-->正常开机后: Firmware Version 5.0 Duplex Console IO Dependent Code (IODC) revision 1 ------------------------------------------------------------------------------ (c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved ------------------------------------------------------------------------------ Processor Speed State Coprocessor State I/D Cache --------- -------- --------------------- ----------------- ------------- 0 400 MHz Active Functional 512 kB/1 MB Central Bus Speed: 120 MHz Available memory: 1073741824 bytes Good memory required: 42999808 bytes Primary boot path: SCSI.5.0 Alternate boot path: SCSI.5.0 Console path: SERIAL_1.9600.8.none Keyboard path: USB Processor is booting from first available device. To discontinue, press any key within 10 seconds. 10 seconds expired. Proceeding... Searching for device(s) with bootable media... This may take several minutes. To discontinue search, press any key (termination may not be immediate). Attempting to boot Primary Path... BOOTABLE DEVICE FOUND: Path Number Device Path Device Type and Utilities ----------- ----------------- ------------------------- P0 SCSI.5.0 QUANTUM Atlas4-9LVD IPL Booting... Boot IO Dependent Code (IODC) revision 0 HARD Booted. ISL Revision A.00.38 OCT 26, 1994 ISL booting hpux Boot : disk(10/0/15/0.5.0.0.0.0.0;0)/stand/vmunix 7073792 + 871000 + 753040 start 0x21ba68 gate64: sysvec_vaddr = 0xc0002000 for 1 pages NOTICE: autofs_link(): File system was registered at index 3. NOTICE: nfs3_link(): File system was registered at index 5. System Console is on the Built-In Serial Interface Logical volume 64, 0x3 configured as ROOT Logical volume 64, 0x2 configured as SWAP Logical volume 64, 0x2 configured as DUMP Swap device table: (start & size given in 512-byte blocks) entry 0 - major is 64, minor is 0x2; start = 0, size = 1048576 Starting the STREAMS daemons-phase 1 Checking root file system. file system is clean - log replay is not required Root check done. Create STCP device files B2352B/9245XB HP-UX (B.11.00) #1: Wed Nov 5 22:38:19 PST 1997 Memory Information: physical page size = 4096 bytes, logical page size = 4096 bytes Physical: 1048576 Kbytes, lockable: 747968 Kbytes, available: 869184 Kbytes /sbin/ioinitrc: /sbin/bcheckrc: Checking for LVM volume groups and Activating (if any exist) Volume group "/dev/vg00" has been successfully changed. Activated volume group Volume group "/dev/vg01" has been successfully changed. Resynchronized volume group /dev/vg00 Resynchronized volume group /dev/vg01 vxfs fsck: sanity check: root file system OK (mounted read/write) Checking hfs file systems /sbin/fsclean: /dev/vg00/lvol1 (mounted) ok HFS file systems are OK, not running fsck Checking vxfs file systems /dev/vg00/lvol8 : vxfs fsck: sanity check: /dev/vg00/lvol8 OK /dev/vg01/lvol1 : vxfs fsck: sanity check: /dev/vg01/lvol1 OK /dev/vg00/lvol3 : vxfs fsck: sanity check: root file system OK (mounted read/write) /dev/vg00/lvol4 : vxfs fsck: sanity check: /dev/vg00/lvol4 OK /dev/vg00/lvol5 : vxfs fsck: sanity check: /dev/vg00/lvol5 OK /dev/vg00/lvol6 : vxfs fsck: sanity check: /dev/vg00/lvol6 OK /dev/vg00/lvol7 : vxfs fsck: sanity check: /dev/vg00/lvol7 OK (c)Copyright 1983-1997 Hewlett-Packard Co., All Rights Reserved. (c)Copyright 1979, 1980, 1983, 1985-1993 The Regents of the Univ. of California (c)Copyright 1980, 1984, 1986 Novell, Inc. (c)Copyright 1986-1992 Sun Microsystems, Inc. (c)Copyright 1985, 1986, 1988 Massachusetts Institute of Technology (c)Copyright 1989-1993 The Open Software Foundation, Inc. (c)Copyright 1986 Digital Equipment Corp. (c)Copyright 1990 Motorola, Inc. (c)Copyright 1990, 1991, 1992 Cornell University (c)Copyright 1989-1991 The University of Maryland (c)Copyright 1988 Carnegie Mellon University (c)Copyright 1991-1997 Mentat, Inc. (c)Copyright 1996 Morning Star Technologies, Inc. (c)Copyright 1996 Progressive Systems, Inc. (c)Copyright 1997 Isogon Corporation RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in sub-paragraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause in DFARS 252.227-7013. Hewlett-Packard Company 3000 Hanover Street Palo Alto, CA 94304 U.S.A. Rights for non-DOD U.S. Government Departments and Agencies are as set forth in FAR 52.227-19(c)(1,2). /sbin/auto_parms: DHCP access is disabled (see /etc/auto_parms.log) _______________________________________________________________________________ Welcome to HP-UX! Before using your system, you will need to answer a few questions. The first question is whether you plan to use this system on a network. Answer "yes" if you have connected the system to a network and are ready to link with a network. Answer "no" if you: * Plan to set up this system as a standalone (no networking). * Want to use the system now as a standalone and connect to a network later. _______________________________________________________________________________ Are you ready to link this system to a network? Press [y] for yes or [n] for no, then press [Return] n _______________________________________________________________________________ If your network contains a DHCP (Dynamic Host Configuration Protocol) server, you may want to use the DHCP server to supply your networking setup information. It is best to answer "Yes" to the following question only if you're sure that DHCP service is available. _______________________________________________________________________________ Do you wish to use DHCP to obtain networking information? Press [y] for yes or [n] for no, then press [Return] n _______________________________________________________________________________ Before you begin using this system, you need to obtain the following information from your local network administrator: * Your system name (host name). * Your time zone. If you do not have this information, you may stop now and restart your system once you have it. _______________________________________________________________________________ Do you wish to continue (answering no will HALT the system)? Press [y] for yes or [n] for no, then press [Return] y _______________________________________________________________________________ For the system to operate correctly, you must assign it a unique system name or "hostname". The hostname can be a simple name (example: widget) or an Internet fully-qualified domain name (example: widget.redrock-cvl.hp.com). A simple name, or each dot (.) separated component of a domain name, must: * Start with a letter. * Contain no more than 64 characters. * Contain only letters, numbers, underscore (_), or dash (-). Uppercase letters are not recommended. NOTE: The first or only component of a hostname should contain 8 characters or less for compatibility with HP-UX `uname'. The current hostname is b2000. _______________________________________________________________________________ Enter the system name, then press [Return] or simply press [Return] to retain the current host name (b2000): You have chosen b2000 as the name for this system. Is this correct? Press [y] for yes or [n] for no, then press [Return] y _______________________________________________________________________________ Working... _______________________________________________________________________________ _______________________________________________________________________________ The following procedure enables you to set the time zone. Select your location from the following list: 1) North America or Hawaii 2) Central America 3) South America 4) Europe 5) Africa 6) Asia 7) Australia, New Zealand _______________________________________________________________________________ Enter the number for your location (1-7) then press [Enter] 6 _______________________________________________________________________________ Select your time zone from the following list: 1) Saudi Arabia, Syria | 6) Phillipines, Hong Kong, Eastern China, Taiwan | 2) India | 7) Japan | 3) Pakistan | 8) Korea | 4) Thailand | 9) Unlisted time zone | 5) Singapore | 10) Previous menu _______________________________________________________________________________ Enter the number for your time zone (1 - 10), then press [Enter] 6 _______________________________________________________________________________ You have selected: Phillipines, Hong Kong, Eastern China, Taiwan (EAT-8). _______________________________________________________________________________ Is this correct? Press [y] for yes or [n] for no, then press [Return] y _______________________________________________________________________________ This section enables you to set the system clock. _______________________________________________________________________________ The current system time is Wed Oct 19 11:10:04 2005 Is this correct? Press [y] for yes or [n] for no, then press [Return] y _______________________________________________________________________________ Note: As installed, your system does not have all of its disk space available for immediate use. If this system was factory installed, this was done to allow flexibility in configuring your system. You may use the LVM (Logical Volume Manager) portion of SAM to allocate more disk space for your use. You currently have a total of 11204 megabytes of disk space unallocated in 2 Logical Volume group(s). After the system has finished starting up, you may run /usr/sbin/sam to allocate this space to your needs. _______________________________________________________________________________ Press [Return] to continue... _______________________________________________________________________________ Congratulations! Your system is now configured as a standalone system with the system name b2000! After you have obtained a network Internet address from your network administrator, and connected this system to a network, type this command (you may want to note this for later reference): /sbin/set_parms ip_address [Return] To set up additional network parameters for routing, DNS, and NIS, type: /sbin/set_parms addl_netwrk [Return] To fully utilize the capabilities of your system, you may have to perform some additional system configuration tasks using the HP-UX "sam" (System Administration Manager) command. Consult your local administrator or the "HP-UX System Administration Tasks" manual for more information. The system will now complete its boot process, and allow you to login as 'root'. _______________________________________________________________________________ Press [Return] to continue... HP-UX Start-up in progress __________________________ Configure system crash dumps .............................. OK Mount file systems ........................................ OK Update kernel and loadable modules ........................ N/A Initialize loadable modules ............................... OK Setting hostname .......................................... OK Set privilege group ....................................... N/A Display date .............................................. N/A Copy processor logs to /var/tombstones .................... OK Save system crash dump if needed .......................... N/A Enable auxiliary swap space ............................... OK Start syncer daemon ....................................... OK Configure HP Fibre Channel interfaces ..................... OK Configure Loopback interfaces (lo0) ....................... OK Initialize Software Distributor agent daemon .............. N/A Configuring all unconfigured software filesets ............ OK Recover editor crash files ................................ OK Clean UUCP ................................................ OK List and/or clear temporary files ......................... N/A Clean up old log files .................................... OK Start system message logging daemon ....................... OK Start pty allocator daemon ................................ OK Start network tracing and logging daemon .................. OK Configure HP Ethernet interfaces .......................... OK Configure HP 100BT interfaces ............................. OK Configure HP SPP 100BT interfaces ......................... N/A Configure LAN interfaces .................................. OK Start name server daemon .................................. N/A Start NFS core subsystem .................................. OK Start NIS+ server subsystem ............................... OK Start NIS+ client subsystem ............................... OK Start NIS server subsystem ................................ OK Start NIS client subsystem ................................ OK Start NFS client subsystem ................................ OK Start the Trusted Mode with Nis+ subsystem ................ N/A Configure pseudo devices for MAC/LLA access ............... OK Start multicast routing daemon ............................ N/A Start Internet services daemon ............................ OK Start dynamic routing daemon .............................. N/A Start router discover protocol daemon ..................... N/A Configuring PPP Interface ................................. OK Start RARP protocol daemon ................................ N/A Start remote system status daemon ......................... N/A Configuring man pages for Internet Services ............... OK Starting mail daemon ...................................... OK Starting outbound connection daemons for DDFA software .... N/A Start SNMP Master Network Management daemon ............... OK Start OSPF MIB Network Management subAgent ................ N/A Start SNMP HP-UNIX Network Management subAgent ............ OK Start SNMP MIB-2 Network Management subAgent .............. OK Start SNMP Trap Dest Network Management subAgent .......... OK Start HA cluster SNMP subagent ............................ OK Start DCE daemons ......................................... N/A Start RPC daemon if needed ................................ FAIL * Start the Isogon License Server daemon .................... N/A Starting ISEE hpservices mad daemon. ...................... OK Start Runner .............................................. OK Start remote boot daemon .................................. OK Starting X Font Server at TCP port 7000 ................... N/A Start vt daemon ........................................... OK Start time synchronization ................................ N/A Start accounting .......................................... N/A Install/Load XF86 DLKM Helper Modules ..................... OK Starting the password/group assist subsystem .............. OK Starting HP Disk Array Manager daemons. ................... OK Starting disk array monitor daemons. ...................... OK Start print spooler ....................................... N/A Starting HP Distributed Print Service ..................... OK Start clock daemon ........................................ OK Support Tools Informational Fileset ....................... OK Start diagnostic subsystem ................................ OK Start auditing subsystem .................................. N/A Start audio server daemon ................................. OK Start Distributed Single Logical Screen daemon ............ OK SAM System administration configuration ................... OK MeasureWare performance software is being started. ........ OK Initialize Software Distributor agent daemon .............. OK Copy processor logs to /var/tombstones .................... OK Starting Event Monitoring Service ......................... OK Start EMS SNMP subagent ................................... OK Configure HP Fibre Channel Mass Storage interfaces ........ OK Starting the RST EMS listener ............................. OK Start NFS server subsystem ................................ OK Start X print server(s) ................................... N/A Start Highly Available cluster ............................ N/A .......................................................... OK Start CDE login server .................................... N/A * - An error has occurred ! * - Refer to the file /etc/rc.log for more information. -->必须要配置DHCP后才能启动到系统 The system is ready. GenericSysName [HP Release B.11.00] (see /etc/issue) Console Login: root Password: Login incorrect login: root Password: Login incorrect login: root Password: Please wait...checking for disk quotas (c)Copyright 1983-1997 Hewlett-Packard Co., All Rights Reserved. (c)Copyright 1979, 1980, 1983, 1985-1993 The Regents of the Univ. of California (c)Copyright 1980, 1984, 1986 Novell, Inc. (c)Copyright 1986-1992 Sun Microsystems, Inc. (c)Copyright 1985, 1986, 1988 Massachusetts Institute of Technology (c)Copyright 1989-1993 The Open Software Foundation, Inc. (c)Copyright 1986 Digital Equipment Corp. (c)Copyright 1990 Motorola, Inc. (c)Copyright 1990, 1991, 1992 Cornell University (c)Copyright 1989-1991 The University of Maryland (c)Copyright 1988 Carnegie Mellon University (c)Copyright 1991-1997 Mentat, Inc. (c)Copyright 1996 Morning Star Technologies, Inc. (c)Copyright 1996 Progressive Systems, Inc. (c)Copyright 1997 Isogon Corporation RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in sub-paragraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause in DFARS 252.227-7013. Hewlett-Packard Company 3000 Hanover Street Palo Alto, CA 94304 U.S.A. Rights for non-DOD U.S. Government Departments and Agencies are as set forth in FAR 52.227-19(c)(1,2). You have mail. unknown mode: -i (这是以前就有的) Value of TERM has been set to "vt100". WARNING: YOU ARE SUPERUSER !! -->查看网卡的地址不见了 # ifconfig lan0 ifconfig: no such interface -->扫描网卡的状态,是up的 # lanscan Hardware Station Crd Hdw Net-Interface NM MAC HP-DLPI DLPI Path Address In# State NamePPA ID Type Support Mjr# 10/0/12/0 0x001083F9F4F4 0 UP lan0 snap0 1 ETHER Yes 119 # netstat -in Name Mtu Network Address Ipkts Opkts lo0 4136 127.0.0.0 127.0.0.1 913 913 # netstat -rn Routing tables Dest/Netmask Gateway Flags Refs Use Interface Pmtu 127.0.0.1 127.0.0.1 UH 0 913 lo0 4136 127.0.0.0 127.0.0.1 U 0 0 lo0 4136 # ps -ef|grep inetd root 906 1 0 11:12:05 ? 0:00 /usr/sbin/inetd -->查看系统里面的服务,正常 # more /etc/services # @(#)services $Revision: 1.32.214.7 $ $Date: 97/09/10 14:50:42 $ # # This file associates official service names and aliases with # the port number and protocol the services use. # # Some of the services represented below are not supported on HP-UX. # They are provided solely as a reference. # # The form for each entry is: # # # See the services(4) manual page for more information. # Note: The entries cannot be preceded by a blank space. # tcpmux 1/tcp # TCP port multiplexer (RFC 1078) echo 7/tcp # Echo echo 7/udp # discard 9/tcp sink null # Discard discard 9/udp sink null # systat 11/tcp users # Active Users daytime 13/tcp # Daytime daytime 13/udp # qotd 17/tcp quote # Quote of the Day chargen 19/tcp ttytst source # Character Generator chargen 19/udp ttytst source # ftp-data 20/tcp # File Transfer Protocol (Data) ftp 21/tcp # File Transfer Protocol (Control) telnet 23/tcp # Virtual Terminal Protocol smtp 25/tcp # Simple Mail Transfer Protocol time 37/tcp timeserver # Time time 37/udp timeserver # rlp 39/udp resource # Resource Location Protocol whois 43/tcp nicname # Who Is domain 53/tcp nameserver # Domain Name Service domain 53/udp nameserver # bootps 67/udp # Bootstrap Protocol Server bootpc 68/udp # Bootstrap Protocol Client tftp 69/udp # Trivial File Transfer Protocol rje 77/tcp netrjs # private RJE Service finger 79/tcp # Finger http 80/tcp www # World Wide Web HTTP http 80/udp www # World Wide Web HTTP link 87/tcp ttylink # private terminal link supdup 95/tcp # hostnames 101/tcp hostname # NIC Host Name Server tsap 102/tcp iso_tsap iso-tsap # ISO TSAP (part of ISODE) pop 109/tcp postoffice pop2 # Post Office Protocol - Version 2 pop3 110/tcp pop-3 # Post Office Protocol - Version 3 portmap 111/tcp sunrpc # SUN Remote Procedure Call portmap 111/udp sunrpc # ident 113/tcp authentication # RFC1413 sftp 115/tcp # Simple File Transfer Protocol uucp-path 117/tcp # UUCP Path Service nntp 119/tcp readnews untp # Network News Transfer Protocol ntp 123/udp # Network Time Protocol netbios_ns 137/tcp # NetBIOS Name Service netbios_ns 137/udp # netbios_dgm 138/tcp # NetBIOS Datagram Service netbios_dgm 138/udp # netbios_ssn 139/tcp # NetBIOS Session Service netbios_ssn 139/udp # bftp 152/tcp # Background File Transfer Protocol snmp 161/udp snmpd # Simple Network Management Protocol Agent snmp-trap 162/udp trapd # Simple Network Management Protocol Traps bgp 179/tcp # Border Gateway Protocol # PV performance tool services entries pvserver 382/tcp # PV server pvalarm 383/tcp # PV alarm management # # UNIX services # biff 512/udp comsat # mail notification exec 512/tcp # remote execution, passwd required login 513/tcp # remote login who 513/udp whod # remote who and uptime shell 514/tcp cmd # remote command, no passwd used syslog 514/udp # remote system logging printer 515/tcp spooler # remote print spooling talk 517/udp # conversation ntalk 518/udp # new talk, conversation route 520/udp router routed # routing information protocol efs 520/tcp # Extended file name server timed 525/udp timeserver # remote clock synchronization tempo 526/tcp newdate # courier 530/tcp rpc # conference 531/tcp chat # netnews 532/tcp readnews # netwall 533/udp # Emergency broadcasting uucp 540/tcp uucpd # uucp daemon remotefs 556/tcp rfs_server rfs # Brunhoff remote filesystem ingreslock 1524/tcp # # # Other HP-UX services # lansrm 570/udp # SRM/UX Server DAServer 987/tcp # SQL distributed access instl_boots 1067/udp # installation bootstrap protocol server instl_bootc 1068/udp # installation bootstrap protocol client nfsd-keepalive 1110/udp # Client status info nfsd-status 1110/tcp # Cluster status info msql 1111/tcp # Mini SQL database server rlb 1260/tcp # remote loopback diagnostic clvm-cfg 1476/tcp # HA LVM configuration diagmond 1508/tcp # Diagnostic System Manager nft 1536/tcp # NS network file transfer sna-cs 1553/tcp # SNAplus client/server sna-cs 1553/udp # SNAplus client/server ncpm-pm 1591/udp # NCPM Policy Manager ncpm-hip 1683/udp # NCPM Host Information Provider cvmon 1686/udp # Clusterview cvmon-cvmap communication registrar 1712/tcp # resource monitoring service registrar 1712/udp # resource monitoring service ncpm-ft 1744/udp # NCPM File Transfer psmond 1788/tcp # Predictive Monitor psmond 1788/udp # Hardware Predictive Monitor pmlockd 1889/tcp # SynerVision locking daemon pmlockd 1889/udp # nfsd 2049/udp # NFS remote file system nfsd 2049/tcp # NFS remote file system netdist 2106/tcp # update(1m) network distribution service rfa 4672/tcp # NS remote file access veesm 4789/tcp # HP VEE service manager hacl-hb 5300/tcp # High Availability (HA) Cluster heartbeat hacl-gs 5301/tcp # HA Cluster General Services hacl-cfg 5302/tcp # HA Cluster TCP configuration hacl-cfg 5302/udp # HA Cluster UDP configuration hacl-probe 5303/tcp # HA Cluster TCP probe hacl-probe 5303/udp # HA Cluster UDP probe hacl-local 5304/tcp # HA Cluster Commands hacl-test 5305/tcp # HA Cluster Test hacl-dlm 5408/tcp # HA Cluster distributed lock manager lanmgrx.osB 5696/tcp # LAN Manager/X for B.00.00 OfficeShare r4-sna-cs 5707/tcp # SNA client/server (up to Release 4.1) SNAplus 5708/udp # SNA logical network A (up to Release 4.1) r4-sna-ft 5709/tcp # SNA file transfer (up to Release 4.1) hcserver 5710/tcp # HP Cooperative Services grmd 5999/tcp # graphics resource manager spc 6111/tcp # sub-process control desmevt 6868/tcp # DE/ Services Monitor, Event Service pdclientd 6874/tcp # Palladium print client daemon pdeventd 6875/tcp # Palladium print event daemon iasqlsvr 7489/tcp # Information Access recserv 7815/tcp # SharedX Receiver Service ftp-ftam 8868/tcp # FTP->FTAM Gateway mcsemon 9999/tcp # MC/System Environment monitor console 10000/tcp # MC/System Environment console multiplexor actcp 31766/tcp # ACT Call Processing Server # # Kerberos (Project Athena/MIT) services # kerberos5 88/udp kdc # Kerberos 5 kdc klogin 543/tcp # Kerberos rlogin -kfall kshell 544/tcp krcmd # Kerberos remote shell -kfall ekshell 545/tcp krcmd # Kerberos encrypted remote shell -kfall kerberos 750/udp kdc # Kerberos (server) udp -kfall kerberos 750/tcp kdc # Kerberos (server) tcp -kfall kerberos_master 751/tcp kadmin # Kerberos kadmin krbupdate 760/tcp kreg # Kerberos registration -kfall kpasswd 761/tcp kpwd # Kerberos "passwd" -kfall eklogin 2105/tcp # Kerberos encrypted rlogin -kfall # The X10_LI server for each display listens on ports 5800 + display number. # The X10_MI server for each display listens on ports 5900 + display number. # The X11 server for each display listens on ports 6000 + display number. # The X11 font server listens on port 7000. # Do NOT associate other services with these ports. # Refer to the X documentation for details. hpoms-ci-lstn 5403/tcp #SAP spooler support hpoms-dps-lstn 5404/tcp #SAP spooler support samd 3275/tcp # sam daemon dtspc 6112/tcp #subprocess control -->查看inetd.conf文件,也正常 # more /etc/inetd.conf ## Configured using SAM by root on Wed Sep 28 21:05:18 2005 ## # # @(#)inetd.conf $Revision: 1.24.214.3 $ $Date: 97/09/10 14:50:49 $ # # Inetd reads its configuration information from this file upon execution # and at some later time if it is reconfigured. # # A line in the configuration file has the following fields separated by # tabs and/or spaces: # # service name as in /etc/services # socket type either "stream" or "dgram" # protocol as in /etc/protocols # wait/nowait only applies to datagram sockets, stream # sockets should specify nowait # user name of user as whom the server should run # server program absolute pathname for the server inetd will # execute # server program args. arguments server program uses as they normally # are starting with argv[0] which is the name of # the server. # # See the inetd.conf(4) manual page for more information. ## ## # # ARPA/Berkeley services # ## ftp stream tcp nowait root /usr/lbin/ftpd ftpd -l telnet stream tcp nowait root /usr/lbin/telnetd telnetd # Before uncommenting the "tftp" entry below, please make sure # that you have a "tftp" user in /etc/passwd. If you don't # have one, please consult the tftpd(1M) manual entry for # information about setting up this service. tftp dgram udp wait root /usr/lbin/tftpd tftpd\ /opt/ignite\ /var/opt/ignite #bootps dgram udp wait root /usr/lbin/bootpd bootpd #finger stream tcp nowait bin /usr/lbin/fingerd fingerd login stream tcp nowait root /usr/lbin/rlogind rlogind shell stream tcp nowait root /usr/lbin/remshd remshd exec stream tcp nowait root /usr/lbin/rexecd rexecd #uucp stream tcp nowait root /usr/sbin/uucpd uucpd ntalk dgram udp wait root /usr/lbin/ntalkd ntalkd ident stream tcp wait bin /usr/lbin/identd identd ## # # Other HP-UX network services # ## printer stream tcp nowait root /usr/sbin/rlpdaemon rlpdaemon -i ## # # inetd internal services # ## daytime stream tcp nowait root internal daytime dgram udp nowait root internal time stream tcp nowait root internal #time dgram udp nowait root internal echo stream tcp nowait root internal echo dgram udp nowait root internal discard stream tcp nowait root internal discard dgram udp nowait root internal chargen stream tcp nowait root internal chargen dgram udp nowait root internal ## # # rpc services, registered by inetd with portmap # Do not uncomment these unless your system is running portmap! # ## # WARNING: The rpc.mountd should now be started from a startup script. # Please enable the mountd startup script to start rpc.mountd. ## #rpc stream tcp nowait root /usr/sbin/rpc.rexd 100017 1 rpc.rexd #rpc dgram udp wait root /usr/lib/netsvc/rstat/rpc.rstatd 100001 2-4 rpc.rstatd #rpc dgram udp wait root /usr/lib/netsvc/rusers/rpc.rusersd 100002 1-2 rpc.rusersd #rpc dgram udp wait root /usr/lib/netsvc/rwall/rpc.rwalld 100008 1 rpc.rwalld #rpc dgram udp wait root /usr/sbin/rpc.rquotad 100011 1 rpc.rquotad #rpc dgram udp wait root /usr/lib/netsvc/spray/rpc.sprayd 100012 1 rpc.sprayd ## # # The standard remshd and rlogind do not include the Kerberized # code. You must install the InternetSvcSec/INETSVCS-SEC fileset and # configure Kerberos as described in the SIS(5) man page. # ## kshell stream tcp nowait root /usr/lbin/remshd remshd -K klogin stream tcp nowait root /usr/lbin/rlogind rlogind -K ## # # NCPM programs. # Do not uncomment these unless you are using NCPM. # ## #ncpm-pm dgram udp wait root /opt/ncpm/bin/ncpmd ncpmd #ncpm-hip dgram udp wait root /opt/ncpm/bin/hipd hipd dtspc stream tcp nowait root /usr/dt/bin/dtspcd /usr/dt/bin/dtspcd rpc xti tcp swait root /usr/dt/bin/rpc.ttdbserver 100083 1 /usr/dt/bin/rpc.ttdbs erver rpc dgram udp wait root /usr/dt/bin/rpc.cmsd 100068 2-5 rpc.cmsd recserv stream tcp nowait root /usr/lbin/recserv recserv -display :0 registrar stream tcp nowait root /etc/opt/resmon/lbin/registrar /etc/opt/resmon/ lbin/registrar instl_boots dgram udp wait root /opt/ignite/lbin/instl_bootd instl_bootd hacl-probe stream tcp nowait root /opt/cmom/lbin/cmomd /opt/cmom/lbin/cmo md -f /var/opt/cmom/cmomd.log hacl-cfg dgram udp wait root /usr/lbin/cmclconfd cmclconfd -p hacl-cfg stream tcp nowait root /usr/lbin/cmclconfd cmclconfd -c # more /var/adm/inetd.sec # @(#)inetd.sec $Revision: 1.10.214.1 $ $Date: 96/10/08 13:20:06 $ # # # The lines in the file contain a service name, permission field and # the Internet addresses or names of the hosts and/or networks # allowed to use that service in the local machine. # The form for each entry in this file is: # # # # For example: # # login allow 10.3-5 192.34.56.5 ahost anetwork # # The above entry allows the following hosts to attempt to access your system # using rlogin: # hosts in subnets 3 through 5 in network 10, # the host with Internet Address of 192.34.56.5, # the host by the name of "ahost", # all the hosts in the network "anetwork" # # mountd deny 192.23.4.3 # # The mountd entry denies host 192.23.4.3 access to the NFS rpc.mountd # server. # # Hosts and network names must be official names, not aliases. # See the inetd.sec(4) manual page for more information. dtspc allow 127.0.0.1 loopback b2000 -->查看hosts文件,发现原来该主机对应的135.129.24.4 b2000不见了 # more /etc/hosts # @(#)hosts $Revision: 1.9.214.1 $ $Date: 96/10/08 13:20:01 $ # # The form for each entry is: # # # For example: # 192.1.2.34 hpfcrm loghost # # See the hosts(4) manual page for more information. # Note: The entries cannot be preceded by a space. # The format described in this file is the correct format. # The original Berkeley manual page contains an error in # the format description. # 127.0.0.1 b2000 135.129.24.145 bird bird.home.com 135.129.24.2 ds10 135.129.24.3 ds20 127.0.0.1 localhost loopback -->发现netconf文件里面关于网络配置的都没了 # more /etc/rc.config.d/netconf INTERFACE_NAME[0]=lan0 HOSTNAME="b2000" # # OPERATING_SYSTEM: System name returned by uname -s (default "HP-UX") export OPERATING_SYSTEM=-t # more /etc/rc.config.d/netconf INTERFACE_NAME[0]=lan0 HOSTNAME="b2000" # # OPERATING_SYSTEM: System name returned by uname -s (default "HP-UX") export OPERATING_SYSTEM=-t # uname -s -t # uname -n b2000 # uname -a -t b2000 B.11.00 U 9000/785 2005197727 unlimited-user license # hostname b2000 -->查看目前机器的文件系统状态,正常的 # bdf Filesystem kbytes used avail %used Mounted on /dev/vg00/lvol3 524288 26863 466380 5% / /dev/vg00/lvol1 505392 51432 403416 11% /stand /dev/vg00/lvol8 1048576 775527 256549 75% /var /dev/vg00/lvol7 1048576 687882 338162 67% /usr /dev/vg00/lvol6 262144 1424 244490 1% /tmp /dev/vg00/lvol5 1048576 415666 593382 41% /opt /dev/vg00/lvol4 262144 11868 234694 5% /home /dev/vg01/lvol1 1048576 1365 981768 0% /cdrom # cd / # cd /stand # cd /var # cd /usr # cd /tmp # cd /opt # cd /home # cd /cdrom # cd -->查看syslog文件,也是正常的 # cd /var/adm/syslog # vi syslog.log :q! # more syslog.log Oct 19 11:11:55 b2000 syslogd: restart Oct 19 11:11:55 b2000 vmunix: gate64: sysvec_vaddr = 0xc0002000 for 1 pages Oct 19 11:11:55 b2000 vmunix: NOTICE: autofs_link(): File system was registered at index 3. Oct 19 11:11:55 b2000 vmunix: NOTICE: nfs3_link(): File system was registered at index 5. Oct 19 11:11:55 b2000 vmunix: 10 sba Oct 19 11:11:55 b2000 vmunix: 10/0 lba Oct 19 11:11:55 b2000 vmunix: 10/0/12/0 btlan3 Oct 19 11:11:55 b2000 vmunix: 10/0/13/0 audio Oct 19 11:11:55 b2000 vmunix: 10/0/14/0 side Oct 19 11:11:55 b2000 vmunix: 10/0/14/0.0 tgt Oct 19 11:11:55 b2000 vmunix: 10/0/14/0.0.0 sdisk Oct 19 11:11:55 b2000 vmunix: 10/0/14/0.7 tgt Oct 19 11:11:55 b2000 vmunix: 10/0/14/0.7.0 sctl Oct 19 11:11:55 b2000 vmunix: 10/0/14/1 superio Oct 19 11:11:55 b2000 vmunix: 10/0/14/1/1 asio0 Oct 19 11:11:55 b2000 vmunix: 10/0/14/1/2 asio0 Oct 19 11:11:55 b2000 vmunix: 10/0/14/1/3 SCentIf Oct 19 11:11:55 b2000 vmunix: 10/0/14/2 hcd Oct 19 11:11:55 b2000 vmunix: 10/0/14/2.1 hub Oct 19 11:11:55 b2000 vmunix: 10/0/15/0 c720 Oct 19 11:11:55 b2000 vmunix: 10/0/15/0.5 tgt Oct 19 11:11:55 b2000 vmunix: 10/0/15/0.5.0 sdisk Oct 19 11:11:55 b2000 vmunix: 10/0/15/0.6 tgt Oct 19 11:11:55 b2000 vmunix: 10/0/15/0.6.0 sdisk Oct 19 11:11:55 b2000 vmunix: 10/0/15/0.7 tgt Oct 19 11:11:55 b2000 vmunix: 10/0/15/0.7.0 sctl Oct 19 11:11:55 b2000 vmunix: 10/1 lba Oct 19 11:11:55 b2000 vmunix: Variable size pages used to map 1000 graf page s at fffffffffb000000 Oct 19 11:11:55 b2000 vmunix: 10/1/0/0 graph3 Oct 19 11:11:55 b2000 vmunix: 10/1/2/0 c720 Oct 19 11:11:55 b2000 vmunix: 10/1/2/0.1 tgt Oct 19 11:11:55 b2000 vmunix: 10/1/2/0.1.0 stape Oct 19 11:11:55 b2000 vmunix: 10/1/2/0.7 tgt Oct 19 11:11:55 b2000 vmunix: 10/1/2/0.7.0 sctl Oct 19 11:11:55 b2000 vmunix: 32 processor Oct 19 11:11:55 b2000 vmunix: 49 memory Oct 19 11:11:55 b2000 vmunix: btlan3: Initializing 10/100BASE-TX card at 10/0/12 /0.... Oct 19 11:11:55 b2000 vmunix: Oct 19 11:11:55 b2000 vmunix: System Console is on the Built-In Serial Inter face Oct 19 11:11:55 b2000 vmunix: Logical volume 64, 0x3 configured as ROOT Oct 19 11:11:55 b2000 vmunix: Logical volume 64, 0x2 configured as SWAP Oct 19 11:11:55 b2000 vmunix: Logical volume 64, 0x2 configured as DUMP Oct 19 11:11:55 b2000 vmunix: Swap device table: (start & size given in 512 -byte blocks) Oct 19 11:11:55 b2000 vmunix: entry 0 - major is 64, minor is 0x2; start = 0, size = 1048576 Oct 19 11:11:55 b2000 vmunix: Dump device table: (start & size given in 1-K byte blocks) Oct 19 11:11:55 b2000 vmunix: entry 0 - major is 31, minor is 0x25000; s tart = 527200, size = 524288 Oct 19 11:11:55 b2000 vmunix: Starting the STREAMS daemons-phase 1 Oct 19 11:11:55 b2000 vmunix: Create STCP device files Oct 19 11:11:55 b2000 vmunix: B2352B/9245XB HP-UX (B.11.00) #1: Wed Nov 5 2 2:38:19 PST 1997 Oct 19 11:11:55 b2000 vmunix: Oct 19 11:11:55 b2000 vmunix: Memory Information: Oct 19 11:11:55 b2000 vmunix: physical page size = 4096 bytes, logical page size = 4096 bytes Oct 19 11:11:55 b2000 vmunix: Physical: 1048576 Kbytes, lockable: 747968 Kby tes, available: 869184 Kbytes Oct 19 11:11:56 b2000 nettl[794]: nettl starting up. Oct 19 11:12:04 b2000 rpcbind: check_netconfig: Found CLTS loopback transport Oct 19 11:12:04 b2000 rpcbind: check_netconfig: Found COTS loopback transport Oct 19 11:11:55 b2000 vmunix: Oct 19 11:12:04 b2000 rpcbind: check_netconfig: Found COTS ORD loopback transpor t Oct 19 11:12:04 b2000 rpcbind: init_transport: check binding for udp Oct 19 11:12:04 b2000 rpcbind: init_transport: check binding for tcp Oct 19 11:12:04 b2000 rpcbind: init_transport: check binding for ticlts Oct 19 11:12:04 b2000 rpcbind: svc_tli_create: t_getname failed; T_IDLE Oct 19 11:12:04 b2000 rpcbind: svc_dg_create: could not get transport informatio n Oct 19 11:12:04 b2000 rpcbind: init_transport: Could not create rmtcall fd for t iclts Oct 19 11:12:04 b2000 rpcbind: init_transport: check binding for ticotsord Oct 19 11:12:04 b2000 rpcbind: init_transport: check binding for ticots Oct 19 11:12:05 b2000 inetd[906]: Reading configuration Oct 19 11:12:05 b2000 inetd[906]: protocol = tcp Oct 19 11:12:05 b2000 inetd[906]: ftp/tcp: Added service, server /usr/lbin/ftpd Oct 19 11:12:05 b2000 inetd[906]: telnet/tcp: Added service, server /usr/lbin/te lnetd Oct 19 11:12:05 b2000 inetd[906]: protocol = udp Oct 19 11:12:05 b2000 inetd[906]: tftp/udp: Added service, server /usr/lbin/tftp d Oct 19 11:12:05 b2000 inetd[906]: login/tcp: Added service, server /usr/lbin/rlo gind Oct 19 11:12:05 b2000 inetd[906]: shell/tcp: Added service, server /usr/lbin/rem shd Oct 19 11:12:05 b2000 inetd[906]: exec/tcp: Added service, server /usr/lbin/rexe cd Oct 19 11:12:05 b2000 inetd[906]: protocol = tcp Oct 19 11:12:05 b2000 above message repeats 4 times Oct 19 11:12:05 b2000 inetd[906]: ntalk/udp: Added service, server /usr/lbin/nta lkd Oct 19 11:12:05 b2000 inetd[906]: protocol = tcp Oct 19 11:12:05 b2000 inetd[906]: ident/tcp: Added service, server /usr/lbin/ide ntd Oct 19 11:12:05 b2000 inetd[906]: protocol = udp Oct 19 11:12:05 b2000 inetd[906]: printer/tcp: Added service, server /usr/sbin/r lpdaemon Oct 19 11:12:05 b2000 inetd[906]: daytime/tcp: Added service, server internal Oct 19 11:12:05 b2000 inetd[906]: protocol = udp Oct 19 11:12:05 b2000 inetd[906]: daytime/udp: Added service, server internal Oct 19 11:12:05 b2000 inetd[906]: time/tcp: Added service, server internal Oct 19 11:12:05 b2000 inetd[906]: echo/tcp: Added service, server internal Oct 19 11:12:05 b2000 inetd[906]: echo/udp: Added service, server internal Oct 19 11:12:06 b2000 inetd[906]: discard/tcp: Added service, server internal Oct 19 11:12:06 b2000 inetd[906]: discard/udp: Added service, server internal Oct 19 11:12:06 b2000 inetd[906]: chargen/tcp: Added service, server internal Oct 19 11:12:06 b2000 inetd[906]: chargen/udp: Added service, server internal Oct 19 11:12:06 b2000 inetd[906]: kshell/tcp: Added service, server /usr/lbin/re mshd Oct 19 11:12:06 b2000 inetd[906]: klogin/tcp: Added service, server /usr/lbin/rl ogind Oct 19 11:12:06 b2000 inetd[906]: protocol = udp Oct 19 11:12:06 b2000 above message repeats 3 times Oct 19 11:12:06 b2000 inetd[906]: dtspc/tcp: Added service, server /usr/dt/bin/d tspcd Oct 19 11:12:06 b2000 inetd[906]: protocol = udp Oct 19 11:12:06 b2000 inetd[906]: recserv/tcp: Added service, server /usr/lbin/r ecserv Oct 19 11:12:06 b2000 inetd[906]: registrar/tcp: Added service, server /etc/opt/ resmon/lbin/registrar Oct 19 11:12:06 b2000 inetd[906]: instl_boots/udp: Added service, server /opt/ig nite/lbin/instl_bootd Oct 19 11:12:06 b2000 inetd[906]: hacl-probe/tcp: Added service, server /opt/cmo m/lbin/cmomd Oct 19 11:12:06 b2000 inetd[906]: hacl-cfg/udp: Added service, server /usr/lbin/ cmclconfd Oct 19 11:12:06 b2000 inetd[906]: hacl-cfg/tcp: Added service, server /usr/lbin/ cmclconfd Oct 19 11:12:06 b2000 inetd[906]: protocol = udp Oct 19 11:12:06 b2000 above message repeats 2 times Oct 19 11:12:06 b2000 inetd[906]: rpc.cmsd/udp: Added service, server /usr/dt/bi n/rpc.cmsd Oct 19 11:12:06 b2000 inetd[906]: rpc.ttdbserver/tcp: Added service, server /usr /dt/bin/rpc.ttdbserver Oct 19 11:12:06 b2000 inetd[906]: protocol = tcp Oct 19 11:12:06 b2000 above message repeats 14 times Oct 19 11:12:06 b2000 inetd[906]: Configuration complete Oct 19 11:12:30 b2000 pwgrd: Started at Wed Oct 19 11:12:30 2005, pid = 1355 Oct 19 11:12:35 b2000 diagmond[1404]: started --->查看rc.log日志,正常 # more /etc/rc.log Old /etc/rc.log moved to /etc/rc.log.old ************************************************** HP-UX Start-up in progress Wed Oct 19 11:59:13 2005 ************************************************** Configure system crash dumps Output from "/sbin/rc1.d/S080crashconf start": ---------------------------- EXIT CODE: 0 Mount file systems Output from "/sbin/rc1.d/S100localmount start": ---------------------------- checking quotas Update kernel and loadable modules Output from "/sbin/rc1.d/S110kmbuild start": ---------------------------- "/sbin/rc1.d/S110kmbuild start" SKIPPED Initialize loadable modules Output from "/sbin/rc1.d/S112kminit start": ---------------------------- * All configured modules are registered successfully. NOTE: Module status Name ID Status Type ===================================================== krm 1 UNLOADED WSIO Setting hostname Output from "/sbin/rc1.d/S320hostname start": ---------------------------- Set privilege group Output from "/sbin/rc1.d/S400set_prvgrp start": ---------------------------- "/sbin/rc1.d/S400set_prvgrp start" SKIPPED Display date Output from "/sbin/rc1.d/S420set_date start": ---------------------------- "/sbin/rc1.d/S420set_date start" SKIPPED Copy processor logs to /var/tombstones Output from "/sbin/rc1.d/S430pdcinfo start": ---------------------------- Save system crash dump if needed Output from "/sbin/rc1.d/S440savecrash start": ---------------------------- /sbin/rc1.d/S440savecrash[47]: x: The specified number is not valid for this com mand. savecrash directory not set; defaulting to: /var/adm/crash savecrash: Dump previously saved, use -r to resave EXIT CODE: 2 - savecrash found no core dump to save "/sbin/rc1.d/S440savecrash start" SKIPPED Enable auxiliary swap space Output from "/sbin/rc1.d/S500swap_start start": ---------------------------- swap device(s) active Start syncer daemon Output from "/sbin/rc1.d/S520syncer start": ---------------------------- syncer started Configure HP Fibre Channel interfaces Output from "/sbin/rc2.d/S006hpfc start": ---------------------------- Configure Loopback interfaces (lo0) Output from "/sbin/rc2.d/S008net.init start": ---------------------------- Message catalog can't be opened/accessed for language zh_CN.hp15CN. Language C will used. Initialize Software Distributor agent daemon Output from "/sbin/rc2.d/S100swagentd start": ---------------------------- "/sbin/rc2.d/S100swagentd start" SKIPPED Configuring all unconfigured software filesets Output from "/sbin/rc2.d/S120swconfig start": ---------------------------- * Turning off all network based resolving services in '/etc/nsswitch.conf' * Removing the temporary '/etc/nsswitch.conf'. Recover editor crash files Output from "/sbin/rc2.d/S200clean_ex start": ---------------------------- preserving editor files (if any) Clean UUCP Output from "/sbin/rc2.d/S202clean_uucp start": ---------------------------- cleaning up uucp List and/or clear temporary files Output from "/sbin/rc2.d/S204clean_tmps start": ---------------------------- NOTE: Files in /tmp: total 388 -rw-r--r-- 1 root root 25 Sep 28 18:22 74.sh -rw-r--r-- 1 root root 25 Sep 28 20:23 77.sh -rw-r--r-- 1 root root 25 Oct 10 15:40 82.sh -rw-r--r-- 1 root root 25 Oct 12 16:16 83.sh -rw-r--r-- 1 root root 25 Oct 15 22:51 85.sh -rw-r--r-- 1 root root 23 Oct 19 11:59 87.sh -rw-r--r-- 1 root root 25 Oct 2 12:48 92.sh -rw-r--r-- 1 root root 25 Oct 16 12:16 99.sh -rw-r----- 1 root sys 151104 Oct 1 18:09 PHCO_28601.txt -rw-rw-rw- 1 root sys 44 Oct 18 23:27 batchftp.err -rw-rw-rw- 1 root sys 2270 Oct 18 23:51 batchftp.log -rw-r--r-- 1 root sys 0 Oct 18 18:53 dps.debug -rw-rw-rw- 1 root sys 17624 Oct 9 17:08 infolog.txt -r--r--r-- 1 root sys 1184 Sep 28 16:50 install.vars -r--r--r-- 1 root root 0 Oct 19 11:12 llbdbase.dat drwxr-xr-x 2 root root 96 Sep 28 16:49 lost+found -rw-r--r-- 1 root sys 5295 Oct 10 12:54 mwaps2640 -rw-r--r-- 1 root sys 2446 Oct 9 18:50 mwaps6470 -rw-r--r-- 1 root sys 0 Sep 28 18:24 null -rw-r--r-- 1 lp root 480 Oct 19 11:52 pdenq.log -rw------- 1 root root 264 Oct 19 11:56 portmap.file -rw------- 1 root root 1068 Oct 19 11:56 rpcbind.file -rw-r--r-- 1 root sys 56 Sep 28 18:00 sd_ipd_acl.1971 -rwxrwxrwx 1 root root 0 Sep 28 18:12 snmpd.log -rw-r--r-- 1 root sys 0 Sep 28 17:07 swlist NOTE: Files in /var/tmp: total 5544 -rw------- 1 root sys 0 Oct 18 11:51 OBAMHBAa01983 -rw------- 1 root sys 0 Oct 18 12:12 OBAMHBAa02392 -rw------- 1 root sys 0 Oct 18 12:18 OBAMHBAa03714 -rw------- 1 root sys 0 Oct 18 12:53 OBAMIBAa02775 -rw------- 1 root sys 0 Oct 18 11:57 OBAMPAAa02142 -rw------- 1 root sys 0 Oct 18 13:18 OBAMPAAa02887 -rw-r--r-- 1 root sys 109 Sep 29 00:11 aaaa02385 -rw-r--r-- 1 root sys 109 Sep 29 00:12 aaaa02459 -rw-rw-rw- 1 root sys 2766696 Oct 18 15:02 arch.include.1 -rw-r--r-- 1 root sys 1076 Sep 28 18:40 ems_inittab.old -rw-rw-rw- 1 root sys 2681 Oct 18 14:53 exclude.temp drwxrwxrwx 2 root sys 96 Oct 18 14:52 ign_configure -rw-r--r-- 1 root sys 4231 Sep 28 18:39 inetd.conf.old dr-xr-xr-x 2 bin bin 96 Sep 28 17:59 ntp -rw------- 1 root root 310 Oct 19 11:00 sh132.1 -rw------- 1 root root 343 Oct 19 11:00 sh132.2 -rw------- 1 root root 166 Oct 19 11:00 sh132.3 -rw------- 1 root sys 456 Sep 28 19:07 sh911.1 drwxr-xr-x 4 root root 96 Oct 18 12:35 stm1219 drwxr-xr-x 4 root sys 96 Oct 1 18:38 stm2340 -rw-r--r-- 1 root sys 6737 Oct 18 14:33 swagent.log -rw-r--r-- 1 root root 45118 Sep 28 19:08 swconfig.config.283 -rw-rw-rw- 1 root sys 207 Oct 18 14:53 tmp_cfg_file -rw-rw-rw- 1 root sys 128 Oct 18 14:53 vol.tmp "/sbin/rc2.d/S204clean_tmps start" SKIPPED Clean up old log files Output from "/sbin/rc2.d/S206clean_adm start": ---------------------------- Start system message logging daemon Output from "/sbin/rc2.d/S220syslogd start": ---------------------------- System message logger started Start pty allocator daemon Output from "/sbin/rc2.d/S230ptydaemon start": ---------------------------- Starting the ptydaemon Start network tracing and logging daemon Output from "/sbin/rc2.d/S300nettl start": ---------------------------- Initializing Network Tracing and Logging... Done. Configure HP Ethernet interfaces Output from "/sbin/rc2.d/S320hpether start": ---------------------------- Configure HP 100BT interfaces Output from "/sbin/rc2.d/S323hpbase100 start": ---------------------------- Configure HP SPP 100BT interfaces Output from "/sbin/rc2.d/S333hpsppci100 start": ---------------------------- No 100BT device configured in system (btlan6) "/sbin/rc2.d/S333hpsppci100 start" SKIPPED Configure LAN interfaces Output from "/sbin/rc2.d/S340net start": ---------------------------- Start name server daemon Output from "/sbin/rc2.d/S370named start": ---------------------------- "/sbin/rc2.d/S370named start" SKIPPED Start NFS core subsystem Output from "/sbin/rc2.d/S400nfs.core start": ---------------------------- starting NFS CORE networking starting up the rpcbind /usr/sbin/rpcbind starting up the nfskd daemon /usr/sbin/nfskd Start NIS+ server subsystem Output from "/sbin/rc2.d/S406nisplus.server start": ---------------------------- NOTE: NISPLUS_SERVER is not set, exiting. Start NIS+ client subsystem Output from "/sbin/rc2.d/S408nisplus.client start": ---------------------------- NOTE: NISPLUS_CLIENT is not set, exiting. Start NIS server subsystem Output from "/sbin/rc2.d/S410nis.server start": ---------------------------- NOTE: NIS_MASTER_SERVER or NIS_SLAVE_SERVER is not set, exiting. Start NIS client subsystem Output from "/sbin/rc2.d/S420nis.client start": ---------------------------- NOTE: NIS_CLIENT is not set, exiting. Start NFS client subsystem Output from "/sbin/rc2.d/S430nfs.client start": ---------------------------- NFS_CLIENT not set to one in /etc/rc.config.d/nfsconf, exiting. Start the Trusted Mode with Nis+ subsystem Output from "/sbin/rc2.d/S440comsec start": ---------------------------- starting the Trusted Table Sync Daemon (ttsyncd) Not an NIS+ root or master server "/sbin/rc2.d/S440comsec start" SKIPPED Configure pseudo devices for MAC/LLA access Output from "/sbin/rc2.d/S462maclan start": ---------------------------- Start multicast routing daemon Output from "/sbin/rc2.d/S490mrouted start": ---------------------------- "/sbin/rc2.d/S490mrouted start" SKIPPED Start Internet services daemon Output from "/sbin/rc2.d/S500inetd start": ---------------------------- Internet Services started Start dynamic routing daemon Output from "/sbin/rc2.d/S510gated start": ---------------------------- "/sbin/rc2.d/S510gated start" SKIPPED Start router discover protocol daemon Output from "/sbin/rc2.d/S520rdpd start": ---------------------------- "/sbin/rc2.d/S520rdpd start" SKIPPED Configuring PPP Interface Output from "/sbin/rc2.d/S522ppp start": ---------------------------- Creating 16 tunnel device nodes at major 138... Start RARP protocol daemon Output from "/sbin/rc2.d/S525rarpd start": ---------------------------- "/sbin/rc2.d/S525rarpd start" SKIPPED Start remote system status daemon Output from "/sbin/rc2.d/S530rwhod start": ---------------------------- "/sbin/rc2.d/S530rwhod start" SKIPPED Configuring man pages for Internet Services Output from "/sbin/rc2.d/S535inetsvcs start": ---------------------------- Starting mail daemon Output from "/sbin/rc2.d/S540sendmail start": ---------------------------- WARNING: local host name (b2000) is not qualified; fix $j in config file /etc/mail/aliases: 6 aliases, longest 9 bytes, 76 bytes total sendmail Starting outbound connection daemons for DDFA software Output from "/sbin/rc2.d/S550ddfa start": ---------------------------- "/sbin/rc2.d/S550ddfa start" SKIPPED Start SNMP Master Network Management daemon Output from "/sbin/rc2.d/S560SnmpMaster start": ---------------------------- Start OSPF MIB Network Management subAgent Output from "/sbin/rc2.d/S565OspfMib start": ---------------------------- "/sbin/rc2.d/S565OspfMib start" SKIPPED Start SNMP HP-UNIX Network Management subAgent Output from "/sbin/rc2.d/S565SnmpHpunix start": ---------------------------- Start SNMP MIB-2 Network Management subAgent Output from "/sbin/rc2.d/S565SnmpMib2 start": ---------------------------- Start SNMP Trap Dest Network Management subAgent Output from "/sbin/rc2.d/S565SnmpTrpDst start": ---------------------------- Start HA cluster SNMP subagent Output from "/sbin/rc2.d/S566cmsnmpagt start": ---------------------------- Start DCE daemons Output from "/sbin/rc2.d/S570dce start": ---------------------------- Beginning DCE startup... NOTE: No components of DCE are configured. Finished DCE startup. "/sbin/rc2.d/S570dce start" SKIPPED Start RPC daemon if needed Output from "/sbin/rc2.d/S590Rpcd start": ---------------------------- starting the DCE RPC Daemon /opt/dce/sbin/rpcd EXIT CODE: 1 "/sbin/rc2.d/S590Rpcd start" FAILED Start the Isogon License Server daemon Output from "/sbin/rc2.d/S600iforls start": ---------------------------- "/sbin/rc2.d/S600iforls start" SKIPPED Starting ISEE hpservices mad daemon. Output from "/sbin/rc2.d/S605hpservices start": ---------------------------- starting the Motive hpservices Daemon sleeping (5 sec) Start Runner Output from "/sbin/rc2.d/S606runner start": ---------------------------- Starting Runner Start remote boot daemon Output from "/sbin/rc2.d/S610rbootd start": ---------------------------- Remote boot daemon started Starting X Font Server at TCP port 7000 Output from "/sbin/rc2.d/S620xfs start": ---------------------------- "/sbin/rc2.d/S620xfs start" SKIPPED Start vt daemon Output from "/sbin/rc2.d/S630vt start": ---------------------------- starting the vtdaemon Start time synchronization Output from "/sbin/rc2.d/S660xntpd start": ---------------------------- "/sbin/rc2.d/S660xntpd start" SKIPPED Start accounting Output from "/sbin/rc2.d/S700acct start": ---------------------------- "/sbin/rc2.d/S700acct start" SKIPPED Install/Load XF86 DLKM Helper Modules Output from "/sbin/rc2.d/S700xf86 start": ---------------------------- Starting the password/group assist subsystem Output from "/sbin/rc2.d/S705pwgr start": ---------------------------- pwgrd started Starting HP Disk Array Manager daemons. Output from "/sbin/rc2.d/S710hparamgr start": ---------------------------- Starting disk array monitor daemons. Output from "/sbin/rc2.d/S710hparray start": ---------------------------- Start print spooler Output from "/sbin/rc2.d/S720lp start": ---------------------------- "/sbin/rc2.d/S720lp start" SKIPPED Starting HP Distributed Print Service Output from "/sbin/rc2.d/S722pd start": ---------------------------- pdclientd returned exit code: 255. Could not start pdclientd. See files /var/opt/pd/pdclientd/*.log for more information. Start clock daemon Output from "/sbin/rc2.d/S730cron start": ---------------------------- cron started Support Tools Informational Fileset Output from "/sbin/rc2.d/S740supprtinfo start": ---------------------------- Start diagnostic subsystem Output from "/sbin/rc2.d/S742diagnostic start": ---------------------------- Start auditing subsystem Output from "/sbin/rc2.d/S760auditing start": ---------------------------- "/sbin/rc2.d/S760auditing start" SKIPPED Start audio server daemon Output from "/sbin/rc2.d/S770audio start": ---------------------------- Start Distributed Single Logical Screen daemon Output from "/sbin/rc2.d/S780slsd start": ---------------------------- SAM System administration configuration Output from "/sbin/rc2.d/S800spa start": ---------------------------- MeasureWare performance software is being started. Output from "/sbin/rc2.d/S810mwa start": ---------------------------- The Transaction Tracker daemon is being started. The Transaction Tracker daemon /opt/perf/bin/ttd has been started. The MeasureWare scope collector is being started. Starting Scope in background. The MeasureWare server daemons are being started. ERROR: The DCE Host daemon (rpcd or dced) is not running. The MeasureWare daemon processes cannot be started until the Host daemon process is active. If you have configured a dce cell using SAM, the DCED flag will be set to 1 in the file /etc/rc.config.d/dce and the dced daemon will be launched at system bootup. If you have not configured a DCE cell, then you will need to ensure that rpcd is started at system bootup by setting START_LLBD to 1 in the file /etc/rc.config.d/ncs (for hp-ux releases prior to 11.00), or setting START_RPCD to 1 in the file /etc/rc.config.d/Rpcd (11.00 and later). Initialize Software Distributor agent daemon Output from "/sbin/rc2.d/S870swagentd start": ---------------------------- Copy processor logs to /var/tombstones Output from "/sbin/rc2.d/S900cpumap2 start": ---------------------------- '/sbin/init.d/cpumap2 background' started in the background, pid=1165 Starting Event Monitoring Service Output from "/sbin/rc2.d/S900ems start": ---------------------------- Starting the EMS Persistence Client Start EMS SNMP subagent Output from "/sbin/rc2.d/S900emsa start": ---------------------------- Configure HP Fibre Channel Mass Storage interfaces Output from "/sbin/rc2.d/S900hpfcms start": ---------------------------- Starting the RST EMS listener Output from "/sbin/rc2.d/S910rstEMSlistener start": ---------------------------- Start NFS server subsystem Output from "/sbin/rc3.d/S100nfs.server start": ---------------------------- NFS_SERVER not set to one in /etc/rc.config.d/nfsconf, exiting. Start X print server(s) Output from "/sbin/rc3.d/S200tps.rc start": ---------------------------- "/sbin/rc3.d/S200tps.rc start" SKIPPED Start Highly Available cluster Output from "/sbin/rc3.d/S800cmcluster start": ---------------------------- AUTOSTART_CMCLD not set to 1 in /etc/rc.config.d/cmcluster, exiting "/sbin/rc3.d/S800cmcluster start" SKIPPED ....unable to determine local system's hostname Output from "/sbin/rc3.d/S89desta start": ---------------------------- The WCCProxy is already running. Can't start another. /opt/hp/svctools/common/jre/bin/java[16]: getconf: cannot execute /opt/hp/svctools/common/jre/bin/java[16]: getconf: cannot execute Starting DESTA Director process. Logging outputs to: /opt/hp/svctools/specific/webes/logs/desta_dir.log Director in startup phase 2. The Director process has started successfully. Start CDE login server Output from "/sbin/rc3.d/S990dtlogin.rc start": ---------------------------- "/sbin/rc3.d/S990dtlogin.rc start" SKIPPED ************************************************** HP-UX run-level transition completed Wed Oct 19 12:01:19 2005 ************************************************** --->重启系统 ------------------------------------------------------------------------------ (c) Copyright 1995-2000, Hewlett-Packard Company, All rights reserved ------------------------------------------------------------------------------ Processor Speed State Coprocessor State I/D Cache --------- -------- --------------------- ----------------- ------------- 0 400 MHz Active Functional 512 kB/1 MB Central Bus Speed: 120 MHz Available memory: 1073741824 bytes Good memory required: 42999808 bytes Primary boot path: SCSI.5.0 Alternate boot path: SCSI.5.0 Console path: SERIAL_1.9600.8.none Keyboard path: USB Processor is booting from first available device. To discontinue, press any key within 10 seconds. 10 seconds expired. Proceeding... Searching for device(s) with bootable media... This may take several minutes. To discontinue search, press any key (termination may not be immediate). Attempting to boot Primary Path... BOOTABLE DEVICE FOUND: Path Number Device Path Device Type and Utilities ----------- ----------------- ------------------------- P0 SCSI.5.0 QUANTUM Atlas4-9LVD IPL Booting... Boot IO Dependent Code (IODC) revision 0 HARD Booted. ISL Revision A.00.38 OCT 26, 1994 ISL booting hpux Boot : disk(10/0/15/0.5.0.0.0.0.0;0)/stand/vmunix 7073792 + 871000 + 753040 start 0x21ba68 gate64: sysvec_vaddr = 0xc0002000 for 1 pages NOTICE: autofs_link(): File system was registered at index 3. NOTICE: nfs3_link(): File system was registered at index 5. System Console is on the Built-In Serial Interface Logical volume 64, 0x3 configured as ROOT Logical volume 64, 0x2 configured as SWAP Logical volume 64, 0x2 configured as DUMP Swap device table: (start & size given in 512-byte blocks) entry 0 - major is 64, minor is 0x2; start = 0, size = 1048576 Starting the STREAMS daemons-phase 1 Checking root file system. file system is clean - log replay is not required Root check done. Create STCP device files B2352B/9245XB HP-UX (B.11.00) #1: Wed Nov 5 22:38:19 PST 1997 Memory Information: physical page size = 4096 bytes, logical page size = 4096 bytes Physical: 1048576 Kbytes, lockable: 747968 Kbytes, available: 869184 Kbytes /sbin/ioinitrc: /sbin/bcheckrc: Checking for LVM volume groups and Activating (if any exist) Volume group "/dev/vg00" has been successfully changed. Activated volume group Volume group "/dev/vg01" has been successfully changed. Resynchronized volume group /dev/vg00 Resynchronized volume group /dev/vg01 vxfs fsck: sanity check: root file system OK (mounted read/write) Checking hfs file systems /sbin/fsclean: /dev/vg00/lvol1 (mounted) ok HFS file systems are OK, not running fsck Checking vxfs file systems /dev/vg00/lvol8 : vxfs fsck: sanity check: /dev/vg00/lvol8 OK /dev/vg01/lvol1 : vxfs fsck: sanity check: /dev/vg01/lvol1 OK /dev/vg00/lvol3 : vxfs fsck: sanity check: root file system OK (mounted read/write) /dev/vg00/lvol4 : vxfs fsck: sanity check: /dev/vg00/lvol4 OK /dev/vg00/lvol5 : vxfs fsck: sanity check: /dev/vg00/lvol5 OK /dev/vg00/lvol6 : vxfs fsck: sanity check: /dev/vg00/lvol6 OK /dev/vg00/lvol7 : vxfs fsck: sanity check: /dev/vg00/lvol7 OK (c)Copyright 1983-1997 Hewlett-Packard Co., All Rights Reserved. (c)Copyright 1979, 1980, 1983, 1985-1993 The Regents of the Univ. of California (c)Copyright 1980, 1984, 1986 Novell, Inc. (c)Copyright 1986-1992 Sun Microsystems, Inc. (c)Copyright 1985, 1986, 1988 Massachusetts Institute of Technology (c)Copyright 1989-1993 The Open Software Foundation, Inc. (c)Copyright 1986 Digital Equipment Corp. (c)Copyright 1990 Motorola, Inc. (c)Copyright 1990, 1991, 1992 Cornell University (c)Copyright 1989-1991 The University of Maryland (c)Copyright 1988 Carnegie Mellon University (c)Copyright 1991-1997 Mentat, Inc. (c)Copyright 1996 Morning Star Technologies, Inc. (c)Copyright 1996 Progressive Systems, Inc. (c)Copyright 1997 Isogon Corporation RESTRICTED RIGHTS LEGEND Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in sub-paragraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause in DFARS 252.227-7013. Hewlett-Packard Company 3000 Hanover Street Palo Alto, CA 94304 U.S.A. Rights for non-DOD U.S. Government Departments and Agencies are as set forth in FAR 52.227-19(c)(1,2). /sbin/auto_parms: DHCP access is disabled (see /etc/auto_parms.log) HP-UX Start-up in progress __________________________ Configure system crash dumps .............................. OK Mount file systems ........................................ OK Update kernel and loadable modules ........................ N/A Initialize loadable modules ............................... OK Setting hostname .......................................... OK Set privilege group ....................................... N/A Display date .............................................. N/A Copy processor logs to /var/tombstones .................... OK Save system crash dump if needed .......................... N/A Enable auxiliary swap space ............................... OK Start syncer daemon ....................................... OK Configure HP Fibre Channel interfaces ..................... OK Configure Loopback interfaces (lo0) ....................... OK Initialize Software Distributor agent daemon .............. N/A Configuring all unconfigured software filesets ............ OK Recover editor crash files ................................ OK Clean UUCP ................................................ OK List and/or clear temporary files ......................... N/A Clean up old log files .................................... OK Start system message logging daemon ....................... OK Start pty allocator daemon ................................ OK Start network tracing and logging daemon .................. OK Configure HP Ethernet interfaces .......................... OK Configure HP 100BT interfaces ............................. OK Configure HP SPP 100BT interfaces ......................... N/A Configure LAN interfaces .................................. OK Start name server daemon .................................. N/A Start NFS core subsystem .................................. OK Start NIS+ server subsystem ............................... OK Start NIS+ client subsystem ............................... OK Start NIS server subsystem ................................ OK Start NIS client subsystem ................................ OK Start NFS client subsystem ................................ OK Start the Trusted Mode with Nis+ subsystem ................ N/A Configure pseudo devices for MAC/LLA access ............... OK Start multicast routing daemon ............................ N/A Start Internet services daemon ............................ OK Start dynamic routing daemon .............................. N/A Start router discover protocol daemon ..................... N/A Configuring PPP Interface ................................. OK Start RARP protocol daemon ................................ N/A Start remote system status daemon ......................... N/A Configuring man pages for Internet Services ............... OK Starting mail daemon ...................................... OK Starting outbound connection daemons for DDFA software .... N/A Start SNMP Master Network Management daemon ............... OK Start OSPF MIB Network Management subAgent ................ N/A Start SNMP HP-UNIX Network Management subAgent ............ OK Start SNMP MIB-2 Network Management subAgent .............. OK Start SNMP Trap Dest Network Management subAgent .......... OK Start HA cluster SNMP subagent ............................ OK Start DCE daemons ......................................... N/A Start RPC daemon if needed ................................ FAIL * Start the Isogon License Server daemon .................... N/A Starting ISEE hpservices mad daemon. ...................... OK Start Runner .............................................. OK Start remote boot daemon .................................. OK Starting X Font Server at TCP port 7000 ................... N/A Start vt daemon ........................................... OK Start time synchronization ................................ N/A Start accounting .......................................... N/A Install/Load XF86 DLKM Helper Modules ..................... OK Starting the password/group assist subsystem .............. OK Starting HP Disk Array Manager daemons. ................... OK Starting disk array monitor daemons. ...................... OK Start print spooler ....................................... N/A Starting HP Distributed Print Service ..................... OK Start clock daemon ........................................ OK Support Tools Informational Fileset ....................... OK Start diagnostic subsystem ................................ OK Start auditing subsystem .................................. N/A Start audio server daemon ................................. OK Start Distributed Single Logical Screen daemon ............ OK SAM System administration configuration ................... OK MeasureWare performance software is being started. ........ OK Initialize Software Distributor agent daemon .............. OK Copy processor logs to /var/tombstones .................... OK Starting Event Monitoring Service ......................... OK Start EMS SNMP subagent ................................... OK Configure HP Fibre Channel Mass Storage interfaces ........ OK Starting the RST EMS listener ............................. OK Start NFS server subsystem ................................ OK Start X print server(s) ................................... N/A Start Highly Available cluster ............................ N/A ....unable to determine local system's hostname ........... OK Start CDE login server .................................... N/A * - An error has occurred ! * - Refer to the file /etc/rc.log for more information.