topic remshd getservbyname failure. in Operating System - HP-UX

remshd getservbyname failure.

Gino Castoldi_2 — Tue, 06 Apr 2004 10:31:16 GMT

Hi,

HP-UX 11.0 L2000/rp5450 MC/SG 11.09 (2 nodes).

When we run this type of command it fails:

root# remsh server1 date
"remshd: getservbyname"

If we run 'rlogin server1' it works fine.
We are not using NIS.
We do have /.rhosts entries for each server in the cluster. This seems to have stopped working
after we upgraded OVO. No OS patches were applied recently.

10 points to any good answer.
TIA, Gino

Re: remshd getservbyname failure.

RAC_1 — Tue, 06 Apr 2004 10:41:06 GMT

What is the nslookup results for

nslookup server1 and for nslookup "ip_of_server1"

Anil

Re: remshd getservbyname failure.

Robert-Jan Goossens — Tue, 06 Apr 2004 10:44:00 GMT

Hi Gino,

Not shore if you are running 11.0 or 11.i. Check the doc below, patch is for 11.i.

http://www4.itrc.hp.com/service/cki/docDisplay.do?docLocale=en_US&docId=200000062903515

http://www4.itrc.hp.com/service/cki/patchDocDisplay.do?patchId=PHNE_29464

Hope this helps,
Robnert-Jan

Re: remshd getservbyname failure.

Sanjay_6 — Tue, 06 Apr 2004 10:46:25 GMT

Hi Gino,

Check and make sure "kshell" and "ekshell" are uncommented in /etc/services.

Hope this helps.

Regds

Re: remshd getservbyname failure.

Gino Castoldi_2 — Tue, 06 Apr 2004 10:50:41 GMT

Hi,

RAC: nslookup results are the same for the hostname and ip address.

Robert-Jan: We're running HP-UX 11.0.

Sanjay: I'll un-comment those entries in the
/etc/services files and then will do a
'inted -c'.

10 points to any good answer.
TIA, Gino

Re: remshd getservbyname failure.

Robert-Jan Goossens — Tue, 06 Apr 2004 10:53:41 GMT

Gino,

Always forgetting that you are in the US :-)

Document description: Cannot remsh to remote sys; error msg: 'remshd getservbyname'
Document id: 2200103257

US
http://www1.itrc.hp.com/service/cki/docDisplay.do?docLocale=en_US&docId=200000062903515

Regards,
Robert-Jan

Re: remshd getservbyname failure.

Gino Castoldi_2 — Tue, 06 Apr 2004 11:02:32 GMT

Hi,

I uncommented "kshell" and "ekshell" in
/etc/services and in inetd.conf I uncommented
"kshell" and did a 'inetd -c' but it still gets the same error messages.

10 points to any good answer.
TIA, Gino

Re: remshd getservbyname failure.

Gino Castoldi_2 — Tue, 06 Apr 2004 11:15:42 GMT

Hi,

I spoke too soon. It does work now.
I had to make the same changes on both servers in the cluster (that usually helps...).

Thank you everyone for your help and suggestions.

10 points to any good answer.
TIA, Gino