****************************************************************************** **** **** **** S A U T I L S u p p o r t U t i l i t y **** **** **** **** for the HP SmartArray RAID Controller Family **** **** **** **** version A.02.06 **** **** **** **** (C) Copyright 2003, 2004 Hewlett-Packard Development Company, L.P. **** ****************************************************************************** ---- DRIVER INFORMATION ------------------------------------------------------ Driver State........................ READY ---- CONTROLLER INFORMATION -------------------------------------------------- Controller Product Number........... A9890A Controller Product Name............. HP PCI-X SmartArray 6402 Hardware Path....................... 0/4/1/0/4/0 Serial Number....................... P57820P9SRF0RT Device File......................... /dev/ciss4 Hardware Revision................... 'B' Boot Block Revision................. 3.86 Firmware Revision (running)......... 2.34 Firmware Revision (in ROM).......... 2.34 Firmware Revision (inactive)........ 2.34 # of Logical Drives................. 2 # of Physical Disks Configured...... 12 # of Physical Disks Detected........ 11 Logical Drive Rebuild Priority...... 118 (high) Array Capacity Expansion Priority... 0 (low) Auto-Fail Missing Disks at Boot..... enabled SCSI Transfer Detection Mode........ Auto Detect ---- ARRAY ACCELERATOR (CACHE) INFORMATION ----------------------------------- Array Accelerator Board Present?.... yes Cache Configuration Status.......... write cache temporarily disabled (code=1) Cache Ratio......................... 50% Read / 50% Write Total Cache Size (MB)............... 128 Read Cache........................ 064 Write Cache....................... 064 Transfer Buffer................... 000 Battery Pack Count.................. 2 Battery Status (pack #1)............ FAILED Battery Status (pack #2)............ FAILED ---- LOGICAL DRIVE SUMMARY --------------------------------------------------- # RAID Size Status 0 5 840059 MB OK 1 5 560039 MB FAILED ---- SCSI DEVICE SUMMARY ----------------------------------------------------- Location Ch ID Type Capacity Status external 1 0 DISK 146.8 GB OK external 1 1 DISK 146.8 GB OK external 1 2 DISK 146.8 GB OK external 1 3 DISK 146.8 GB OK external 1 4 DISK 146.8 GB OK external 1 5 DISK 146.8 GB OK external 1 8 DISK 146.8 GB OK external 1 15 PROCESSOR external 2 0 DISK 146.8 GB OK external 2 1 DISK 146.8 GB OK N/A 2 2 N/A N/A FAILED N/A 2 3 N/A N/A FAILED N/A 2 4 N/A N/A FAILED external 2 5 DISK 146.8 GB UNASSIGNED external 2 7 PROCESSOR external 2 8 DISK 146.8 GB UNASSIGNED ---- SCSI BUS SUMMARY -------------------------------------------------------- External Internal Ch LVD_Mode Connector Connector 1 YES YES - 2 YES YES - ---- LOGICAL DRIVE 0 --------------------------------------------------------- Fault Tolerance Mode................ RAID 5 (Distributed Data Guarding) Logical Drive Size.................. 840059 MB Logical Drive Status................ OK # of Participating Physical Disks... 7 Participating Physical Disk(s)...... Ch:ID 1: 0 1: 1 1: 2 1: 3 1: 4 1: 5 1: 8 Participating Spare Disk(s)......... Ch:ID none Stripe Size......................... 16 KB Logical Drive Cache Status.......... write cache temporarily disabled (code=1) Configuration Signature............. 0x0 Media Exchange Detected?............ no ---- LOGICAL DRIVE 1 --------------------------------------------------------- Fault Tolerance Mode................ RAID 5 (Distributed Data Guarding) Logical Drive Size.................. 560039 MB Logical Drive Status................ FAILED # of Participating Physical Disks... 5 Participating Physical Disk(s)...... Ch:ID 2: 0 2: 1 2: 2 <-- NOT RESPONDING 2: 3 <-- NOT RESPONDING 2: 4 <-- NOT RESPONDING Participating Spare Disk(s)......... Ch:ID none Stripe Size......................... 64 KB Logical Drive Cache Status.......... write cache temporarily disabled (code=1) Configuration Signature............. 0x0 Media Exchange Detected?............ yes ---- SCSI DEVICE 1:0 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 0 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD14688278 Device Serial Number............................. 3KS1G4XG00007548XV6S Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:1 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 1 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD14688278 Device Serial Number............................. 3KS1H5B900007549QMNL Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:2 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 2 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD14688278 Device Serial Number............................. 3KS1FR6W00007549TGR2 Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:3 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 3 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD14688278 Device Serial Number............................. 3KS1HXBW00007549VH0K Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:4 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 4 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD14688278 Device Serial Number............................. 3KS1JZQG00007549Z4J4 Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:5 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 5 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD14688278 Device Serial Number............................. 3KS1EGFL00007549Z415 Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:8 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 8 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD14688278 Device Serial Number............................. 3KS1HX9A00007548VRTE Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. TIMEOUT Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:15 [PROCESSOR] -------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 15 Device Type...................................... PROCESSOR Device Vendor ID................................. COMPAQ Device Product ID................................ PROLIANT 4L7E*DB SCSI Transfer Rate (maximum)..................... Ultra-320 ---- SCSI DEVICE 2:0 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 0 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD14686225 Device Serial Number............................. ECWME9ME Device Firmware Version.......................... HPB6 SCSI Transfer Rate (actual)...................... Ultra Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ no Last Failure Reason.............................. TIMEOUT Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. no S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... no Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... no Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:1 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 1 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD14686225 Device Serial Number............................. ECWWVNTE Device Firmware Version.......................... HPB6 SCSI Transfer Rate (actual)...................... Ultra Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ no Last Failure Reason.............................. TIMEOUT Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. no S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... no Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... no Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:5 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 5 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... UNASSIGNED Device Vendor ID................................. COMPAQ Device Product ID................................ BD14686225 Device Serial Number............................. ECWEXS2E Device Firmware Version.......................... HPB6 SCSI Transfer Rate (actual)...................... Ultra Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ no Last Failure Reason.............................. BUS RESET RECOVERY ABORTED Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. no S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. no Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... no Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... no Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:7 [PROCESSOR] --------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 7 Device Type...................................... PROCESSOR Device Vendor ID................................. COMPAQ Device Product ID................................ PROLIANT 4L7E DT SCSI Transfer Rate (maximum)..................... Ultra-320 ---- SCSI DEVICE 2:8 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 8 Device Type...................................... DISK Disk Capacity.................................... 146.8 GB Device Status.................................... UNASSIGNED Device Vendor ID................................. COMPAQ Device Product ID................................ BD14686225 Device Serial Number............................. ECW6XKGC Device Firmware Version.......................... HPB6 SCSI Transfer Rate (actual)...................... Ultra Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ no Last Failure Reason.............................. REMOVED IN HOT PLUG Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. no S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. no Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... no Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... no Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- DIAGRAM OF EXTERNAL CONNECTORS ON BRACKET ------------------------------- ========---======== | | | U320 <--- LOOK FOR THIS LOGO | / \ | | <- | | \ / | | | | * * | | * * * * | (Ch A1)---> * * * * <--- (Ch A2) | * * * * | | * * | | | | | | | | | | | | | | | | | | | ~ ~ ~ ~ ~ ****************************************************************************** **** End of SAUTIL Output **** ******************************************************************************