topic Re: Asynchronous I/O...how to enable? in Operating System - HP-UX

Asynchronous I/O...how to enable?

Jerry Jordak — Thu, 14 Dec 2000 15:09:35 GMT

I have a cluster of five L2000s running HP-UX 11.00 and Oracle databases. While the systems are running fine, the DBA for the systems was wanting to know if asynchronous I/O is configured on the servers.

How do I tell if asynchronous I/O is turned on? On an AIX system, which I've been more used to, asynchronous I/O is turned off by default, but to enable or disable it, you just go into smit and turn it on or off. I haven't found anything similar yet in HP-UX, AFAIK.

I did see there is a kernel parameter called "fs_async" which turns on and off asynchronous writes to disk. Is this the parameter I'm looking for to enable asynchronous I/O? If not, what all do I have to do to activate it? It can require a reboot if necessary.

Thanks!

Re: Asynchronous I/O...how to enable?

Rainer_1 — Thu, 14 Dec 2000 15:19:27 GMT

You are right, the fs_async parameter controls the disk IO behavior.

SAM help says:
fs_async specifies whether or not asychronous writing of file-system data structures to disk is allowed. If no value for
fs_async is specified, synchronous writes are used.

Synchronous writes to disk make it easier to restore file system integrity if a system crash occurs while file system data
structures are being updated on the file system.

If asynchronous writes are selected, HP-UX file system semantics for NFS cluster environments are preserved. In
addition, files opened using open() with the 0_SYNC flag (synchronous writing) will continue to be written synchronously
when the asynchronous-writes feature has been configured into the kernel.

Asynchronous writes to disk can improve file system performance significantly. However, asynchronous writes can leave
file system data structures in an inconsistent state in the event of a system crash. For more information about when to
select synchronous or asynchronous writing, refer to the explanatory text later in this help page.

Re: Asynchronous I/O...how to enable?

Alexander M. Ermes — Thu, 14 Dec 2000 15:20:49 GMT

Hi there.
I think, that is the one.
Ask your dba, whether he wants to work with
raw devices. Otherwise don't go for this async
writing. What he would need that for, is setting up log files on raw devices.
Tell him, that this is very tricky,
especially for a restore, if you do not use OmniBack II with the backup of raw devices.
Rgds
Alexander M. Ermes

Re: Asynchronous I/O...how to enable?

James R. Ferguson — Thu, 14 Dec 2000 15:24:14 GMT

Hi:

Yes, fs_async controls whether or not asychronous writing of file-system data structures to disk is allowed. The default is to use synchronous IO.

You can tell if its on (unlikely) with SAM, 'sysdef', or 'kmtune' (on HP 11.0). Use SAM to turn it on if you want (see the second URL below).

For a guide to kernel parameters in HP-UX, see:

http://docs.hp.com/hpux/onlinedocs/os/KCparams.OverviewAll.html

See also, this thread:

http://forums.itrc.hp.com/cm/QuestionAnswer/1,1150,0xf4ab14a24fd1d4118fef0090279cd0f9,00.html

...JRF...

Re: Asynchronous I/O...how to enable?

DIPAK KUMAR ROY — Thu, 14 Dec 2000 15:52:19 GMT

Hi,

You can enable Async I/O by creating a device file called "/dev/async" and enable the same in kernel. Details as below:

Execute following commands as "root":

#mknod /dev/async c 101 0x000004
#chown sybase:sys /dev/async (if you are using SYBASE as your database)
#chmod o-rw /dev/async

This will create the device file needed.
And on the KERNEL side:

1. Edit the file "/stand/system" and give an entry for async i/o:

asyncdsk
asyncdsk_included

2. Rebuild the KERNEL and reboot the system. (Make sure that you have a copy of your running KERNEL).

#mk_kernel -s /stand/system
#kmupdate
# shutdown -yr

Hope this helps you.

Good Luck.

Dipak

Re: Asynchronous I/O...how to enable?

Jerry Jordak — Thu, 14 Dec 2000 16:04:48 GMT

Thanks, Dipak. I will try that the next time I'm allowed to take the system down.

As a point of clarification for me, would it be fair to assume that I would need to enable async I/O through the kernel (following your steps) in addition to just changing the fs_async kernel parameter? I'm just trying to understand what difference I (and the database) will see on the system between enabling async I/O through the kernel via your method and simply changing the kernel parameter.

Re: Asynchronous I/O...how to enable?

DIPAK KUMAR ROY — Thu, 14 Dec 2000 16:38:19 GMT

Jerry,

By default system will use SYNC I/O. And your database loading, dumping .... wil be slow ( I am assuming SYBASE....and I guess it will be similar in case of ORACLE also).

Enabling Async I/O will solve this problem.

Dipak

Re: Asynchronous I/O...how to enable?

Navin Bhat — Wed, 21 Feb 2001 23:32:40 GMT

I have several posts stating that fs_async parameter is used to turn on async writes of data.

This is NOT true.
fs_async just enables async write of META data not the data itself.