10000000-C93AE557 Profile Name = Windows Unit Offset = 0 CLI-2>