firmware

강계정 — Mon, 24 Jul 2006 13:00:00 GMT

안녕하세요...

요즘 비가너무와서 날리도 아닙니다

다름이 아니라 이번에 firmware upgrade할려고 합니다

모델은 superdome(PA-RISC)ll.11입니다

rel_5.4에서 5.5로 upgrade를 하려고 하는데

정확히 어떻게 하는지를 잘 몰라서 도움 요청합니다..

부탁드립니다....(자세한 내요)

감사합니다...

firmware

이태곤 — Mon, 24 Jul 2006 13:00:00 GMT

안녕하십니까

저도 수퍼돔 쪽은 안해봐서리 뭐라고 하기가 그렇지만 매뉴얼대로 하며 무리가 없을것 같습니다..

버전은 Version: 36.8 (8 May 2006) 이네요 rel_5.5가 언제 버전인지요?

현재 util_7.34/PDC 36.8 이 최신입니다.

http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=322811&prodNameId=322813&swEnvOID=7&swLang=13&mode=2&taskId=135&swItem=PF-CSFW0009

위 url에서 다운 받은 것을 다른 hp-ux 11.11 서버에 푸시고 다른 서버에서 fwuu 명령어을 사용하시면 될듯 합니다.

Installation Instructions:

NOTE: Before installing check for service notes.

Applicable service notes will supercede these instructions.

On the Superdome:

1. Shutdown UNIX on all partition(s) using "shutdown -RH".

From another UNIX system open two windows:

2. Extract files:

first unzip: "gunzip PF_CSFW0009.tar.gz"

then untar: "tar -xvf PF_CSFW0009.tar"

3. In the first window telnet into the Superdome's GSP

4. In the second window change to the directory containing the fwuu

executable, Utility firmware and PDC firmware provided in this patch.

5. Type: ./fwuu <Superdome's GSP name>

6. The install program will then display two listings. First it will list

all the firmware ROMs located in the current directory, then it will list

the flash handles associated with the system's hardware. The

second section will contain a line for every firmware entity in the

system and a corresponding flash handle which must be used

to update the entity.

7. the program will prompt: FWUU>

8. Update CIO firmware

Type: 'update FLASH_HANDLE(s) cio.7.4.frm'

where FLASH_HANDLE is the CIO flash handle found in step 6

9. When the update is complete the following message will be displayed:

100 %

Flash Update

Cabinet Entity Type Handle Firmware File Status

_______ ___________ ______ ______________________ _________

0 CIO 769 cio.7.4.frm PASSED

Resetting entity(s) requested for update.....

Continue (yes/no)? : y

Successful reset of all entity(s).

NOTE: All entities of one type may be updated simultaneously by specifying

the FLASH_HANDLES for all entities to be done in the update command.

(i.e. update FLASH_HANDLE_1 FLASH_HANDLE_2 FLASH_HANDLE_3 myclu.frm)

10. Update PDHC firmware

Type: 'update FLASH_HANDLE(s) pdhc.7.10.frm'

11. Update PDC firmware

Type: 'update FLASH_HANDLE(s) hd.bin.36.8.frm'

12. In the first window connected to the GSP power off 48v

on every cabinet in the system.

- GSP:CM> pe

13. Update CLU firmware

Type: 'update FLASH_HANDLE(s) clu.7.8.frm'

14. Update PM firmware

Type: 'update FLASH_HANDLE(s) pm.7.16.frm'

15. Update GSP firmware

Type: 'update FLASH_HANDLE gsp.7.34.frm'

16. In the first window Type: Ctrl ] (that is the Ctrl key on the keyboard)

to break the telnet session and then log back into the GSP.

NOTE: It should take about 2 minutes for the GSP to reboot.

17. Once the GSP has rebooted, AC power cycle cabinet(s).

- AC power off all cabinet(s) in the complex and wait 30 seconds

prior to AC power on to insure TOGO routing is handled by

the new firmware.

When the GSP comes up reset all partitions.

- GSP:CM> rs

then wait 8 minutes for all partitions to boot to BCH.

18. verify that the firmware update is complete by using the sysrev command.

- GSP:CM> sysrev

you should get the following message:

Utility Subsystem FW Revision Level: 7.34

There will also be a list of all firmware revisions in the cabinet

which should be verified for correctness.

HP-UX의 주제 firmware

firmware

firmware