Array Diagnostic Utility Inspection Report Version 7.72.1.0 Date/Time: Wednesday, April 11, 2007 1:30:46PM Computer Model: HP Server SLOT SUMMARY: Slot Num Slot Type Array Controllers and Host Adapters Detected -------- --------- -------------------------------------------- SLOT 0 PCI Smart Array 6i Controller SLOT 0 Smart Array 6i Controller ERROR REPORT: No problems detected SUBSYSTEM INFORMATION: Chassis Serial Num: GB8523BXA6 This Controller Array Serial Number: Not Available Cache Serial Number: Not Available Other Controller Array Serial Number: Not Available Cache Serial Number: Not Available CONTROLLER IDENTIFICATION: Configured Logical Drives: 1 Configuration Signature: 0xa01457b3 Controller Firmware Rev: 2.36 Controller ROM Revision: 2.36 Controller Hardware Rev: 0x01 Boot Block Version: 3.86 Board ID: 0x40910e11 Cable or Config Error: 0x00 (No) Invalid Host RAM Address: No CPU Revision: 0x50 CPU to PCI ASIC Rev: 0x00 Cache Controller ASIC Rev: 0x00 PCI to Host ASIC Rev: 0x00 Marketing Revision: 0x42 (Rev B) Expand Disable Code: 0x01 SCSI Chip Count: 2 Max SCSI IDs per Bus: 16 Big Drive Map: 0x0000 0x003f 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Big Ext Drive Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Big Non-Disk Drive Map: 0x0000 0x0080 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Fibre Chip Count: 0 LKS: 0x00 AMS: 0x00 FS: 0x00 0x00 0x00 0x00 0x00 0x00 0x2e32 0x3633 0x01 0x00 0x00 0x00 Recovery ROM Inactive Image Revision: 2.36 Recovery ROM Active Image Flags Status: 0x01 Percent Write Cache: 0 Daughterboard Size(MB): 0 Cache Battery Count: 0 Total Ctlr Memory Size: 64 More Controller Flags: 0x00 X-Board Host I2C Autorev: 0x00 LOGICAL DRIVE IDENTIFICATION: Logical Drive 1: Sector Size: 512 Sectors Available: 213367680 Fault Tolerance Mode: Mirroring Logical Param Table: cyl=26148 heads=255 sec/track=32 xlate sig=0x0 BIOS Disabled: No LOGICAL DRIVE CONFIGURATION: Logical Drive 1: Configuration Signature: 0xa01457b3 Mapping Scheme: Multiple Block Physical Drives: 6 (number not valid after drive movement) This Logical Drive: 6 (excluding spare drives) Fault Tolerance Mode: Mirroring Logical Param Table: cyl=26148 heads=255 sec/track=32 xlate sig=0x0 Distribution Factor: 256 Operating System: 64768 Controller Order: 0 Additional Information: 0 Offset to Data: 0 Int 13h Support Enabled: Yes Sectors on Volume: 213367680 Sectors per Drive: 71122688 Big Drive Assignment Map: 0x0000 0x003f 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Big Spare Assignment Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Array Accelerator is enabled for this logical drive. LOGICAL DRIVE STATUS: Logical Drive 1: Drive Status: OK Blocks to Rebuild: 0 Blocks Re-mapped: Spare Status Flags: 0x00 Spare to Replaced Map: See Big Spare to Replace Map: Media Was Exchanged: No Cache Failure: No Expand Failure: 0x00 Unit Flags: 0x00 Big Remap Count: All Counts Zero Big Drive Failure Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Big Replacement Drive Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Big Active Spare Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Big Spare to Replace Map: No spares have replaced any drives Big Spare Marked OK Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 MONITOR AND PERFORMANCE DATA: SCSI Port 1, Drive ID 0 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 1 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 2 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 3 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 4 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 5 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 6 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 7 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 8 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 9 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 10 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 11 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 12 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 13 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 14 Not Available DRIVE ERROR LOG: Not Available SCSI Port 1, Drive ID 15 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 0 Factory: Serial #, Firmware Rev, and Mfg/Model #: 41 4e 4c 31 50 35 35 30 36 32 4d 56 30 35 32 31 ANL1P55062MV0521 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 38 35 37 35 20 20 AQ BF03688575 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Since Power: Serial #, Firmware Rev, and Mfg/Model #: 41 4e 4c 31 50 35 35 30 36 32 4d 56 30 35 32 31 ANL1P55062MV0521 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 38 35 37 35 20 20 AQ BF03688575 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Threshold Flags: 0x0001 Serial Number Control: 0x8054 Firmware Revision Control: 0x8248 Mfg/Model Number Control: 0x8268 Factory Since Power Threshold Control Serv. Time 000e3406 000b1e95 ffffffff 8184 Read Blks 0000000f52f681c3 00000005329619c3 8108 Hrd Read 00000000 00000000 ffffffff 8184 Rtry Read 00000000 00000000 ffffffff 8184 ECC Read 0000000000000000 0000000000000000 ffffffffffffffff 8188 Write Blks 00000015b49c4b1e 000000129a6e25cc 8108 Hrd Write 00000000 00000000 ffffffff 8184 Rtry Write 00000000 00000000 ffffffff 8184 Seeks 0000000000000000 0000000000000000 8108 Seek Errs 0000000000000000 0000000000000000 ffffffffffffffff 8188 Spin Cyls 00000000 00000001 ffffffff 8184 Spin Time ffff ffff ffff 8a82 Test 1 ffff ffff ffff 0a82 Test 2 ffff ffff ffff 8a82 Test 3 ffff ffff ffff 8a82 Test 4 ffff ffff ffff 8a82 Spare Blks ffffffff ffffffff 0a04 Re-mapped ffffffff ffffffff ffffffff 8d84 DRQ Tmots ffff ffff ffff 0982 Timeouts 0000 0000 ffff 0182 Rebuilds 0000 0000 ffff 0182 Spn Retrs ffff ffff ffff 0982 Fl Rd Recv 0000 0000 ffff 8182 Fl Wt Recv 0000 0000 ffff 0182 Format Err 0000 0000 ffff 0182 POST Err ffff ffff ffff 0982 Drv Nt Ry 00000000 00000000 ffffffff 0184 Reallc Abt ffffffff ffffffff ffffffff 0984 IRQ Gltchs ffffffff ffffffff ffffffff 0984 Bus Flts 00000000 00000000 ffffffff 8184 Hot Plgs 00000000 00000000 ffffffff 0184 Tk Rwt Err ffff ffff ffff 0982 Rmp Wt Err ffff ffff ffff 0982 Bg Fw Rev 0000000000000000 0000000000000000 0a48 Med Flrs 0000 0000 ffff 0182 Hrdw Errs 0000 0000 ffff 0182 Abt Cmd Fl 0000 0000 ffff 0182 Spn Up Fl 0000 0000 ffff 0182 Bd Tgt Cnt 0000 0000 ffff 0182 Pred Fails 00000000 00000000 00000000 2184 DRIVE ERROR LOG: Error Log Header: Parameter Length = 0x14 Entry Size = 0x0014 Current Entry = 0x01 Total Errors Logged = 0x00000001 Error Log Data: SCSI CAM Sense Sense Stat Stat Key Code Qual Block(Vl) Time Op Info ---- ---- ----- ----- ---- --------- ---- -- ---- 00 0e 00 00 00 00c35240(0) 000315e1 2a 0000 SCSI Port 2, Drive ID 1 Factory: Serial #, Firmware Rev, and Mfg/Model #: 41 4e 4c 31 50 35 35 30 35 55 43 45 30 35 32 30 ANL1P5505UCE0520 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 38 35 37 35 20 20 AQ BF03688575 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Since Power: Serial #, Firmware Rev, and Mfg/Model #: 41 4e 4c 31 50 35 35 30 35 55 43 45 30 35 32 30 ANL1P5505UCE0520 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 38 35 37 35 20 20 AQ BF03688575 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Threshold Flags: 0x0001 Serial Number Control: 0x8054 Firmware Revision Control: 0x8248 Mfg/Model Number Control: 0x8268 Factory Since Power Threshold Control Serv. Time 000e3406 000b1e95 ffffffff 8184 Read Blks 0000000f2a2162d4 000000050c91fc5a 8108 Hrd Read 00000000 00000000 ffffffff 8184 Rtry Read 00000001 00000001 ffffffff 8184 ECC Read 0000000000000000 0000000000000000 ffffffffffffffff 8188 Write Blks 0000001630aff4c7 0000001300ff0992 8108 Hrd Write 00000000 00000000 ffffffff 8184 Rtry Write 00000000 00000000 ffffffff 8184 Seeks 0000000000000000 0000000000000000 8108 Seek Errs 0000000000000000 0000000000000000 ffffffffffffffff 8188 Spin Cyls 00000000 00000001 ffffffff 8184 Spin Time ffff ffff ffff 8a82 Test 1 ffff ffff ffff 0a82 Test 2 ffff ffff ffff 8a82 Test 3 ffff ffff ffff 8a82 Test 4 ffff ffff ffff 8a82 Spare Blks ffffffff ffffffff 0a04 Re-mapped ffffffff ffffffff ffffffff 8d84 DRQ Tmots ffff ffff ffff 0982 Timeouts 0000 0000 ffff 0182 Rebuilds 0000 0000 ffff 0182 Spn Retrs ffff ffff ffff 0982 Fl Rd Recv 0000 0000 ffff 8182 Fl Wt Recv 0000 0000 ffff 0182 Format Err 0000 0000 ffff 0182 POST Err ffff ffff ffff 0982 Drv Nt Ry 00000000 00000000 ffffffff 0184 Reallc Abt ffffffff ffffffff ffffffff 0984 IRQ Gltchs ffffffff ffffffff ffffffff 0984 Bus Flts 00000000 00000000 ffffffff 8184 Hot Plgs 00000000 00000000 ffffffff 0184 Tk Rwt Err ffff ffff ffff 0982 Rmp Wt Err ffff ffff ffff 0982 Bg Fw Rev 0000000000000000 0000000000000000 0a48 Med Flrs 0000 0000 ffff 0182 Hrdw Errs 0000 0000 ffff 0182 Abt Cmd Fl 0000 0000 ffff 0182 Spn Up Fl 0000 0000 ffff 0182 Bd Tgt Cnt 0000 0000 ffff 0182 Pred Fails 00000000 00000000 00000000 2184 DRIVE ERROR LOG: Error Log Header: Parameter Length = 0x14 Entry Size = 0x0014 Current Entry = 0x02 Total Errors Logged = 0x00000002 Error Log Data: SCSI CAM Sense Sense Stat Stat Key Code Qual Block(Vl) Time Op Info ---- ---- ----- ----- ---- --------- ---- -- ---- 00 0e 00 00 00 00c35140(0) 000315e1 2a 0000 02 04 01 17 08 00c34f40(1) 000c4de3 28 0000 SCSI Port 2, Drive ID 2 Factory: Serial #, Firmware Rev, and Mfg/Model #: 41 4e 4c 31 50 35 35 30 36 31 59 57 30 35 32 31 ANL1P55061YW0521 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 38 35 37 35 20 20 AQ BF03688575 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Since Power: Serial #, Firmware Rev, and Mfg/Model #: 41 4e 4c 31 50 35 35 30 36 31 59 57 30 35 32 31 ANL1P55061YW0521 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 38 35 37 35 20 20 AQ BF03688575 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Threshold Flags: 0x0001 Serial Number Control: 0x8054 Firmware Revision Control: 0x8248 Mfg/Model Number Control: 0x8268 Factory Since Power Threshold Control Serv. Time 000e3406 000b1e95 ffffffff 8184 Read Blks 0000000f4d6989f2 000000052cd74ee9 8108 Hrd Read 00000000 00000000 ffffffff 8184 Rtry Read 00000000 00000000 ffffffff 8184 ECC Read 0000000000000000 0000000000000000 ffffffffffffffff 8188 Write Blks 000000149230d81e 00000011a01cb95f 8108 Hrd Write 00000000 00000000 ffffffff 8184 Rtry Write 00000000 00000000 ffffffff 8184 Seeks 0000000000000000 0000000000000000 8108 Seek Errs 0000000000000000 0000000000000000 ffffffffffffffff 8188 Spin Cyls 00000000 00000001 ffffffff 8184 Spin Time ffff ffff ffff 8a82 Test 1 ffff ffff ffff 0a82 Test 2 ffff ffff ffff 8a82 Test 3 ffff ffff ffff 8a82 Test 4 ffff ffff ffff 8a82 Spare Blks ffffffff ffffffff 0a04 Re-mapped ffffffff ffffffff ffffffff 8d84 DRQ Tmots ffff ffff ffff 0982 Timeouts 0000 0000 ffff 0182 Rebuilds 0000 0000 ffff 0182 Spn Retrs ffff ffff ffff 0982 Fl Rd Recv 0000 0000 ffff 8182 Fl Wt Recv 0000 0000 ffff 0182 Format Err 0000 0000 ffff 0182 POST Err ffff ffff ffff 0982 Drv Nt Ry 00000000 00000000 ffffffff 0184 Reallc Abt ffffffff ffffffff ffffffff 0984 IRQ Gltchs ffffffff ffffffff ffffffff 0984 Bus Flts 00000000 00000000 ffffffff 8184 Hot Plgs 00000000 00000000 ffffffff 0184 Tk Rwt Err ffff ffff ffff 0982 Rmp Wt Err ffff ffff ffff 0982 Bg Fw Rev 0000000000000000 0000000000000000 0a48 Med Flrs 0000 0000 ffff 0182 Hrdw Errs 0000 0000 ffff 0182 Abt Cmd Fl 0000 0000 ffff 0182 Spn Up Fl 0000 0000 ffff 0182 Bd Tgt Cnt 0000 0000 ffff 0182 Pred Fails 00000000 00000000 00000000 2184 DRIVE ERROR LOG: Error Log Header: Parameter Length = 0x14 Entry Size = 0x0014 Current Entry = 0x01 Total Errors Logged = 0x00000001 Error Log Data: SCSI CAM Sense Sense Stat Stat Key Code Qual Block(Vl) Time Op Info ---- ---- ----- ----- ---- --------- ---- -- ---- 00 0e 00 00 00 00c35140(0) 000315e1 2a 0000 SCSI Port 2, Drive ID 3 Factory: Serial #, Firmware Rev, and Mfg/Model #: 41 4e 4c 31 50 35 36 30 36 52 4e 39 30 35 32 33 ANL1P5606RN90523 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 38 35 37 35 20 20 AQ BF03688575 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Since Power: Serial #, Firmware Rev, and Mfg/Model #: 41 4e 4c 31 50 35 36 30 36 52 4e 39 30 35 32 33 ANL1P5606RN90523 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 38 35 37 35 20 20 AQ BF03688575 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Threshold Flags: 0x0001 Serial Number Control: 0x8054 Firmware Revision Control: 0x8248 Mfg/Model Number Control: 0x8268 Factory Since Power Threshold Control Serv. Time 000b1e24 000b1e24 ffffffff 8184 Read Blks 00000000e9f78fc7 00000000e9f78f4b 8108 Hrd Read 00000989 00000989 ffffffff 8184 Rtry Read 0000020e 0000020e ffffffff 8184 ECC Read 0000000000000000 0000000000000000 ffffffffffffffff 8188 Write Blks 000000129d1b6f08 000000129d1b6f08 8108 Hrd Write 00000000 00000000 ffffffff 8184 Rtry Write 00000000 00000000 ffffffff 8184 Seeks 0000000000000000 0000000000000000 8108 Seek Errs 0000000000000000 0000000000000000 ffffffffffffffff 8188 Spin Cyls 00000001 00000001 ffffffff 8184 Spin Time ffff 0059 ffff 8a82 Test 1 ffff ffff ffff 0a82 Test 2 ffff ffff ffff 8a82 Test 3 ffff ffff ffff 8a82 Test 4 ffff ffff ffff 8a82 Spare Blks ffffffff ffffffff 0a04 Re-mapped fffffffe fffffffe ffffffff 8d84 DRQ Tmots ffff ffff ffff 0982 Timeouts 0000 0000 ffff 0182 Rebuilds 0001 0001 ffff 0182 Spn Retrs ffff ffff ffff 0982 Fl Rd Recv 0000 0000 ffff 8182 Fl Wt Recv 0000 0000 ffff 0182 Format Err 0000 0000 ffff 0182 POST Err ffff ffff ffff 0982 Drv Nt Ry 00000000 00000000 ffffffff 0184 Reallc Abt ffffffff ffffffff ffffffff 0984 IRQ Gltchs ffffffff ffffffff ffffffff 0984 Bus Flts 00000000 00000000 ffffffff 8184 Hot Plgs 00000000 00000000 ffffffff 0184 Tk Rwt Err ffff ffff ffff 0982 Rmp Wt Err ffff ffff ffff 0982 Bg Fw Rev 0000000000000000 0000000000000000 0a48 Med Flrs 0000 0000 ffff 0182 Hrdw Errs 0000 0000 ffff 0182 Abt Cmd Fl 0000 0000 ffff 0182 Spn Up Fl 0000 0000 ffff 0182 Bd Tgt Cnt 0000 0000 ffff 0182 Pred Fails 00000000 00000000 00000000 2184 DRIVE ERROR LOG: Error Log Header: Parameter Length = 0x14 Entry Size = 0x0014 Current Entry = 0x01 Total Errors Logged = 0x00000655 Error Log Data: SCSI CAM Sense Sense Stat Stat Key Code Qual Block(Vl) Time Op Info ---- ---- ----- ----- ---- --------- ---- -- ---- 02 04 03 11 01 00c350df(1) 000b0fe9 28 0000 02 04 03 11 01 00c350fd(1) 000a5f91 28 0000 02 04 01 17 08 00c34f64(1) 000a5f94 28 0000 02 04 03 11 01 00c35156(1) 000a6d66 28 0000 02 04 03 11 01 00c35155(1) 000a80df 28 0000 02 04 03 11 01 00c350db(1) 000a80e8 28 0000 02 04 03 11 01 00c350db(1) 000a80e9 28 0000 02 04 03 11 01 00c350dc(1) 000a9853 28 0000 02 04 03 11 01 00c350dd(1) 000a9ea7 28 0000 02 04 03 11 01 00c35156(1) 000aa2b2 28 0000 02 04 01 17 08 00c35155(1) 000aacc0 28 0000 02 04 03 11 01 00c3588b(1) 000ac9cb 28 0000 02 04 01 17 08 00c34f64(1) 000aca21 28 0000 02 04 01 17 08 00c35156(1) 000acfe0 28 0000 02 04 01 17 08 00c35155(1) 000ad097 28 0000 02 04 03 11 01 00c350de(1) 000ae512 28 0000 02 04 01 17 08 00c35155(1) 000ae5fc 28 0000 02 04 03 11 01 00c35156(1) 000af126 28 0000 02 04 01 17 08 00c35155(1) 000afe61 28 0000 02 04 03 11 01 00c34f64(1) 000b0bdf 28 0000 SCSI Port 2, Drive ID 4 Factory: Serial #, Firmware Rev, and Mfg/Model #: 45 32 30 41 4a 37 41 4b 00 00 00 00 00 00 00 00 E20AJ7AK........ 00 00 00 00 48 50 42 31 00 00 00 00 43 4f 4d 50 ....HPB1....COMP 41 51 20 20 42 46 30 33 36 38 37 42 35 34 20 20 AQ BF03687B54 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Since Power: Serial #, Firmware Rev, and Mfg/Model #: 45 32 30 41 4a 37 41 4b 00 00 00 00 00 00 00 00 E20AJ7AK........ 00 00 00 00 48 50 42 31 00 00 00 00 43 4f 4d 50 ....HPB1....COMP 41 51 20 20 42 46 30 33 36 38 37 42 35 34 20 20 AQ BF03687B54 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Threshold Flags: 0x0001 Serial Number Control: 0x8054 Firmware Revision Control: 0x8248 Mfg/Model Number Control: 0x8268 Factory Since Power Threshold Control Serv. Time 000e3406 000b1e95 ffffffff 8184 Read Blks 0000000aba407e92 000000010b1dcf43 8108 Hrd Read 00000000 00000000 ffffffff 8184 Rtry Read 0000000b 00000001 ffffffff 8184 ECC Read 00000000000000b8 0000000000000072 ffffffffffffffff 8188 Write Blks 0000001631005e31 0000001300ff0a14 8108 Hrd Write 00000000 00000000 ffffffff 8184 Rtry Write 00000000 00000000 ffffffff 8184 Seeks 0000000000000000 0000000000000000 8108 Seek Errs 0000000000000000 0000000000000000 ffffffffffffffff 8188 Spin Cyls 00000000 00000001 ffffffff 8184 Spin Time ffff ffff ffff 8a82 Test 1 ffff ffff ffff 0a82 Test 2 ffff ffff ffff 8a82 Test 3 ffff ffff ffff 8a82 Test 4 ffff ffff ffff 8a82 Spare Blks ffffffff ffffffff 0a04 Re-mapped fffffffe fffffffe ffffffff 8d84 DRQ Tmots ffff ffff ffff 0982 Timeouts 0000 0000 ffff 0182 Rebuilds 0000 0000 ffff 0182 Spn Retrs ffff ffff ffff 0982 Fl Rd Recv 0000 0000 ffff 8182 Fl Wt Recv 0000 0000 ffff 0182 Format Err 0000 0000 ffff 0182 POST Err ffff ffff ffff 0982 Drv Nt Ry 00000000 00000000 ffffffff 0184 Reallc Abt ffffffff ffffffff ffffffff 0984 IRQ Gltchs ffffffff ffffffff ffffffff 0984 Bus Flts 00000000 00000000 ffffffff 8184 Hot Plgs 00000000 00000000 ffffffff 0184 Tk Rwt Err ffff ffff ffff 0982 Rmp Wt Err ffff ffff ffff 0982 Bg Fw Rev 0000000000000000 0000000000000000 0a48 Med Flrs 0000 0000 ffff 0182 Hrdw Errs 0000 0000 ffff 0182 Abt Cmd Fl 0000 0000 ffff 0182 Spn Up Fl 0000 0000 ffff 0182 Bd Tgt Cnt 0000 0000 ffff 0182 Pred Fails 00000000 00000000 00000000 2184 DRIVE ERROR LOG: Error Log Header: Parameter Length = 0x14 Entry Size = 0x0014 Current Entry = 0x10 Total Errors Logged = 0x000000c4 Error Log Data: SCSI CAM Sense Sense Stat Stat Key Code Qual Block(Vl) Time Op Info ---- ---- ----- ----- ---- --------- ---- -- ---- 02 04 01 18 00 00c35111(1) 000bbffd 28 0000 02 04 01 18 00 00c34f0b(1) 000bc39c 28 0000 02 04 01 18 02 00c3511d(1) 000bcc24 28 0000 02 04 01 18 00 00c34f07(1) 000c0c1f 28 0000 02 04 01 18 02 00c3511e(1) 000c5de8 28 0000 02 04 01 18 02 00c35114(1) 000cb10f 28 0000 02 04 01 18 00 00c34f06(1) 000cd2b7 28 0000 02 04 01 18 00 00c34f09(1) 000ce331 28 0000 02 04 01 18 00 00c34f08(1) 000cf73e 28 0000 02 04 01 18 02 00c3510e(1) 000d3444 28 0000 02 04 01 18 02 00c3511f(1) 000d840a 28 0000 02 04 01 18 02 00c34f0d(1) 000d8412 28 0000 02 04 01 18 00 00c34f0a(1) 000de4e4 28 0000 02 04 01 17 00 00c3bf8a(1) 000dee44 28 0000 02 04 01 18 02 00c35112(1) 000df7ae 28 0000 02 04 01 18 00 00c35124(1) 000e1960 28 0000 02 04 01 18 00 00c34f11(1) 000b8792 28 0000 02 04 01 18 00 00c35112(1) 000ba3c5 28 0000 02 04 01 18 00 00c34f0f(1) 000ba73c 28 0000 02 04 01 18 02 00c35121(1) 000bb258 28 0000 SCSI Port 2, Drive ID 5 Factory: Serial #, Firmware Rev, and Mfg/Model #: 45 32 30 42 44 36 51 4b 00 00 00 00 00 00 00 00 E20BD6QK........ 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 37 42 35 34 20 20 AQ BF03687B54 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Since Power: Serial #, Firmware Rev, and Mfg/Model #: 45 32 30 42 44 36 51 4b 00 00 00 00 00 00 00 00 E20BD6QK........ 00 00 00 00 48 50 42 32 00 00 00 00 43 4f 4d 50 ....HPB2....COMP 41 51 20 20 42 46 30 33 36 38 37 42 35 34 20 20 AQ BF03687B54 20 20 20 20 00 00 00 00 00 00 00 00 00 00 00 00 ............ 00 00 00 00 .... Threshold Flags: 0x0001 Serial Number Control: 0x8054 Firmware Revision Control: 0x8248 Mfg/Model Number Control: 0x8268 Factory Since Power Threshold Control Serv. Time 000e3406 000b1e95 ffffffff 8184 Read Blks 0000000a974ca97d 00000000eb59c252 8108 Hrd Read 00000000 00000000 ffffffff 8184 Rtry Read 00000000 00000000 ffffffff 8184 ECC Read 0000000000000000 0000000000000000 ffffffffffffffff 8188 Write Blks 0000001492767996 00000011a01cb957 8108 Hrd Write 00000000 00000000 ffffffff 8184 Rtry Write 00000000 00000000 ffffffff 8184 Seeks 0000000000000000 0000000000000000 8108 Seek Errs 0000000000000000 0000000000000000 ffffffffffffffff 8188 Spin Cyls 00000000 00000001 ffffffff 8184 Spin Time ffff ffff ffff 8a82 Test 1 ffff ffff ffff 0a82 Test 2 ffff ffff ffff 8a82 Test 3 ffff ffff ffff 8a82 Test 4 ffff ffff ffff 8a82 Spare Blks ffffffff ffffffff 0a04 Re-mapped ffffffff ffffffff ffffffff 8d84 DRQ Tmots ffff ffff ffff 0982 Timeouts 0000 0000 ffff 0182 Rebuilds 0000 0000 ffff 0182 Spn Retrs ffff ffff ffff 0982 Fl Rd Recv 0000 0000 ffff 8182 Fl Wt Recv 0000 0000 ffff 0182 Format Err 0000 0000 ffff 0182 POST Err ffff ffff ffff 0982 Drv Nt Ry 00000000 00000000 ffffffff 0184 Reallc Abt ffffffff ffffffff ffffffff 0984 IRQ Gltchs ffffffff ffffffff ffffffff 0984 Bus Flts 00000000 00000000 ffffffff 8184 Hot Plgs 00000000 00000000 ffffffff 0184 Tk Rwt Err ffff ffff ffff 0982 Rmp Wt Err ffff ffff ffff 0982 Bg Fw Rev 0000000000000000 0000000000000000 0a48 Med Flrs 0000 0000 ffff 0182 Hrdw Errs 0000 0000 ffff 0182 Abt Cmd Fl 0000 0000 ffff 0182 Spn Up Fl 0000 0000 ffff 0182 Bd Tgt Cnt 0000 0000 ffff 0182 Pred Fails 00000000 00000000 00000000 2184 DRIVE ERROR LOG: Error Log Header: Parameter Length = 0x14 Entry Size = 0x0014 Current Entry = 0x01 Total Errors Logged = 0x00000001 Error Log Data: SCSI CAM Sense Sense Stat Stat Key Code Qual Block(Vl) Time Op Info ---- ---- ----- ----- ---- --------- ---- -- ---- 00 0e 00 00 00 00c35140(0) 000315e1 2a 0000 SCSI Port 2, Drive ID 6 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 7 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 8 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 9 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 10 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 11 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 12 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 13 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 14 Not Available DRIVE ERROR LOG: Not Available SCSI Port 2, Drive ID 15 Not Available DRIVE ERROR LOG: Not Available SURFACE ANALYSIS STATUS: Time remaining to start: 14 secs. Surface analysis delay: 15 secs. SCSI Port 1: Big Drive ID Current Block -------- ------------- 00 0x00000000 01 0x00000000 02 0x00000000 03 0x00000000 04 0x00000000 05 0x00000000 06 0x00000000 07 0x00000000 08 0x00000000 09 0x00000000 10 0x00000000 11 0x00000000 12 0x00000000 13 0x00000000 14 0x00000000 15 0x00000000 SCSI Port 2: Big Drive ID Current Block -------- ------------- 00 0x00ad1b40 01 0x00ad1b40 02 0x00ad1b40 03 0x00ad1b40 04 0x00ad1b40 05 0x00ad1b40 06 0x00000000 07 0x00000000 08 0x00000000 09 0x00000000 10 0x00000000 11 0x00000000 12 0x00000000 13 0x00000000 14 0x00000000 15 0x00000000 Big Surface Surface Logical Big Inconsistent Blocks Controller Analysis Analysis Drive Status Block Reassigned Resets Passes Pass Time ------- ------ ------------ ---------- ---------- ---------- ---------- 1 0x03 0x001bb640 4 1 579 4756 2 0x00 0x00000000 0 0 0 0 3 0x00 0x00000000 0 0 0 0 4 0x00 0x00000000 0 0 0 0 5 0x00 0x00000000 0 0 0 0 6 0x00 0x00000000 0 0 0 0 7 0x00 0x00000000 0 0 0 0 8 0x00 0x00000000 0 0 0 0 9 0x00 0x00000000 0 0 0 0 10 0x00 0x00000000 0 0 0 0 11 0x00 0x00000000 0 0 0 0 12 0x00 0x00000000 0 0 0 0 13 0x00 0x00000000 0 0 0 0 14 0x00 0x00000000 0 0 0 0 15 0x00 0x00000000 0 0 0 0 16 0x00 0x00000000 0 0 0 0 17 0x00 0x00000000 0 0 0 0 18 0x00 0x00000000 0 0 0 0 19 0x00 0x00000000 0 0 0 0 20 0x00 0x00000000 0 0 0 0 21 0x00 0x00000000 0 0 0 0 22 0x00 0x00000000 0 0 0 0 23 0x00 0x00000000 0 0 0 0 24 0x00 0x00000000 0 0 0 0 25 0x00 0x00000000 0 0 0 0 26 0x00 0x00000000 0 0 0 0 27 0x00 0x00000000 0 0 0 0 28 0x00 0x00000000 0 0 0 0 29 0x00 0x00000000 0 0 0 0 30 0x00 0x00000000 0 0 0 0 31 0x00 0x00000000 0 0 0 0 32 0x00 0x00000000 0 0 0 0 ACCELERATOR STATUS: Logical Drive Disable Map: 0x00000000 Read Cache Size: 32 MBytes Posted Write Size: 0 MBytes Disable Flag: 0x00 Status: 0x00000001 Disable Code: 0x0000 Total Memory Size: 64 MBytes Battery Count: 0 Battery Status: 0x0000 Parity Read Errors: 0000 Parity Write Errors: 0000 Error Log: N/A Failed Batteries: 0x0000 Board Present: Yes Accelerator Failure Map: 0x00000000 Max Error Log Entries: 16 NVRAM Load Status: 0x00 Memory Size Shift Factor: 0x0a Non Battery Backed Memory: 32 MBytes Memory State: 0x00 PHYSICAL DRIVE IDENTIFICATION: SCSI Port 1, Drive ID 0 ---> Not available SCSI Port 1, Drive ID 1 ---> Not available SCSI Port 1, Drive ID 2 ---> Not available SCSI Port 1, Drive ID 3 ---> Not available SCSI Port 1, Drive ID 4 ---> Not available SCSI Port 1, Drive ID 5 ---> Not available SCSI Port 1, Drive ID 6 ---> Not available SCSI Port 1, Drive ID 7 ---> Not available SCSI Port 1, Drive ID 8 ---> Not available SCSI Port 1, Drive ID 9 ---> Not available SCSI Port 1, Drive ID 10 ---> Not available SCSI Port 1, Drive ID 11 ---> Not available SCSI Port 1, Drive ID 12 ---> Not available SCSI Port 1, Drive ID 13 ---> Not available SCSI Port 1, Drive ID 14 ---> Not available SCSI Port 1, Drive ID 15 ---> Not available SCSI Port 2, Drive ID 0 Vendor Id: COMPAQ Product Id: BF03688575 Product Rev: HPB2 Vendor Specific: ANL1P55062MV Serial Number: ANL1P55062MV0521 SCSI Inquiry Header: 00 00 03 12 5b 00 01 3a Device Supports: Tagged Command Queueing Linked Commands Synchronous Data Transfer 16-bit Wide Data Transfer Drive Type: 0x00 Parallel SCSI Block Size: 512 bytes/sector Total Blocks: 71123808 sectors/disk Reserved Blocks: 1088 reserved sectors/disk SCSI Inquiry Bits: 0x3A Stamped for M&P: yes Last Failure Reason: 0x00 (Drive has not failed) Phys Drive Flags: 0xcd 0x25 0x9d 0x07 Drive present and operational Wide SCSI transfers Enabled Ultra320 SCSI Enabled S.M.A.R.T. Supported S.M.A.R.T. Enabled Quick Arbitration and Selection Capable Quick Arbitration and Selection enabled Arbitration Fairness enabled Configured as part of Logical Drive Drive write cache is currently disabled Drive write cache setting is changeable and safe SCSI LUN: 0 Spi Speed Rules: 0xbc9b0800 Physical Connector: J2 (controller connector attached to drive) Physical Box on Bus: 0 (number of the physical enclosure in which drive resides) Physical Bay in Box: 0 (number of the physical drive bay in the enclosure) MODE SENSE: Header: 00 d2 00 10 00 00 00 08 00 00 00 00 00 00 02 00 Page 01: 81 0a e4 3f ff 00 00 00 3f 00 75 30 Page 02: 82 0e 00 00 00 01 00 00 00 00 00 00 70 00 00 00 Page 03: 83 16 00 36 00 c8 00 00 00 24 03 5f 02 00 00 01 00 d8 00 6f 40 00 00 00 Page 04: 84 16 00 c0 06 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3a 98 00 00 Page 07: 87 0a 04 3f ff 00 00 00 00 00 75 30 Page 08: 88 12 10 00 ff ff 00 00 00 00 ff ff 80 08 00 00 00 00 00 00 Page 09: 89 0e 00 00 00 00 00 00 00 00 00 00 00 00 04 00 Page 0a: 8a 0a 00 10 00 00 00 00 00 00 03 d8 Page 0c: 0c 16 80 00 00 12 00 00 00 00 00 00 00 c0 05 01 00 00 00 00 00 00 00 08 Page 19: 99 06 01 00 00 00 00 00 Page 1a: 9a 0a 00 00 ff ff ff ff ff ff ff ff Page 1c: 9c 0a 11 04 00 00 0b b8 00 00 00 02 Page 21: a1 02 0f 00 SCSI Port 2, Drive ID 1 Vendor Id: COMPAQ Product Id: BF03688575 Product Rev: HPB2 Vendor Specific: ANL1P5505UCE Serial Number: ANL1P5505UCE0520 SCSI Inquiry Header: 00 00 03 12 5b 00 01 3a Device Supports: Tagged Command Queueing Linked Commands Synchronous Data Transfer 16-bit Wide Data Transfer Drive Type: 0x00 Parallel SCSI Block Size: 512 bytes/sector Total Blocks: 71123808 sectors/disk Reserved Blocks: 1088 reserved sectors/disk SCSI Inquiry Bits: 0x3A Stamped for M&P: yes Last Failure Reason: 0x00 (Drive has not failed) Phys Drive Flags: 0xcd 0x25 0x9d 0x07 Drive present and operational Wide SCSI transfers Enabled Ultra320 SCSI Enabled S.M.A.R.T. Supported S.M.A.R.T. Enabled Quick Arbitration and Selection Capable Quick Arbitration and Selection enabled Arbitration Fairness enabled Configured as part of Logical Drive Drive write cache is currently disabled Drive write cache setting is changeable and safe SCSI LUN: 0 Spi Speed Rules: 0xbc9b0800 Physical Connector: J2 (controller connector attached to drive) Physical Box on Bus: 0 (number of the physical enclosure in which drive resides) Physical Bay in Box: 1 (number of the physical drive bay in the enclosure) MODE SENSE: Header: 00 d2 00 10 00 00 00 08 00 00 00 00 00 00 02 00 Page 01: 81 0a e4 3f ff 00 00 00 3f 00 75 30 Page 02: 82 0e 00 00 00 01 00 00 00 00 00 00 70 00 00 00 Page 03: 83 16 00 36 00 c8 00 00 00 24 03 5f 02 00 00 01 00 d8 00 6f 40 00 00 00 Page 04: 84 16 00 c0 06 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3a 98 00 00 Page 07: 87 0a 04 3f ff 00 00 00 00 00 75 30 Page 08: 88 12 10 00 ff ff 00 00 00 00 ff ff 80 08 00 00 00 00 00 00 Page 09: 89 0e 00 00 00 00 00 00 00 00 00 00 00 00 04 00 Page 0a: 8a 0a 00 10 00 00 00 00 00 00 03 d8 Page 0c: 0c 16 80 00 00 12 00 00 00 00 00 00 00 c0 05 01 00 00 00 00 00 00 00 08 Page 19: 99 06 01 00 00 00 00 00 Page 1a: 9a 0a 00 00 ff ff ff ff ff ff ff ff Page 1c: 9c 0a 11 04 00 00 0b b8 00 00 00 02 Page 21: a1 02 0f 00 SCSI Port 2, Drive ID 2 Vendor Id: COMPAQ Product Id: BF03688575 Product Rev: HPB2 Vendor Specific: ANL1P55061YW Serial Number: ANL1P55061YW0521 SCSI Inquiry Header: 00 00 03 12 5b 00 01 3a Device Supports: Tagged Command Queueing Linked Commands Synchronous Data Transfer 16-bit Wide Data Transfer Drive Type: 0x00 Parallel SCSI Block Size: 512 bytes/sector Total Blocks: 71123808 sectors/disk Reserved Blocks: 1088 reserved sectors/disk SCSI Inquiry Bits: 0x3A Stamped for M&P: yes Last Failure Reason: 0x00 (Drive has not failed) Phys Drive Flags: 0xcd 0x25 0x9d 0x07 Drive present and operational Wide SCSI transfers Enabled Ultra320 SCSI Enabled S.M.A.R.T. Supported S.M.A.R.T. Enabled Quick Arbitration and Selection Capable Quick Arbitration and Selection enabled Arbitration Fairness enabled Configured as part of Logical Drive Drive write cache is currently disabled Drive write cache setting is changeable and safe SCSI LUN: 0 Spi Speed Rules: 0xbc9b0800 Physical Connector: J2 (controller connector attached to drive) Physical Box on Bus: 0 (number of the physical enclosure in which drive resides) Physical Bay in Box: 2 (number of the physical drive bay in the enclosure) MODE SENSE: Header: 00 d2 00 10 00 00 00 08 00 00 00 00 00 00 02 00 Page 01: 81 0a e4 3f ff 00 00 00 3f 00 75 30 Page 02: 82 0e 00 00 00 01 00 00 00 00 00 00 70 00 00 00 Page 03: 83 16 00 36 00 c8 00 00 00 24 03 5f 02 00 00 01 00 d8 00 6f 40 00 00 00 Page 04: 84 16 00 c0 06 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3a 98 00 00 Page 07: 87 0a 04 3f ff 00 00 00 00 00 75 30 Page 08: 88 12 10 00 ff ff 00 00 00 00 ff ff 80 08 00 00 00 00 00 00 Page 09: 89 0e 00 00 00 00 00 00 00 00 00 00 00 00 04 00 Page 0a: 8a 0a 00 10 00 00 00 00 00 00 03 d8 Page 0c: 0c 16 80 00 00 12 00 00 00 00 00 00 00 c0 05 01 00 00 00 00 00 00 00 08 Page 19: 99 06 01 00 00 00 00 00 Page 1a: 9a 0a 00 00 ff ff ff ff ff ff ff ff Page 1c: 9c 0a 11 04 00 00 0b b8 00 00 00 02 Page 21: a1 02 0f 00 SCSI Port 2, Drive ID 3 Vendor Id: COMPAQ Product Id: BF03688575 Product Rev: HPB2 Vendor Specific: ANL1P5606RN9 Serial Number: ANL1P5606RN90523 SCSI Inquiry Header: 00 00 03 12 5b 00 01 3a Device Supports: Tagged Command Queueing Linked Commands Synchronous Data Transfer 16-bit Wide Data Transfer Drive Type: 0x00 Parallel SCSI Block Size: 512 bytes/sector Total Blocks: 71123808 sectors/disk Reserved Blocks: 1088 reserved sectors/disk SCSI Inquiry Bits: 0x3A Stamped for M&P: yes Last Failure Reason: 0x14 (Drive removed from hot plug) Phys Drive Flags: 0xcd 0x25 0x9d 0x07 Drive present and operational Wide SCSI transfers Enabled Ultra320 SCSI Enabled S.M.A.R.T. Supported S.M.A.R.T. Enabled Quick Arbitration and Selection Capable Quick Arbitration and Selection enabled Arbitration Fairness enabled Configured as part of Logical Drive Drive write cache is currently disabled Drive write cache setting is changeable and safe SCSI LUN: 0 Spi Speed Rules: 0xbc9b0800 Physical Connector: J2 (controller connector attached to drive) Physical Box on Bus: 0 (number of the physical enclosure in which drive resides) Physical Bay in Box: 3 (number of the physical drive bay in the enclosure) MODE SENSE: Header: 00 d2 00 10 00 00 00 08 00 00 00 00 00 00 02 00 Page 01: 81 0a e4 3f ff 00 00 00 3f 00 75 30 Page 02: 82 0e 00 00 00 01 00 00 00 00 00 00 70 00 00 00 Page 03: 83 16 00 36 00 c8 00 00 00 24 03 5f 02 00 00 01 00 d8 00 6f 40 00 00 00 Page 04: 84 16 00 c0 06 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 3a 98 00 00 Page 07: 87 0a 04 3f ff 00 00 00 00 00 75 30 Page 08: 88 12 10 00 ff ff 00 00 00 00 ff ff 80 08 00 00 00 00 00 00 Page 09: 89 0e 00 00 00 00 00 00 00 00 00 00 00 00 04 00 Page 0a: 8a 0a 00 10 00 00 00 00 00 00 03 d8 Page 0c: 0c 16 80 00 00 12 00 00 00 00 00 00 00 c0 05 01 00 00 00 00 00 00 00 08 Page 19: 99 06 01 00 00 00 00 00 Page 1a: 9a 0a 00 00 ff ff ff ff ff ff ff ff Page 1c: 9c 0a 11 04 00 00 0b b8 00 00 00 02 Page 21: a1 02 0f 00 SCSI Port 2, Drive ID 4 Vendor Id: COMPAQ Product Id: BF03687B54 Product Rev: HPB1 Vendor Specific: E20AJ7AK 00003 Serial Number: E20AJ7AK SCSI Inquiry Header: 00 00 03 12 5b 00 01 3e Device Supports: Tagged Command Queueing Linked Commands Synchronous Data Transfer 16-bit Wide Data Transfer Drive Type: 0x00 Parallel SCSI Block Size: 512 bytes/sector Total Blocks: 71123808 sectors/disk Reserved Blocks: 1088 reserved sectors/disk SCSI Inquiry Bits: 0x3E Stamped for M&P: yes Last Failure Reason: 0x00 (Drive has not failed) Phys Drive Flags: 0xcd 0x25 0x9d 0x07 Drive present and operational Wide SCSI transfers Enabled Ultra320 SCSI Enabled S.M.A.R.T. Supported S.M.A.R.T. Enabled Quick Arbitration and Selection Capable Quick Arbitration and Selection enabled Arbitration Fairness enabled Configured as part of Logical Drive Drive write cache is currently disabled Drive write cache setting is changeable and safe SCSI LUN: 0 Spi Speed Rules: 0xbc9b0800 Physical Connector: J2 (controller connector attached to drive) Physical Box on Bus: 0 (number of the physical enclosure in which drive resides) Physical Bay in Box: 4 (number of the physical drive bay in the enclosure) MODE SENSE: Header: 00 d2 00 10 00 00 00 08 00 00 00 00 00 00 02 00 Page 01: 81 0a e4 04 f0 00 00 00 08 00 00 00 Page 02: 82 0e 00 00 00 00 00 00 00 00 00 00 70 00 00 00 Page 03: 83 16 00 02 00 00 00 00 00 00 02 70 02 00 00 01 00 37 00 37 40 00 00 00 Page 04: 84 16 00 bc 72 02 00 bc 72 00 00 00 00 00 00 bc 72 00 00 00 3a a8 00 00 Page 07: 87 0a 04 04 f0 00 00 00 00 00 00 00 Page 08: 88 12 00 00 02 00 01 00 02 00 02 00 10 e2 00 00 00 00 00 00 Page 09: 89 0e 00 00 00 00 00 00 00 00 00 00 00 00 04 00 Page 0a: 8a 0a 00 10 00 00 00 00 00 00 02 d0 Page 0c: 8c 16 80 00 00 10 00 00 00 00 00 00 00 bc 71 01 00 00 00 00 00 00 10 08 Page 19: 99 06 01 00 00 00 00 00 Page 1a: 9a 0a 00 00 ff ff ff ff ff ff ff ff Page 1c: 9c 0a 91 04 00 00 0b b8 00 00 00 02 Page 00: 80 02 00 00 SCSI Port 2, Drive ID 5 Vendor Id: COMPAQ Product Id: BF03687B54 Product Rev: HPB2 Vendor Specific: E20BD6QK 00003 Serial Number: E20BD6QK SCSI Inquiry Header: 00 00 03 12 5b 00 01 3e Device Supports: Tagged Command Queueing Linked Commands Synchronous Data Transfer 16-bit Wide Data Transfer Drive Type: 0x00 Parallel SCSI Block Size: 512 bytes/sector Total Blocks: 71123808 sectors/disk Reserved Blocks: 1088 reserved sectors/disk SCSI Inquiry Bits: 0x3E Stamped for M&P: yes Last Failure Reason: 0x00 (Drive has not failed) Phys Drive Flags: 0xcd 0x25 0x9d 0x07 Drive present and operational Wide SCSI transfers Enabled Ultra320 SCSI Enabled S.M.A.R.T. Supported S.M.A.R.T. Enabled Quick Arbitration and Selection Capable Quick Arbitration and Selection enabled Arbitration Fairness enabled Configured as part of Logical Drive Drive write cache is currently disabled Drive write cache setting is changeable and safe SCSI LUN: 0 Spi Speed Rules: 0xbc9b0800 Physical Connector: J2 (controller connector attached to drive) Physical Box on Bus: 0 (number of the physical enclosure in which drive resides) Physical Bay in Box: 5 (number of the physical drive bay in the enclosure) MODE SENSE: Header: 00 d2 00 10 00 00 00 08 00 00 00 00 00 00 02 00 Page 01: 81 0a e4 04 f0 00 00 00 08 00 00 00 Page 02: 82 0e 00 00 00 00 00 00 00 00 00 00 70 00 00 00 Page 03: 83 16 00 02 00 00 00 00 00 00 02 70 02 00 00 01 00 37 00 37 40 00 00 00 Page 04: 84 16 00 bc 72 02 00 bc 72 00 00 00 00 00 00 bc 72 00 00 00 3a a8 00 00 Page 07: 87 0a 04 04 f0 00 00 00 00 00 00 00 Page 08: 88 12 00 00 02 00 01 00 02 00 02 00 10 e2 00 00 00 00 00 00 Page 09: 89 0e 00 00 00 00 00 00 00 00 00 00 00 00 04 00 Page 0a: 8a 0a 00 10 00 00 00 00 00 00 02 d0 Page 0c: 8c 16 80 00 00 10 00 00 00 00 00 00 00 bc 71 01 00 00 00 00 00 00 10 08 Page 19: 99 06 01 00 00 00 00 00 Page 1a: 9a 0a 00 00 ff ff ff ff ff ff ff ff Page 1c: 9c 0a 91 04 00 00 0b b8 00 00 00 02 Page 00: 80 02 00 00 SCSI Port 2, Drive ID 6 ---> Not available SCSI Port 2, Drive ID 7 ---> Not available SCSI Port 2, Drive ID 8 ---> Not available SCSI Port 2, Drive ID 9 ---> Not available SCSI Port 2, Drive ID 10 ---> Not available SCSI Port 2, Drive ID 11 ---> Not available SCSI Port 2, Drive ID 12 ---> Not available SCSI Port 2, Drive ID 13 ---> Not available SCSI Port 2, Drive ID 14 ---> Not available SCSI Port 2, Drive ID 15 ---> Not available CONTROLLER PARAMETERS: LED Control: 0x00 Command List Verification: On Backed-out Write drives: 0 Stripes for Parity: 0 Distribution Mode: 0x00 Maximum Driver Requests: 0xffff Elevator Trend Count: 0x0032 Disable Elevator: 0x00 Force Scan Complete: 0x00 Synch/Asynch Mode: Auto Detect Force Narrow: No Rebuild Priority: 0 Expand Priority: 0 SDB ASIC Fix: 0x00 PDIP Burst Disable: 0x00 Software Name: Hardware Name: SCSI BUS 1 PARAMETERS: Inquiry Data Valid: No Hot Plug Counts: All counts are zero Fan Alert Count: 0x0000 Alarm Status: 0x00 (No Alarms) Temperature Status: 0x00 Valid Alarm Bits: 0x00 Alarm Count: 0000 Specific Counts: 00000 00000 00000 00000 00000 00000 00000 00000 Connection Info: 0x0000 SCSI Device Rev: 0x01 Fan Status: 0x0000 More Inquiry Data: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ SCSI Device Type: 0x00460e11 (unknown) Interrupt Count: 00000000 Ultra Bus Faults: 0x00000000 SCSI Initiator ID: 7 SCSI Target ID: 7 Chassis Serial Number: Not Available Physical Connector: J3 (controller connector attached to drive) Big Inst Drive Map: 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Big Bus Map: 0xffff 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 More Connection Info: 0x01 (LVD SCSI bus enabled) Extended Powersupply / Fan Information not available on this unit SCSI BUS 2 PARAMETERS: Inquiry Data Valid: Yes Inquiry Header: 03 00 02 02 23 00 00 00 Vendor Id: COMPAQ Product Id: PROLIANT 6L6I Product Rev: 0.10 Hot Plug Counts: Drive 03: 0x0001 Fan Alert Count: 0x0000 Alarm Status: 0x00 (No Alarms) Temperature Status: 0x00 Valid Alarm Bits: 0x00 Alarm Count: 0000 Specific Counts: 00000 00000 00000 00000 00000 00000 00000 00000 Connection Info: 0x010a SCSI Device Rev: 0x01 Fan Status: 0x0000 More Inquiry Data: 03 2e 00 90 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ SCSI Device Type: 0x00460e11 (unknown) Interrupt Count: 00000002 Ultra Bus Faults: 0x00000000 SCSI Initiator ID: 7 SCSI Target ID: 7 Chassis Serial Number: Not Available Physical Connector: J2 (controller connector attached to drive) Big Inst Drive Map: 0x0000 0x003f 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 Big Bus Map: 0x0000 0xffff 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 More Connection Info: 0x01 (LVD SCSI bus enabled) Extended Powersupply / Fan Information not available on this unit PARTITION TABLES: SCSI Port 2, Drive ID 0: 80 01 01 00 83 fe bf 5f 3f 00 00 00 21 0a 95 00 (Start C/H/S 0000/001/01, End 0607/254/63) 00 00 81 60 82 fe ff 52 60 0a 95 00 33 91 3b 00 (Start C/H/S 0608/000/01, End 0850/254/63) 00 00 c1 53 83 fe ff ff 93 9b d0 00 0e ff e6 0b (Start C/H/S 0851/000/01, End 1023/254/63) 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SCSI Port 2, Drive ID 3: ---> Same as above. RIS DATA AREA: SCSI Port 1, Drive ID 0: Physical drive not connected. SCSI Port 1, Drive ID 1: Physical drive not connected. SCSI Port 1, Drive ID 2: Physical drive not connected. SCSI Port 1, Drive ID 3: Physical drive not connected. SCSI Port 1, Drive ID 4: Physical drive not connected. SCSI Port 1, Drive ID 5: Physical drive not connected. SCSI Port 1, Drive ID 6: Physical drive not connected. SCSI Port 1, Drive ID 7: Physical drive not connected. SCSI Port 1, Drive ID 8: Physical drive not connected. SCSI Port 1, Drive ID 9: Physical drive not connected. SCSI Port 1, Drive ID 10: Physical drive not connected. SCSI Port 1, Drive ID 11: Physical drive not connected. SCSI Port 1, Drive ID 12: Physical drive not connected. SCSI Port 1, Drive ID 13: Physical drive not connected. SCSI Port 1, Drive ID 14: Physical drive not connected. SCSI Port 1, Drive ID 15: Physical drive not connected. SCSI Port 2, Drive ID 0: RIS drive: 0x10 RIS Copy 0: Drive id: 16 RIS signature: ASTROS Physical Drives: 6 Logical Drives: 1 Physical Drive State: (00=OK, 01=bad or not present, 02=replacement) 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 00 00 00 00 00 00 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 Signature: 0xa01457b3 RIS version: 1501 Logical Drive State: (00=OK, 01=failed, 02=unused) 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 RIS updates: 1303 Remap interrupted: 0 Surface delay: 150 Overheat delay: 0 M&P delay: 60 RIS hex dump: Not included in this ADU report! RIS Copy 1: Same as above. SCSI Port 2, Drive ID 1: RIS drive: 0x11 RIS Copy 0: Same as above. RIS Copy 1: Same as above. SCSI Port 2, Drive ID 2: RIS drive: 0x12 RIS Copy 0: Same as above. RIS Copy 1: Same as above. SCSI Port 2, Drive ID 3: RIS drive: 0x13 RIS Copy 0: Same as above. RIS Copy 1: Same as above. SCSI Port 2, Drive ID 4: RIS drive: 0x14 RIS Copy 0: Same as above. RIS Copy 1: Same as above. SCSI Port 2, Drive ID 5: RIS drive: 0x15 RIS Copy 0: Same as above. RIS Copy 1: Same as above. SCSI Port 2, Drive ID 6: Physical drive not connected. SCSI Port 2, Drive ID 7: Physical drive not connected. SCSI Port 2, Drive ID 8: Physical drive not connected. SCSI Port 2, Drive ID 9: Physical drive not connected. SCSI Port 2, Drive ID 10: Physical drive not connected. SCSI Port 2, Drive ID 11: Physical drive not connected. SCSI Port 2, Drive ID 12: Physical drive not connected. SCSI Port 2, Drive ID 13: Physical drive not connected. SCSI Port 2, Drive ID 14: Physical drive not connected. SCSI Port 2, Drive ID 15: Physical drive not connected.