# netconf:  configuration values for core networking subsystems
#
# @(#)B.11.11_LR $Revision: 1.6.119.6 $ $Date: 97/09/10 15:56:01 $
#
# HOSTNAME:           Name of your system for uname -S and hostname
#
# OPERATING_SYSTEM:   Name of operating system returned by uname -s
#                     ---- DO NOT CHANGE THIS VALUE ----
#
# LOOPBACK_ADDRESS:   Loopback address
#                     ---- DO NOT CHANGE THIS VALUE ----
#
# IMPORTANT:  for 9.x-to-10.0 transition, do not put blank lines between
# the next set of statements

HOSTNAME="oradb"
OPERATING_SYSTEM=HP-UX
LOOPBACK_ADDRESS=127.0.0.1

# Internet configuration parameters.  See ifconfig(1m), autopush(1m)
# 
# INTERFACE_NAME:     Network interface name (see lanscan(1m))
#
# IP_ADDRESS:         Hostname (in /etc/hosts) or IP address in decimal-dot
#                     notation (e.g., 192.1.2.3)
#
# SUBNET_MASK:        Subnetwork mask in decimal-dot notation, if different
#                     from default
#
# BROADCAST_ADDRESS:  Broadcast address in decimal-dot notation, if 
#                     different from default
#
# INTERFACE_STATE:    Desired interface state at boot time.
#                     either up or down, default is up.
#
# DHCP_ENABLE         Determines whether or not DHCP client functionality 
#                     will be enabled on the network interface (see 
#                     auto_parms(1M), dhcpclient(1M)). DHCP clients get 
#                     their IP address assignments from DHCP servers.
#                     1 enables DHCP client functionality; 0 disables it.
#
# For each additional network interfaces, add a set of variable assignments
# like the ones below, changing the index to "[1]", "[2]" et cetera.
#
# IMPORTANT:  for 9.x-to-10.0 transition, do not put blank lines between
# the next set of statements

# Internet routing configuration.  See route(1m), routing(7)
#
# ROUTE_DESTINATION:  Destination hostname (in /etc/hosts) or host or network
#                     IP address in decimal-dot notation, preceded by the word
#                     "host" or "net"; or simply the word "default".
#
# ROUTE_MASK:         Subnetwork mask in decimal-dot notation, or C language
#                     hexadecimal notation.  This is an optional field.
#                     A IP address, subnet mask pair uniquely identifies
#                     a subnet to be reached. If a subnet mask is not given,
#                     then the system will assign the longest subnet mask
#                     of the configured network interfaces to this route.
#                     If there is no matching subnet mask, then the system
#                     will assign the default network mask as the route's
#                     subnet mask. 
#
# ROUTE_GATEWAY:      Gateway hostname (in /etc/hosts) or IP address in
#                     decimal-dot notation.  If local interface, must use the
#                     same form as used for IP_ADDRESS above (hostname or 
#                     decimal-dot notation). If loopback interface, i.e., 
#		      127.0.0.1, the ROUTE_COUNT must be set to zero.
#
# ROUTE_COUNT:        An integer that indicates whether the gateway is a
#                     remote interface (one) or the local interface (zero)
#		      or loopback interface (e.g., 127.*).
#
# ROUTE_ARGS:         Route command arguments and options.  This variable
#                     may contain a combination of the following arguments:
#                     "-f", "-n" and "-p pmtu".
#
# For each additional route, add a set of variable assignments like the ones
# below, changing the index to "[1]", "[2]" et cetera.
#
# IMPORTANT:  for 9.x-to-10.0 transition, do not put blank lines between
# the next set of statements

#ROUTE_DESTINATION[0]=default
#ROUTE_MASK[0]=""
#ROUTE_GATEWAY[0]=172.16.100.1
#ROUTE_COUNT[0]=1
#ROUTE_ARGS[0]=""

# Dynamic routing daemon configuration.  See gated(1m)
#
# GATED:        Set to 1 to start gated daemon.
# GATED_ARGS:   Arguments to the gated daemon.

GATED=0
GATED_ARGS=""

#
# Router Discover Protocol daemon configuration.  See rdpd(1m)
#
# RDPD:         Set to 1 to start rdpd daemon
#       

RDPD=0

#
# Reverse ARP daemon configuration.  See rarpd(1m)
#
# RARP:         Set to 1 to start rarpd daemon
#       

RARP=0

INTERFACE_NAME[0]=lan0
IP_ADDRESS[0]=172.16.100.35
SUBNET_MASK[0]=255.255.255.0
ROUTE_GATEWAY[0]=172.16.100.1
BROADCAST_ADDRESS[0]=""
ROUTE_COUNT[0]=1
ROUTE_DESTINATION[0]=default
IP_ADDRESS[1]=10.17.4.15
SUBNET_MASK[1]=255.255.255.224
INTERFACE_NAME[1]=lan1
BROADCAST_ADDRESS[1]=10.17.4.31
INTERFACE_STATE[1]=up