CLI-1> show version -all MSA1000 Firmware Revision: 5.20b1500 (M119LYPN7R) Build Time: 2007-01-24 16:03:28 MSA1000 Hardware Revision: 7 [AutoRev: 0x010000] Fibre Module AutoRev: 0x010000 Box 1a PROLIANT 6L7I DB Rev: 2.28 (M119LYPN7R) Box 1b PROLIANT 6L7I DT Rev: 2.28 (M119LYPN7R) Disk Drives: B T L BOX BAY GB Model Rev. Serial No. 0 0 0 1 1 146.8 COMPAQ BF1468A4CC HPB5 3KN2RS8N00009719T649 0 1 0 1 2 146.8 COMPAQ BF1468A4CC HPB5 3KN2T29X00009719UY2C 0 2 0 1 3 146.8 COMPAQ BF1468A4CC HPB5 3KN2T38H00009719S3M2 0 3 0 1 4 146.8 COMPAQ BF1468A4CC HPB5 3KN2T8HJ00009719SKV7 0 4 0 1 5 146.8 COMPAQ BF1468A4CC HPB5 3KN2TCQB00009719SK9K 0 5 0 1 6 146.8 COMPAQ BF1468A4CC HPB5 3KN2SRX500009719TKTW 0 8 0 1 7 146.8 COMPAQ BF1468A4CC HPB5 3KN2SJ4Y00009716TPQD 1 0 0 1 8 146.8 COMPAQ BF1468A4CC HPB5 3KN2T50300009719T5DD 1 1 0 1 9 146.8 COMPAQ BF1468A4CC HPB5 3KN2TD9S00009719T5DX 1 2 0 1 10 146.8 COMPAQ BF1468A4CC HPB5 3KN2S3N800009719SHTE 1 3 0 1 11 146.8 COMPAQ BF1468A4CC HPB5 3KN2SRZC00009719T62T 1 4 0 1 12 146.8 COMPAQ BF1468A4CC HPB5 3KN2VBJ100009719TJXN 1 5 0 1 13 146.8 COMPAQ BF1468A4CC HPB5 3KN2T8CD00009719S4BJ 1 8 0 1 14 146.8 COMPAQ BF1468A4CC HPB5 3KN2SSCT00009719T6BY CLI-1> show profile Profile name = Default (Default) Mode value = (00004005) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Ignore Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Windows Type = Standard Mode value = (00004005) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Ignore Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Windows (degraded performance) Type = Standard Mode value = (00005005) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = OpenVMS Type = Standard Mode value = (00005073) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = VMS shadow style bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Tru64 Type = Standard Mode value = (00005163) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Linux Type = Standard Mode value = (000050a7) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Solaris Type = Standard Mode value = (000050a7) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Netware Type = Standard Mode value = (000050a7) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = HP Type = Standard Mode value = (000058a6) Mode 0 = Volume Set Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = No Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = XP Storage Array Type = Standard Mode value = (00005163) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode CLI-1> show globals Global Parameters: System Name: IDW-STORE Rebuild Priority: high Expand Priority: high Surface Delay: 3.0 seconds Total Cache: 256MB 50% Read Cache: 128MB 50% Write Cache: 128MB Temperature: No temperature sensor support. CLI-1> show acl ACL is enabled: Connection WWPN Units IDWSVR_IDWSTORE 50060B00-0011CBBA 0 Inaccessible Units: None CLI-1> show connections Connection Name: IDWSVR_IDWSTORE Host WWNN = 50060B00-0011CBBB Host WWPN = 50060B00-0011CBBA Profile Name = Default Unit Offset = 0 Controller 1 Port 1 Status = Offline Controller 2 Port 1 Status = Offline CLI-1> show disks Disk List: (box,bay) (B:T:L) Size Speed Units Enclosure 1: SCSI (0:06:00) PROLIANT 6L7I DB2.28 Disk101 (1,01) (0:00:00) 146.8GB 160 MB/s 0 Disk102 (1,02) (0:01:00) 146.8GB 160 MB/s 0 Disk103 (1,03) (0:02:00) 146.8GB 160 MB/s 0 Disk104 (1,04) (0:03:00) 146.8GB 160 MB/s 0 Disk105 (1,05) (0:04:00) 146.8GB 160 MB/s 0 Disk106 (1,06) (0:05:00) 146.8GB 160 MB/s 0 Disk107 (1,07) (0:08:00) 146.8GB 160 MB/s 0 Disk108 (1,08) (1:00:00) 146.8GB 160 MB/s 0 Disk109 (1,09) (1:01:00) 146.8GB 160 MB/s 0 Disk110 (1,10) (1:02:00) 146.8GB 160 MB/s 0 Disk111 (1,11) (1:03:00) 146.8GB 160 MB/s 0 Disk112 (1,12) (1:04:00) 146.8GB 160 MB/s 0 Disk113 (1,13) (1:05:00) 146.8GB 160 MB/s 0 Disk114 (1,14) (1:08:00) 146.8GB 160 MB/s 0 Notes: The speed is the currently negotiated speed to the disk. This may be less than the maximum speed supported by the device due to bus faults, loss of signal integrity, etc. CLI-1> show box No external storage boxes are attached. CLI-1> show units Unit 0: In PDLA mode, Unit 0 is Lun 1; In VSA mode, Unit 0 is Lun 0. Unit Identifier : Device Identifier : 60060B00-00843800-98EB3F55-E0920003 Preferred Path : Controller 1 (this controller) Cache Status : Enabled Max Boot Partition: Enabled Volume Status : VOLUME OK Mirror Init Status: Complete 14 Data Disk(s) used by lun 0: Disk101: Box 1, Bay 01, (B:T:L 0:00:00) Disk102: Box 1, Bay 02, (B:T:L 0:01:00) Disk103: Box 1, Bay 03, (B:T:L 0:02:00) Disk104: Box 1, Bay 04, (B:T:L 0:03:00) Disk105: Box 1, Bay 05, (B:T:L 0:04:00) Disk106: Box 1, Bay 06, (B:T:L 0:05:00) Disk107: Box 1, Bay 07, (B:T:L 0:08:00) Disk108: Box 1, Bay 08, (B:T:L 1:00:00) Disk109: Box 1, Bay 09, (B:T:L 1:01:00) Disk110: Box 1, Bay 10, (B:T:L 1:02:00) Disk111: Box 1, Bay 11, (B:T:L 1:03:00) Disk112: Box 1, Bay 12, (B:T:L 1:04:00) Disk113: Box 1, Bay 13, (B:T:L 1:05:00) Disk114: Box 1, Bay 14, (B:T:L 1:08:00) Spare Disk(s) used by lun 0: No spare drive is designated. Logical Volume Raid Level: MIRROR FAULT TOLERANCE (RAID 1) stripe_size=128kB Logical Volume Capacity : 980,090MB CLI-1> show this_controller Controller 1 (right controller): MSA1000(c) Hewlett-Packard P56350GX3QH026 Version 5.20 Build 1500 Hardware 7 Build Time: 2007-01-24 16:03:28 Integrated Enclosure. Controller Identifier: NODE_ID = 50060B00-00843800 SCSI_VERSION = SCSI-3 Supported Redundancy Mode: Active/Standby Asym-Active/Active Current Redundancy Mode: Active/Standby (emulated) Current Role: Active Device Port SCSI address 6 Terminal speed for the CLI is set to 19200. Host Port_1: REPORTED PORT_ID 50060B00-00843801 PORT_1_TOPOLOGY = Link Down Cache: 128 megabyte read cache 128 megabyte write cache Version 2 Cache is GOOD, and Cache is enabled. No unflushed data in cache Batteries are disabled Module #1 is fully charged and turned off. Controller Up Time: 0 Days 01 Hours 02 Minutes 44 Seconds Health: Surface Scan: Complete. Rebuild Status: Complete. Expansion: Complete. CLI-1> show other_controller Controller 2 (left controller): MSA1000(c) Hewlett-Packard P56350DX3PU0B9 Version 5.20 Build 1500 Hardware 7 Build Time: 2007-01-24 16:03:28 Integrated Enclosure. Controller Identifier: NODE_ID = 50060B00-00843800 SCSI_VERSION = SCSI-3 Supported Redundancy Mode: Active/Standby Asym-Active/Active Current Redundancy Mode: Active/Standby (emulated) Current Role: Standby Device Port SCSI address 7 Terminal speed for the CLI is set to 19200. Host Port_1: REPORTED PORT_ID 50060B00-00843809 PORT_1_TOPOLOGY = Arbitrated Loop Cache: 128 megabyte read cache 128 megabyte write cache Version 2 Cache is GOOD, and Cache is enabled. No unflushed data in cache Batteries are disabled Module #1 is fully charged and turned off. Controller Up Time: 0 Days 01 Hours 02 Minutes 48 Seconds Health: Surface Scan: Complete. Rebuild Status: Complete. Expansion: Complete. CLI-1> show eventlog No Events Logged. CLI-1> show preferred_path Controller 1 (this_controller) is the current optimal path for these units: 0 Controller 2 (other_controller) is the current optimal path for these units: None Implicit (automatic load-based) LUN ownership changes are currently ENABLED. CLI-1> show auto_path_change Implicit (automatic load-based) LUN ownership changes are currently ENABLED. Implicit LUN ownership change preferences are as follows: Minimum % of proxied requests to trigger implicit path change..: 75% Minimum number of requests to LUN before path change enabled...: 65536 Minimum time to wait before changing ownership after power-up..: 30 mi