CLI-1> show show tech_support CLI-1> show version -all MSA1500 Firmware Revision: 5.20b1500 (SGA074102X) Build Time: 2007-01-24 16:03:28 MSA1500 Hardware Revision: a [AutoRev: 0x030000] Fibre Module AutoRev: 0x020000 SCSI I/O Module Bus 0 Revision: 2.02 SCSI I/O Module Bus 1 Revision: <> SCSI I/O Module Bus 2 Revision: <> SCSI I/O Module Bus 3 Revision: <> Fan Control Module A Revision: 2.38 Fan Control Module B Revision: 2.38 Box 1 PROLIANT 4LEE Rev: CP20 (MEELLMPX9M) Disk Drives: B T L BOX BAY GB Model Rev. Serial No. 0 0 0 1 1 300.0 COMPAQ BF30084971 HPB5 0 1 0 1 2 300.0 COMPAQ BF30084971 HPB5 0 2 0 1 3 300.0 COMPAQ BF30084971 HPB5 0 3 0 1 4 300.0 COMPAQ BF30084971 HPB5 0 4 0 1 5 300.0 COMPAQ BF30084971 HPB5 0 5 0 1 6 300.0 COMPAQ BF30084971 HPB5 0 8 0 1 7 300.0 COMPAQ BF30084971 HPB5 0 9 0 1 8 300.0 COMPAQ BF30084971 HPB5 CLI-1> show profile Profile name = Default (Default) Mode value = (00004005) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Ignore Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Windows Type = Standard Mode value = (00004005) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Ignore Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Windows (degraded performance) Type = Standard Mode value = (00005005) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Legacy Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout selected initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = OpenVMS Type = Standard Mode value = (00005073) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = VMS shadow style bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Tru64 Type = Standard Mode value = (00005163) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Linux Type = Standard Mode value = (000050a7) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Solaris Type = Standard Mode value = (000050a7) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = Netware Type = Standard Mode value = (000050a7) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = HP Type = Standard Mode value = (000058a6) Mode 0 = Volume Set Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as available on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events not reported through Unit Attention Mode 7 = Send FCP response info with SCSI status Mode 8 = Do not send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = No Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode Profile name = XP Storage Array Type = Standard Mode value = (00005163) Mode 0 = Peripheral Device LUN Addressing Mode 1 = Asymmetric Failover Mode 2 = Logical volumes connect as unavailable on Backup Controller Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode) Mode 4 = Normal bad block handling Mode 5 = Logout all initiators on TPRLO Mode 6 = Fault management events reported through Unit Attention Mode 7 = Do not send FCP response info with SCSI status Mode 8 = Send Unit Attention on failover Mode 9 = SCSI inquiry revision field contains the actual version Mode 10 = SCSI inquiry vendor ID='Compaq' Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout Mode 12 = Enforce Force Unit Access on Write Mode 13 = Ignore Target Port on Reservation Mode 14 = Active/Standby Operating Mode CLI-1> show globals Global Parameters: System Name: Rebuild Priority: medium Expand Priority: medium Surface Delay: 3.0 seconds Total Cache: 512MB 50% Read Cache: 256MB 50% Write Cache: 256MB Temperature: EMU: 23 Celsius, 73 Fahrenheit PS1: 23 Celsius, 73 Fahrenheit PS2: 25 Celsius, 77 Fahrenheit CLI-1> show acl ACL is enabled: Connection WWPN Units con1 50014380-00C2AA76 0, 1 Inaccessible Units: None CLI-1> show connections Connection Name: con1 Host WWNN = 50014380-00C2AA77 Host WWPN = 50014380-00C2AA76 Profile Name = Linux Unit Offset = 0 Controller 1 Port 1 Status = Online CLI-1> show disks Disk List: (box,bay) (B:T:L) Size Speed Units Enclosure 1: SCSI (0:06:00) PROLIANT 4LEE CP20 Disk101 (1,01) (0:00:00) 300.0GB 160 MB/s 0 Disk102 (1,02) (0:01:00) 300.0GB 160 MB/s 0 Disk103 (1,03) (0:02:00) 300.0GB 160 MB/s 0 Disk104 (1,04) (0:03:00) 300.0GB 160 MB/s 0 Disk105 (1,05) (0:04:00) 300.0GB 160 MB/s 1 Disk106 (1,06) (0:05:00) 300.0GB 160 MB/s 1 Disk107 (1,07) (0:08:00) 300.0GB 160 MB/s 1 Disk108 (1,08) (0:09:00) 300.0GB 160 MB/s 1 Notes: The speed is the currently negotiated speed to the disk. This may be less than the maximum speed supported by the device due to bus faults, loss of signal integrity, etc. CLI-1> show box Box #1: SCSI enclosure at bus 0 channel 0 target 6 Firmware ID string: PROLIANT 4LEE Firmware revision: CP20 Serial number: MEELLMPX9M Environmental Status: No alert conditions reported CLI-1> show units Unit 0: In PDLA mode, Unit 0 is Lun 1; In VSA mode, Unit 0 is Lun 0. Unit Identifier : Device Identifier : 600508B3-009555E0-3130563E-FD2D0000 Preferred Path : Controller 1 (this controller) Cache Status : Enabled Max Boot Partition: Enabled Volume Status : VOLUME OK Mirror Init Status: Complete 4 Data Disk(s) used by lun 0: Disk101: Box 1, Bay 01, (B:T:L 0:00:00) Disk102: Box 1, Bay 02, (B:T:L 0:01:00) Disk103: Box 1, Bay 03, (B:T:L 0:02:00) Disk104: Box 1, Bay 04, (B:T:L 0:03:00) Spare Disk(s) used by lun 0: No spare drive is designated. Logical Volume Raid Level: MIRROR FAULT TOLERANCE (RAID 1) stripe_size=128kB Logical Volume Capacity : 572,197MB Unit 1: In PDLA mode, Unit 1 is Lun 2; In VSA mode, Unit 1 is Lun 1. Unit Identifier : Device Identifier : 600508B3-009555E0-9258DE8D-8E0A0001 Preferred Path : Controller 1 (this controller) Cache Status : Enabled Max Boot Partition: Enabled Volume Status : VOLUME OK Mirror Init Status: Complete 4 Data Disk(s) used by lun 1: Disk105: Box 1, Bay 05, (B:T:L 0:04:00) Disk106: Box 1, Bay 06, (B:T:L 0:05:00) Disk107: Box 1, Bay 07, (B:T:L 0:08:00) Disk108: Box 1, Bay 08, (B:T:L 0:09:00) Spare Disk(s) used by lun 1: No spare drive is designated. Logical Volume Raid Level: MIRROR FAULT TOLERANCE (RAID 1) stripe_size=128kB Logical Volume Capacity : 572,197MB CLI-1> show this_controller Controller 1 (right controller): MSA1500(c) Hewlett-Packard PB984ABX3V7084 Version 5.20 Build 1500 Hardware A Build Time: 2007-01-24 16:03:28 Component Enclosure. Controller Identifier: NODE_ID = 500508B3-009555E0 SCSI_VERSION = SCSI-3 Supported Redundancy Mode: Active/Standby Asym-Active/Active Current Redundancy Mode: Not Redundant (No Failure) Device Port SCSI address 6 Terminal speed for the CLI is set to 19200. Host Port_1: REPORTED PORT_ID 500508B3-009555E1 PORT_1_TOPOLOGY = Arbitrated Loop Cache: 256 megabyte read cache 256 megabyte write cache Version 2 Cache is GOOD, and Cache is enabled. No unflushed data in cache Batteries are disabled Module #1 is fully charged and turned off. Module #2 is fully charged and turned off. Controller Up Time: 13 Days 18 Hours 08 Minutes 15 Seconds Health: Surface Scan: Complete. Rebuild Status: Complete. Expansion: Complete. CLI-1> show other_controller Other controller is not present or fully started. CLI-1> show eventlog TIME CLASS SUB DETL MESSAGE 0d 00:00:07.9 0002 0002 0000 Fan failure: 0 0d 00:00:09.5 0001 0004 0000 Controller removed: 0 0d 00:26:10.6 0002 0002 0002 Fan is now operational: 0 0d 00:26:10.6 0001 0001 0001 Power supply inserted: 0 0d 00:28:50.8 0001 0000 0001 Hot-plug drive inserted: Box: 1, Bay: 1 0d 00:28:50.8 0001 0000 0001 Hot-plug drive inserted: Box: 1, Bay: 2 0d 00:28:50.9 0001 0000 0001 Hot-plug drive inserted: Box: 1, Bay: 3 0d 00:28:50.9 0001 0000 0001 Hot-plug drive inserted: Box: 1, Bay: 4 0d 00:28:51.0 0001 0000 0001 Hot-plug drive inserted: Box: 1, Bay: 5 0d 00:28:51.0 0001 0000 0001 Hot-plug drive inserted: Box: 1, Bay: 6 0d 00:28:51.1 0001 0000 0001 Hot-plug drive inserted: Box: 1, Bay: 7 0d 00:28:51.1 0001 0000 0001 Hot-plug drive inserted: Box: 1, Bay: 8 0d 00:29:53.6 0005 0000 0000 State change on volume: 0 0d 00:29:54.3 0002 0004 0001 Cache enabled. 0d 00:30:00.0 0005 0000 0000 State change on volume: 1 0d 00:58:10.1 0005 0002 0000 Parity/consistency initialization complete, volu 00d 01:18:00.5 0005 0002 0000 Parity/consistency initialization complete, volu 1 CLI-1> show preferred_path Controller 1 (this_controller) is the current optimal path for these units: 0,1 Implicit (automatic load-based) LUN ownership changes are currently ENABLED. CLI-1> show auto_path_change Implicit (automatic load-based) LUN ownership changes are currently ENABLED. Implicit LUN ownership change preferences are as follows: Minimum % of proxied requests to trigger implicit path change..: 75% Minimum number of requests to LUN before path change enabled...: 65536 Minimum time to wait before changing ownership after power-up..: 30 minutes Minimum time between ownership changes for LUN.................: 30 minutes CLI-1>