****************************************************************************** **** **** **** S A U T I L S u p p o r t U t i l i t y **** **** **** **** for the HP SmartArray RAID Controller Family **** **** **** **** version A.02.13 **** **** **** **** (C) Copyright 2003-2007 Hewlett-Packard Development Company, L.P. **** ****************************************************************************** ---- DRIVER INFORMATION ------------------------------------------------------ Driver State........................ READY ---- CONTROLLER INFORMATION -------------------------------------------------- Controller Product Number........... A9890A Controller Product Name............. HP PCI-X SmartArray 6402 Hardware Path....................... 0/2/1/0/4/0 Serial Number....................... P57820G9SQ107T Device File......................... /dev/ciss7 Hardware Revision................... 'B' Boot Block Revision................. 6.30 Firmware Revision (running)......... 2.84 Firmware Revision (in ROM).......... 2.84 Firmware Revision (inactive)........ 2.58 # of Logical Drives................. 1 # of Physical Disks Configured...... 14 # of Physical Disks Detected........ 14 Logical Drive Rebuild Priority...... 118 (high) Array Capacity Expansion Priority... 0 (low) Auto-Fail Missing Disks at Boot..... enabled SCSI Transfer Detection Mode........ Auto Detect Controller Path Selection Method.... default ---- ARRAY ACCELERATOR (CACHE) INFORMATION ----------------------------------- Array Accelerator Board Present?.... yes Cache Configuration Status.......... write cache temporarily disabled (code=1) Cache Ratio......................... 50% Read / 50% Write Total Cache Size (MB)............... 128 Read Cache........................ 064 Write Cache....................... 064 Transfer Buffer................... 000 Battery Pack Count.................. 2 Battery Status (pack #1)............ FAILED Battery Status (pack #2)............ ok ---- LOGICAL DRIVE SUMMARY --------------------------------------------------- # RAID Size Status 0 1+0 2002684 MB RECOVERING ---- SCSI DEVICE SUMMARY ----------------------------------------------------- Location Ch ID Type Capacity Status external 1 0 DISK 300.0 GB OK external 1 1 DISK 300.0 GB OK external 1 2 DISK 300.0 GB OK external 1 3 DISK 300.0 GB OK external 1 4 DISK 300.0 GB OK external 1 5 DISK 300.0 GB OK external 1 7 PROCESSOR external 1 8 DISK 300.0 GB OK external 2 0 DISK 300.0 GB OK external 2 1 DISK 300.0 GB OK external 2 2 DISK 300.0 GB OK external 2 3 DISK 300.0 GB OK external 2 4 DISK 300.0 GB OK external 2 5 DISK 300.0 GB OK external 2 8 DISK 300.0 GB OK external 2 15 PROCESSOR ---- SCSI BUS SUMMARY -------------------------------------------------------- External Internal Ch LVD_Mode Connector Connector 1 YES YES - 2 YES YES - ---- LOGICAL DRIVE 0 --------------------------------------------------------- Logical Drive Device File........... c7t0d0 Fault Tolerance Mode................ RAID 1+0 (Disk Mirroring) Logical Drive Size.................. 2002684 MB Logical Drive Status................ RECOVERING # of Participating Physical Disks... 14 Participating Physical Disk(s)...... Ch:ID 1: 0 1: 1 1: 2 1: 3 1: 4 1: 5 1: 8 2: 0 2: 1 2: 2 2: 3 2: 4 2: 5 2: 8 Participating Spare Disk(s)......... Ch:ID none Stripe Size......................... 128 KB Logical Drive Cache Status.......... write cache temporarily disabled (code=1) Configuration Signature............. 0xA03A77B8 Media Exchange Detected?............ no ---- SCSI DEVICE 1:0 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 0 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR12XK3000076130PPB Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. MISSING IN SAVE RIS Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:1 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 1 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30087B53 Device Serial Number............................. D80ACV0K Device Firmware Version.......................... HPB7 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:2 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 2 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR0YVEE00007608W87X Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. TIMEOUT Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:3 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 3 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR0Y1LG00007609MKJH Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:4 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 4 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD3008A4C6 Device Serial Number............................. 3KR1SS7Z00007631H11V Device Firmware Version.......................... HPB4 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. DEFERRED WRITE ERROR Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... yes Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:5 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 5 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30087B53 Device Serial Number............................. D80B2XAK Device Firmware Version.......................... HPB7 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 1:7 [PROCESSOR] --------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 7 Device Type...................................... PROCESSOR Device Vendor ID................................. COMPAQ Device Product ID................................ PROLIANT 4L7E*DT SCSI Transfer Rate (maximum)..................... Ultra-320 ---- SCSI DEVICE 1:8 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 1 SCSI ID.......................................... 8 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR0WLWP00007607CD6Q Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:0 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 0 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR12AR400007612NB96 Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:1 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 1 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR0WZ0S00007608R8LC Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:2 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 2 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR0ZBZF00007613NRWJ Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. MISSING IN SAVE RIS Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:3 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 3 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR0ZBZ900007608CLQG Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:4 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 4 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR0X13D00007608S4Z2 Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:5 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 5 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR0Z9PG00007609A57J Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:8 [DISK] -------------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 8 Device Type...................................... DISK Disk Capacity.................................... 300.0 GB Device Status.................................... OK Device Vendor ID................................. COMPAQ Device Product ID................................ BD30088279 Device Serial Number............................. 3KR0XP3T00007608J7HQ Device Firmware Version.......................... HPB2 SCSI Transfer Rate (actual)...................... Ultra-320 Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB) Block Size (bytes/sector)........................ 512 bytes M&P Data Stamped?................................ yes Last Failure Reason.............................. none Physical Disk Flags: Disk present and operational................... yes Non-disk device detected....................... no Wide SCSI transfer enabled..................... yes Synchronous (Fast/Ultra) transfer enabled...... yes Narrow disk tray detected...................... no Wide transfer failed, reverted to narrow....... no Ultra SCSI transfer enabled.................... yes Ultra-2 SCSI transfer enabled.................. yes S.M.A.R.T. supported........................... yes S.M.A.R.T. errors (in factory M&P data)........ no S.M.A.R.T. enabled............................. yes S.M.A.R.T. errors (in powerup M&P data)........ no Attached to external channel................... yes Configured in a logical drive.................. yes Configured as a spare disk..................... no Disk write cache enabled at spin up............ no Running in DT clocking mode.................... yes Supports DT clocking mode only................. no Supports DT and ST clocking modes.............. yes Running in U320 mode........................... yes Packetized SCSI supported...................... yes Supports redundant controller operation........ yes Disk write cache enabled in current page....... no Disk write cache disabled in default page...... yes QAS capable (U320 only)........................ yes Currently running QAS (U320 only).............. no ---- SCSI DEVICE 2:15 [PROCESSOR] -------------------------------------------- Connector Location............................... external Channel Number................................... 2 SCSI ID.......................................... 15 Device Type...................................... PROCESSOR Device Vendor ID................................. COMPAQ Device Product ID................................ PROLIANT 4L7E*DB SCSI Transfer Rate (maximum)..................... Ultra-320 ---- DIAGRAM OF EXTERNAL CONNECTORS ON BRACKET ------------------------------- ========---======== | | | U320 <--- LOOK FOR THIS LOGO | / \ | | <- | | \ / | | | | * * | | * * * * | (Ch A1)---> * * * * <--- (Ch A2) | * * * * | | * * | | | | | | | | | | | | | | | | | | | ~ ~ ~ ~ ~ ****************************************************************************** **** End of SAUTIL Output **** ******************************************************************************