topic Re: Query: HP MSA 2040 Connectivity failure in MSA Storage

HP MSA 2040 Connectivity failure

Caernside — Mon, 14 Feb 2022 05:23:03 GMT

Hello,

I have an up-to-date MSA 2040 SAS array and a DL380 GEN9 server with an HP H241 Smart HBA card.

Card HBA Drivers : 106.26.0.64(B)

MSA2040 firmware : GL225P002-02

On the server side, with the SSACLI with command "controller all show config detail" i can see my HBA card with the two cables connected (I have the cable ID, the length and the smart part).

On the side of the MSA bay, however, I see all my SAS ports in disconnected status.

Does anyone have an idea of the problem or have encountered this problem?

Query: HP MSA 2040 Connectivity failure

support_s — Sun, 13 Feb 2022 12:44:36 GMT

System recommended content:

1. HPE MSA 2040 User Guide

2. HPE MSA 2040 Storage

Please click on "Thumbs Up/Kudo" icon to give a "Kudo".

Thank you for being a HPE valuable community member.

Re: Query: HP MSA 2040 Connectivity failure

Caernside — Sun, 13 Feb 2022 14:55:19 GMT

Hello, thx for the fast repply.

I have already read the documentation and dont find any solution.

Re: Query: HP MSA 2040 Connectivity failure

sbhat09 — Mon, 14 Feb 2022 05:04:33 GMT

Hello @Caernside,

Have you done the ping test from both the sides? What does the result show?

Regards,
Srinivas Bhat

If you feel this was helpful please click the KUDOS! thumb below!
Note: All of my comments are my own and are not any official representation of HPE.

Re: Query: HP MSA 2040 Connectivity failure

Caernside — Mon, 14 Feb 2022 09:05:36 GMT

Hello @sbhat09 ,

How i can "ping" ?

My equipment is connected in SAS directly.

Have a good day.

Re: Query: HP MSA 2040 Connectivity failure

sbhat09 — Mon, 14 Feb 2022 11:00:40 GMT

Hello @Caernside,

From MSA, I think you can use 'query peer connection' option on page number 112 of this document:

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00017709en_us

Regards,
Srinivas Bhat

If you feel this was helpful please click the KUDOS! thumb below!
Note: All of my comments are my own and are not any official representation of HPE.

Re: Query: HP MSA 2040 Connectivity failure

Caernside — Mon, 14 Feb 2022 14:34:31 GMT

Hey @sbhat09, thx for fast repply,

I have check buit its say : "Specifies the FC WWN or iSCSI IP address of the system to query"

Im in SAS mod and i dont have FC or ISCI .

I can't use the querry command

Re: Query: HP MSA 2040 Connectivity failure

JonPaul — Tue, 15 Feb 2022 18:28:27 GMT

@Caernside
What I would suspect is that the cable is not fully seated.
mini-SAS HD cables have a very small tab to make sure that they are installed correctly which can be overwhelmed and the cable installed upsidedown. First check to make sure the cable is installed in the correct orientation.

Next to check is to make sure the latching mechanism is not interfering with the connection. Gently pull on the cable and if it pulls free then it was not latched. sometimes you have to pull the latch release as you are inserting the cable to get it fully seated.
Lastly but maybe firstly, Is the cable connected into the host ports or the mini-SAS expansion port? The 2040 SAS system has 4x mini-SAS HD host connectors (Basically a square) and 1x mini-SAS expansion connected (rectangle).
For management you will not use any of the SSA utilities. As the H241 will act as a passthru.

Re: Query: HP MSA 2040 Connectivity failure

Caernside — Wed, 16 Feb 2022 18:16:31 GMT

Hey, @Jon

I have find 2 new cable and i find the solution.

The old cable that was with the bay was installed upside down....

Thx all for your help.