1. System Information System Model : eserver xSeries 346 -[884025M]- Operating System : Windows Server 2003 Service Pack 1 Processor : 2 x unknown System Name : Physical Memory : 2047 MB Tool Version : Version 4.2 System Time : Monday January 15 2007 - 11:02:28 1.1 Device Listing: By Connection Host Bus Adapter 'a320raid SCSI Adapter' at Address '1/0.7.0' Disk 'ADAPTEC RAID 1' at Address '1/0.0.0' Processor 'ADAPTEC HostRAID' at Address '1/0.15.0' Processor 'IBM 40K6480a S320 0' at Address '1/0.8.0' Host Bus Adapter 'adpu320 SCSI Adapter' at Address '2/0.7.0' Tape 'HP Ultrium 3-SCSI' at Address '2/0.4.0' Media_Changer 'HP MSL G3 Series' at Address '2/0.4.1' Host Bus Adapter 'elxstor SCSI Adapter' at Address '3/0.255.0' Disk 'HITACHI DF600F' at Address '3/0.0.0' Host Bus Adapter 'elxstor SCSI Adapter' at Address '3/1.255.0' Host Bus Adapter 'elxstor SCSI Adapter' at Address '3/2.255.0' Host Bus Adapter 'elxstor SCSI Adapter' at Address '3/3.255.0' 1.2 Device Listing: By Product Libraries Media_Changer 'HP MSL G3 Series' at Address '2/0.4.1' Drive 1 'HP Ultrium 3-SCSI' at Address '2/0.4.0' Drives Other Devices Disk 'ADAPTEC RAID 1' at Address '1/0.0.0' Processor 'ADAPTEC HostRAID' at Address '1/0.15.0' Processor 'IBM 40K6480a S320 0' at Address '1/0.8.0' Disk 'HITACHI DF600F' at Address '3/0.0.0' 2. Detailed Device Information 2.1 Media Changer at address (2/0.4.1) Model Name : MSL G3 Series Library Vendor ID : HP Product ID : MSL G3 Series Product Variant ID : MSL 2024 Firmware Revision : 2.40 Controller Serial # : DEC06412JC SCSI Test Unit Ready returns status good. Library Components Number of Drives : 1 Drive 1, element number 1 (0x0001) Product ID : Ultrium 3-SCSI Serial Number: HU10639H6R Firmware Rev : G53W Path : 2/0.4.0 Number of Storage Slots : 24 First element number: 1001 (0x03E9) Last element number : 1024 (0x0400) Number of Mail Slots : 0 Device Analysis Firmware rev '2.40' is out-of-date as of Fri Oct 27 19:00:00 2006; update to rev '3.00'. Device Analysis completed, and warnings have been reported. Cartridge Inventory 0 Full Drives 1 Empty Drive Drive 1, element number 1 (0x0001) 5 Full Slots Slot 15, element number 1015 (0x03F7), barcode TB2076LT Slot 16, element number 1016 (0x03F8), barcode TB2064LT Slot 19, element number 1019 (0x03FB), barcode TB2060LT Slot 20, element number 1020 (0x03FC), barcode TB2062LT Slot 24, element number 1024 (0x0400), barcode TB2063LT 19 Empty Slots Slot 1, element number 1001 (0x03E9) Slot 2, element number 1002 (0x03EA) Slot 3, element number 1003 (0x03EB) Slot 4, element number 1004 (0x03EC) Slot 5, element number 1005 (0x03ED) Slot 6, element number 1006 (0x03EE) Slot 7, element number 1007 (0x03EF) Slot 8, element number 1008 (0x03F0) Slot 9, element number 1009 (0x03F1) Slot 10, element number 1010 (0x03F2) Slot 11, element number 1011 (0x03F3) Slot 12, element number 1012 (0x03F4) Slot 13, element number 1013 (0x03F5) Slot 14, element number 1014 (0x03F6) Slot 17, element number 1017 (0x03F9) Slot 18, element number 1018 (0x03FA) Slot 21, element number 1021 (0x03FD) Slot 22, element number 1022 (0x03FE) Slot 23, element number 1023 (0x03FF) HP Event Logs Log Timestamp: 18:27:06 - 2000/01/05 Log entries are not time zone corrected and may be local time or UTC time Events in the last 24 hours 18:20:06 - 2000/01/05 Crit:0x008A HE: invalid rotation range Global error code: 159 (0x9F) Rotation range out of specification Module error code: 8 (0x08) Robotic:Error during rotation initialization, get range failed Current command: 0 (0x00) 18:16:15 - 2000/01/05 Crit:0x008A HE: invalid rotation range Global error code: 159 (0x9F) Rotation range out of specification Module error code: 8 (0x08) Robotic:Error during rotation initialization, get range failed Current command: 50 (0x32) 18:13:51 - 2000/01/05 Crit:0x008A HE: invalid rotation range Global error code: 159 (0x9F) Rotation range out of specification Module error code: 8 (0x08) Robotic:Error during rotation initialization, get range failed Current command: 77 (0x4D) 18:13:07 - 2000/01/05 Crit:0x008A HE: invalid rotation range Global error code: 159 (0x9F) Rotation range out of specification Module error code: 8 (0x08) Robotic:Error during rotation initialization, get range failed Current command: 18 (0x12) 18:12:36 - 2000/01/05 Crit:0x008A HE: invalid rotation range Global error code: 159 (0x9F) Rotation range out of specification Module error code: 8 (0x08) Robotic:Error during rotation initialization, get range failed Current command: 0 (0x00) 18:11:47 - 2000/01/05 Crit:0x008A HE: invalid rotation range Global error code: 159 (0x9F) Rotation range out of specification Module error code: 8 (0x08) Robotic:Error during rotation initialization, get range failed Current command: 50 (0x32) 18:11:16 - 2000/01/05 Crit:0x008A HE: invalid rotation range Global error code: 159 (0x9F) Rotation range out of specification Module error code: 8 (0x08) Robotic:Error during rotation initialization, get range failed Current command: 50 (0x32) 18:10:24 - 2000/01/05 Crit:0x0077 HE: rotation blocked Global error code: 140 (0x8C) Rotation blocked Module error code: 10 (0x0A) Robotic:Error during rotation to far position Current command: 0 (0x00) Events in the last 31 days 00:02:19 - 2000/01/02 Crit:0x0089 HE: invalid elevator range Global error code: 158 (0x9E) Elevator range out of specification Module error code: 9 (0x09) Robotic:Error elevator init Current command: 50 (0x32) 00:00:49 - 2000/01/02 Crit:0x0089 HE: invalid elevator range Global error code: 158 (0x9E) Elevator range out of specification Module error code: 9 (0x09) Robotic:Error elevator init Current command: 0 (0x00) Events older than 31 days HP Library Status and Statistics Log Media Changer Status : Failed Media Changer temperature status : OK Media Changer Load Port status : Closed Total power on time : 04d 20h 05m 46s Power on time since last power on : 00d 00h 07m 30s Powered on since : 23:53:04 - 2007/01/14 UTC (Calculated) Power cycles : 8 Total number of drives : 1 Total number of storage slots : 24 Total number of I/O slots : 0 Total number of transport elements : 1 Total number of modules : 0 Total number of clean carts : 0 Total number of moves : 1170 Total number of move retries : 0 Total number of move failures : 0 Fan 0 status : OK Fan 1 status : OFF/NOT PRESENT Vendor Unique Logs Statistic Counters Robotic Errors 2.2 Tape at address (2/0.4.0) L&TT Device History Core Data Increase the 'Current Detail Level' (at the top of the screen) for further information. For an explanation of the terms used in the report, please check the on-line L&TT user documentation. Drive Identity Drive Product ID : HP Ultrium 3-SCSI Format : LTO-3 (w/r), LTO-2 (w/r), LTO-1 (r) Firmware : G53W/MSL G3/1x8 G2 (Ver 009.593, Date 2006/03/09-13:40) Serial number : HU10639H6R SCSI Drive ID : 4 OBDR : Not supported WORM : Supported Interface Drive Capability : SCSI U320 Drive Health Drive Device Analysis : Passed with Warnings version: V06.11.2006 Firmware rev G53W is out-of-date for Ultrium 3-SCSI as of Mon Jun 26 19:00:00 2006; update to rev G54W. Rule 19: The current SCSI configuration is likely to be limiting the performance of the drive. Please check that your HBA is the correct type for the drive and that the cabling is good. The SCSI configuration referenced is the one for which device analysis was run and/or the support ticket was pulled. If this is not via your backup server then you may not have an issue. Current SCSI transfer rate limited to: 160 MB/sec. Recommended: 320 MB/sec. or better There were 19 rules checked. Device Analysis completed, and warnings have been reported. Write/read (last 4 tapes) : Great margin (average 100%, worst 100%) Head life : Great margin, 99% life remaining Reposition life : Great margin, 99% life remaining Load/unload life : Great margin, 99% life remaining Drive Configuration Drive Data compression : Enabled Current block size : Not available Detect WORM tampering : Enabled Reads after WORM tampering : Not enabled Media removal (software controlled) : Allowed Interface SCSI Drive ID : 4 SCSI Host ID : 7 Negotiated burst data rate : 160 MB/s Drive Environment Current temperature : 33.3 C - Great margin (69%) Maximum temperature since power cycle : 33.3 C - Great margin (69%) Minimum temperature since power cycle : 29.7 C - Great margin (58%) Drive Performance Drive Estimated native data rate (last 4 tapes) : 25.5 MB/s (170 GB written, 172 GB read) Specified max native data rate : 80 MB/sec. Max data rate achieved (internal to drive) : Unknown Average data rate before compression : Unknown Average data rate after compression : Unknown Write compression ratio : Unknown Read compression ratio : Unknown Drive Usage Drive Power on time : 1 days, 8 hours Tape Pulled : 3.1 full volume equivalents Load/unload cycles : 36 (0% of expected life) Duty cycle : 25% Power cycles : 20 Cleans : 0 Firmware upgrades : 1 Native data volume read/written (last 4 tapes) : Wrote 170 GB, read 172 GB Drive History Errors returned to host (no host-reported errors found in the fault logs) Drive assessment test history no assessment test results Device analysis history Drive mechanism: No problems have been identified with the drive mechanism. Drive PCA: No problems have been identified with the drive PCA. Write / Read capability: No write / read problems were identified with the drive. Cartridge problems: No cartridge related problems were identified with the drive. Miscellaneous problems: Rule Number : 19 Rule Description : Performance and configuration check SCSI configuration (ID0) : Failed Data Compression configuration (ID1) : Compression Enabled WWN Check (ID2) : Passed Cleaning Check (ID3) : Cleaning not requested Media removal prevented (ID4) : Allowed Problem was last reported : 00:00:00:00 power-on (days:hours:minutes:seconds) ago Device Analysis Device Time Stamps Temperature Measurements Write Error Rate Log Read Error Rate Log Write Error Counters Read Error Counters Sequential Access Counters Tape Usage Log Tape Capacity Log Performance Log Data Compression Log Fault Log Event Log SCSI Command History SCSI Configuration ACI Command History ACI Configuration ADI Command History Drive Trace Log EEPROMS Mechanical EEPROM PCA EEPROM 2.2 Tape at address (2/0.4.0) L&TT Device History Core Data Increase the 'Current Detail Level' (at the top of the screen) for further information. For an explanation of the terms used in the report, please check the on-line L&TT user documentation. Drive Identity Drive Product ID : HP Ultrium 3-SCSI Format : LTO-3 (w/r), LTO-2 (w/r), LTO-1 (r) Firmware : G53W/MSL G3/1x8 G2 (Ver 009.593, Date 2006/03/09-13:40) Serial number : HU10639H6R SCSI Drive ID : 4 OBDR : Not supported WORM : Supported Interface Drive Capability : SCSI U320 Drive Health Drive Device Analysis : Passed with Warnings version: V06.11.2006 Firmware rev G53W is out-of-date for Ultrium 3-SCSI as of Mon Jun 26 19:00:00 2006; update to rev G54W. Rule 19: The current SCSI configuration is likely to be limiting the performance of the drive. Please check that your HBA is the correct type for the drive and that the cabling is good. The SCSI configuration referenced is the one for which device analysis was run and/or the support ticket was pulled. If this is not via your backup server then you may not have an issue. Current SCSI transfer rate limited to: 160 MB/sec. Recommended: 320 MB/sec. or better There were 19 rules checked. Device Analysis completed, and warnings have been reported. Write/read (last 4 tapes) : Great margin (average 100%, worst 100%) Head life : Great margin, 99% life remaining Reposition life : Great margin, 99% life remaining Load/unload life : Great margin, 99% life remaining Drive Configuration Drive Data compression : Enabled Current block size : Not available Detect WORM tampering : Enabled Reads after WORM tampering : Not enabled Media removal (software controlled) : Allowed Interface SCSI Drive ID : 4 SCSI Host ID : 7 Negotiated burst data rate : 160 MB/s Drive Environment Current temperature : 33.3 C - Great margin (69%) Maximum temperature since power cycle : 33.3 C - Great margin (69%) Minimum temperature since power cycle : 29.7 C - Great margin (58%) Drive Performance Drive Estimated native data rate (last 4 tapes) : 25.5 MB/s (170 GB written, 172 GB read) Specified max native data rate : 80 MB/sec. Max data rate achieved (internal to drive) : Unknown Average data rate before compression : Unknown Average data rate after compression : Unknown Write compression ratio : Unknown Read compression ratio : Unknown Drive Usage Drive Power on time : 1 days, 8 hours Tape Pulled : 3.1 full volume equivalents Load/unload cycles : 36 (0% of expected life) Duty cycle : 25% Power cycles : 20 Cleans : 0 Firmware upgrades : 1 Native data volume read/written (last 4 tapes) : Wrote 170 GB, read 172 GB Drive History Errors returned to host (no host-reported errors found in the fault logs) Drive assessment test history no assessment test results Device analysis history Drive mechanism: No problems have been identified with the drive mechanism. Drive PCA: No problems have been identified with the drive PCA. Write / Read capability: No write / read problems were identified with the drive. Cartridge problems: No cartridge related problems were identified with the drive. Miscellaneous problems: Rule Number : 19 Rule Description : Performance and configuration check SCSI configuration (ID0) : Failed Data Compression configuration (ID1) : Compression Enabled WWN Check (ID2) : Passed Cleaning Check (ID3) : Cleaning not requested Media removal prevented (ID4) : Allowed Problem was last reported : 00:00:00:00 power-on (days:hours:minutes:seconds) ago Device Analysis Device Time Stamps Temperature Measurements Write Error Rate Log Read Error Rate Log Write Error Counters Read Error Counters Sequential Access Counters Tape Usage Log Tape Capacity Log Performance Log Data Compression Log Fault Log Event Log SCSI Command History SCSI Configuration ACI Command History ACI Configuration ADI Command History Drive Trace Log EEPROMS Mechanical EEPROM PCA EEPROM