show connections Connection Name: Titan-sw2-p1 Host WWNN = 210000E0-8B841A41 Host WWPN = 210000E0-8B841A41 Profile Name = Linux Unit Offset = 0 Connection Name: Rhea-sw2-p2 Host WWNN = 210000E0-8B84DE40 Host WWPN = 210000E0-8B84DE40 Profile Name = Linux Unit Offset = 0 Connection Name: Titan-sw1-p1 Host WWNN = 210000E0-8B8526AA Host WWPN = 210000E0-8B8526AA Profile Name = Linux Unit Offset = 0 Connection Name: Rhea-sw1-p2 Host WWNN = 210000E0-8B85B3B2 Host WWPN = 210000E0-8B85B3B2 Profile Name = Linux Unit Offset = 0 sho Invalid CLI command. CLI> show this_controller Controller: MSA1000(c) Compaq P56350HX3S80O3 Software 4.48 Build 342 Hardware 7 Controller Identifier: NODE_ID = 500805F3-001847A0 SCSI_VERSION = SCSI-3 Supported Redundancy Mode: Active/Standby Current Redundancy Mode: Active/Standby Current Role: Active Device Port SCSI address 6 Terminal speed for the CLI is set to 19200. Host Port_1: REPORTED PORT_ID 500805F3-001847A1 PORT_1_TOPOLOGY = F_Port Cache: 128 megabyte read cache 128 megabyte write cache Version 2 Cache is GOOD, and Cache is enabled. No unflushed data in cache Battery: Module #1 is fully charged and turned off. Controller Up Time: 0 Days 02 Hours 59 Minutes 59 Seconds CLI> show other_controller Controller: MSA1000(c) Compaq P56350HX3SJ049 Software 4.48 Build 342 Hardware 7 Controller Identifier: NODE_ID = 500805F3-001847A0 SCSI_VERSION = SCSI-3 Supported Redundancy Mode: Active/Standby Current Redundancy Mode: Active/Standby Current Role: Standby Device Port SCSI address 7 Terminal speed for the CLI is set to 19200. Host Port_1: REPORTED PORT_ID 500805F3-001847A9 PORT_1_TOPOLOGY = F_Port Cache: 128 megabyte read cache 128 megabyte write cache Version 2 Cache is GOOD, and Cache is enabled. No unflushed data in cache Battery: Module #1 is fully charged and turned off. Controller Up Time: 0 Days 03 Hours 00 Minutes 19 Seconds CLI> show disks box,bay bus,ID Size Speed Units Disk101 1,01 0,00 146.8 GB 160 MB/s 0 Disk102 1,02 0,01 146.8 GB 160 MB/s 0 Disk103 1,03 0,02 146.8 GB 160 MB/s 0 Disk104 1,04 0,03 146.8 GB 160 MB/s 0 Disk105 1,05 0,04 146.8 GB 160 MB/s 0 Disk106 1,06 0,05 146.8 GB 160 MB/s 1 Disk107 1,07 0,08 146.8 GB 160 MB/s 1 Disk108 1,08 1,00 146.8 GB 160 MB/s 0 Disk109 1,09 1,01 146.8 GB 160 MB/s 0 Disk110 1,10 1,02 146.8 GB 160 MB/s 0 Disk111 1,11 1,03 146.8 GB 160 MB/s 0 Disk112 1,12 1,04 146.8 GB 160 MB/s 0 Disk113 1,13 1,05 146.8 GB 160 MB/s 1 Disk114 1,14 1,08 146.8 GB 160 MB/s 1 Disk201 2,01 2,00 146.8 GB 160 MB/s none Disk202 2,02 2,01 146.8 GB 160 MB/s none Disk203 2,03 2,02 146.8 GB 160 MB/s none Disk204 2,04 2,03 146.8 GB 160 MB/s none Disk205 2,05 2,04 146.8 GB 160 MB/s none Disk206 2,06 2,05 146.8 GB 160 MB/s none Disk207 2,07 2,08 146.8 GB 160 MB/s none Disk208 2,08 2,09 146.8 GB 160 MB/s none Disk209 2,09 2,10 146.8 GB 160 MB/s none Disk210 2,10 2,11 146.8 GB 160 MB/s none Disk211 2,11 2,12 146.8 GB 160 MB/s none Disk212 2,12 2,13 146.8 GB 160 MB/s none Disk213 2,13 2,14 146.8 GB 160 MB/s none Disk214 2,14 2,15 146.8 GB 160 MB/s none Notes: The speed is the currently negotiated speed to the disk. This may be less than the maximum speed supported by the device due to bus faults, loss of signal integrity, etc. CLI> show units Unit 0: In PDLA mode, Unit 0 is Lun 1; In VSA mode, Unit 0 is Lun 0. Unit Identifier : Device Identifier : 600805F3-001847A0-A3030FD4-894F0000 Cache Status : Enabled Max Boot Partition: Disabled Volume Status : VOLUME OK Parity Init Status: Complete 10 Data Disk(s) used by lun 0: Disk101: Box 1, Bay 01, (SCSI bus 0, SCSI id 0) Disk102: Box 1, Bay 02, (SCSI bus 0, SCSI id 1) Disk103: Box 1, Bay 03, (SCSI bus 0, SCSI id 2) Disk104: Box 1, Bay 04, (SCSI bus 0, SCSI id 3) Disk105: Box 1, Bay 05, (SCSI bus 0, SCSI id 4) Disk108: Box 1, Bay 08, (SCSI bus 1, SCSI id 0) Disk109: Box 1, Bay 09, (SCSI bus 1, SCSI id 1) Disk110: Box 1, Bay 10, (SCSI bus 1, SCSI id 2) Disk111: Box 1, Bay 11, (SCSI bus 1, SCSI id 3) Disk112: Box 1, Bay 12, (SCSI bus 1, SCSI id 4) Spare Disk(s) used by lun 0: No spare drive is designated. Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (Raid 5) stripe_size=16kB Logical Volume Capacity : 1,260,124MB Unit 1: In PDLA mode, Unit 1 is Lun 2; In VSA mode, Unit 1 is Lun 1. Unit Identifier : Device Identifier : 600805F3-001847A0-A2E332C8-6E3E0001 Cache Status : Enabled Max Boot Partition: Disabled Volume Status : VOLUME OK Parity Init Status: Complete 4 Data Disk(s) used by lun 1: Disk106: Box 1, Bay 06, (SCSI bus 0, SCSI id 5) Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8) Disk113: Box 1, Bay 13, (SCSI bus 1, SCSI id 5) Disk114: Box 1, Bay 14, (SCSI bus 1, SCSI id 8) Spare Disk(s) used by lun 1: No spare drive is designated. Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (Raid 5) stripe_size=16kB Logical Volume Capacity : 420,041MB CLI> sow tech_support Invalid CLI command. CLI> show tech_sy upport CLI> show version Firmware version: 4.48 build 342 Hardware Revision: 7 [AutoRev: 0x010000] Internal EMU Rev: 1.86 (SGM054201C) External Box EMU 2 Rev: CP20 (MHSTLMPX6R) CLI> show profile Profile name = Default (Default) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor field contains Compaq Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Ignore Force Unit Access on Write Profile name = Windows Type = Standard Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor field contains Compaq Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Ignore Force Unit Access on Write Profile name = Windows (degraded performance) Type = Custom Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor field contains Compaq Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Profile name = OpenVMS Type = Custom Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' Mode 4 = VMS shadow style bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor field contains Compaq Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Profile name = Tru64 Type = Standard Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor field contains Compaq Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Profile name = Linux Type = Standard Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor field contains Compaq Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Profile name = Solaris Type = Standard Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor field contains Compaq Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Profile name = Netware Type = Standard Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor field contains Compaq Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Profile name = HP Type = Standard Mode 0 = Volume Set Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor field contains Compaq Mode 11 = No Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write CLI> show globals Global Parameters: System Name: SGM054201C Rebuild Priority: low Expand Priority: high Total Cache: 256MB 50% Read Cache: 128MB 50% Write Cache: 128MB Temperature: EMU: 29 Celsius, 84 Fahrenheit PS1: 39 Celsius, 102 Fahrenheit PS2: 40 Celsius, 104 Fahrenheit FIBRE BAY: 40 Celsius, 104 Fahrenheit CLI> show acl ACL is enabled: Connection WWPN Units Titan-sw2-p1 210000E0-8B841A41 0 Titan-sw1-p1 210000E0-8B8526AA 0 Rhea-sw2-p2 210000E0-8B84DE40 1 Rhea-sw1-p2 210000E0-8B85B3B2 1 Inaccessible Units: None CLI> show connections Connection Name: Titan-sw2-p1 Host WWNN = 210000E0-8B841A41 Host WWPN = 210000E0-8B841A41 Profile Name = Linux Unit Offset = 0 Connection Name: Rhea-sw2-p2 Host WWNN = 210000E0-8B84DE40 Host WWPN = 210000E0-8B84DE40 Profile Name = Linux Unit Offset = 0 s Connection Name: Titan-sw1-p1 Host WWNN = 210000E0-8B8526AA Host WWPN = 210000E0-8B8526AA Profile Name = Linux Unit Offset = 0 s h box,bay bus,ID Size Speed Units Disk101 1,01 0,00 146.8 GB 160 MB/s 0 Disk102 1,02 0,01 146.8 GB 160 MB/s 0 Disk103 1,03 0,02 146.8 GB 160 MB/s 0 Disk104 1,04 0,03 146.8 GB 160 MB/s 0 Disk105 1,05 0,04 146.8 GB 160 MB/s 0 Disk106 1,06 0,05 146.8 GB 160 MB/s 1 Disk107 1,07 0,08 146.8 GB 160 MB/s 1 Disk108 1,08 1,00 146.8 GB 160 MB/s 0 Disk109 1,09 1,01 146.8 GB 160 MB/s 0 Disk110 1,10 1,02 146.8 GB 160 MB/s 0 Disk111 1,11 1,03 146.8 GB 160 MB/s 0 Disk112 1,12 1,04 146.8 GB 160 MB/s 0 Disk113 1,13 1,05 146.8 GB 160 MB/s 1 Disk114 1,14 1,08 146.8 GB 160 MB/s 1 Disk201 2,01 2,00 146.8 GB 160 MB/s none Disk202 2,02 2,01 146.8 GB 160 MB/s none Disk203 2,03 2,02 146.8 GB 160 MB/s none Disk204 2,04 2,03 146.8 GB 160 MB/s none Disk205 2,05 2,04 146.8 GB 160 MB/s none Disk206 2,06 2,05 146.8 GB 160 MB/s none Disk207 2,07 2,08 146.8 GB 160 MB/s none Disk208 2,08 2,09 146.8 GB 160 MB/s none Disk209 2,09 2,10 146.8 GB 160 MB/s none Disk210 2,10 2,11 146.8 GB 160 MB/s none Disk211 2,11 2,12 146.8 GB 160 MB/s none Disk212 2,12 2,13 146.8 GB 160 MB/s none Disk213 2,13 2,14 146.8 GB 160 MB/s none Disk214 2,14 2,15 146.8 GB 160 MB/s none Notes: The speed is the currently negotiated speed to the disk. This may be less than the maximum speed supported by the device due to bus faults, loss of signal integrity, etc. Unit 0: In PDLA mode, Unit 0 is Lun 1; In VSA mode, Unit 0 is Lun 0. Unit Identifier : Device Identifier : 600805F3-001847A0-A3030FD4-894F0000 Cache Status : Enabled Max Boot Partition: Disabled Volume Status : VOLUME OK Parity Init Status: Complete 10 Data Disk(s) used by lun 0: Disk101: Box 1, Bay 01, (SCSI bus 0, SCSI id 0) Disk102: Box 1, Bay 02, (SCSI bus 0, SCSI id 1) Disk103: Box 1, Bay 03, (SCSI bus 0, SCSI id 2) Disk104: Box 1, Bay 04, (SCSI bus 0, SCSI id 3) Disk105: Box 1, Bay 05, (SCSI bus 0, SCSI id 4) Disk108: Box 1, Bay 08, (SCSI bus 1, SCSI id 0) Disk109: Box 1, Bay 09, (SCSI bus 1, SCSI id 1) Disk110: Box 1, Bay 10, (SCSI bus 1, SCSI id 2) Disk111: Box 1, Bay 11, (SCSI bus 1, SCSI id 3) Disk112: Box 1, Bay 12, (SCSI bus 1, SCSI id 4) Spare Disk(s) used by lun 0: No spare drive is designated. Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (Raid 5) stripe_size=16kB Logical Volume Capacity : 1,260,124MB Unit 1: In PDLA mode, Unit 1 is Lun 2; In VSA mode, Unit 1 is Lun 1. Unit Identifier : Device Identifier : 600805F3-001847A0-A2E332C8-6E3E0001 Cache Status : Enabled Max Boot Partition: Disabled Volume Status : VOLUME OK Parity Init Status: Complete 4 Data Disk(s) used by lun 1: Disk106: Box 1, Bay 06, (SCSI bus 0, SCSI id 5) Disk107: Box 1, Bay 07, (SCSI bus 0, SCSI id 8) Disk113: Box 1, Bay 13, (SCSI bus 1, SCSI id 5) Disk114: Box 1, Bay 14, (SCSI bus 1, SCSI id 8) Spare Disk(s) used by lun 1: No spare drive is designated. Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (Raid 5) stripe_size=16kB Logical Volume Capacity : 420,041MB Connection Name: Rhea-sw1-p2 Host WWNN = 210000E0-8B85B3B2 Host WWPN = 210000E0-8B85B3B2 Profile Name = Linux Unit Offset = 0 show this_controller Con CLI> show other_controller CLI> Controller: MSA1000(c) Compaq P56350HX3SJ049 Software 4.48 Build 342 Hardware 7 Controller Identifier: NODE_ID = 500805F3-001847A0 SCSI_VERSION = SCSI-3 Supported Redundancy Mode: Active/Standby Current Redundancy Mode: Active/Standby Current Role: Standby Device Port SCSI address 7 Terminal speed for the CLI is set to 19200. Host Port_1: REPORTED PORT_ID 500805F3-001847A9 PORT_1_TOPOLOGY = F_Port Cache: 128 megabyte read cache 128 megabyte write cache Version 2 Cache is GOOD, and Cache is enabled. No unflushed data in cache Battery: Module #1 is fully charged and turned off. Controller Up Time: 0 Days 03 Hours 00 Minutes 52 Seconds