topic Re: Streams/UX errors from console in Operating System - HP-UX

Streams/UX errors from console

Yeow Peng — Thu, 04 Oct 2007 22:54:31 GMT

Hi all,

I faced some problem with my HPUX 11i A400 machine. Seen multiple Stream/UX errors from console pointing to "639 tcp_timer:strange state (-6)" when OS starts its service at network tracing and logging level.

Other problem faced when I am able to login to the machine.

1) ioscan shows 2 lancard "Claimed" with lan0 and lan1, but lanscan sometimes shows either lan0 and lan1 or lan1 and lan100.
2) Did ifconfig on either interfaces and "no interface" seen.
3) Check /etc/rc.config.d/netconf and seen that the configurations are set correctly.
4) From SAM, both lancards shows "Not configured". Not able configure.
5) From netstat -rn, only shows local loopback address.

I am able to perform the workaround by setting IP address on lan100 to ping to other machines. But when I rebooted the machine again, the same Streams/UX errors occurred.

Need help.

Thanks in advance.

Regrds,
yeow peng

Re: Streams/UX errors from console

TY 007 — Thu, 04 Oct 2007 23:12:42 GMT

Hello Yeow Peng,

Following 11.11 OS Patches should have been loaded in:
PHNE_30450 nettl(1M), netfmt(1M) and nettladm(1M) patch
PHNE_34427 LAN product cumulative patch
PHNE_35453 Cumulative STREAMS Patch
PHNE_35939 Cumulative Mux and Pty Patch
PHNE_36441 Streams Pty cumulative patch

Thanks

Re: Streams/UX errors from console

TY 007 — Thu, 04 Oct 2007 23:16:36 GMT

Hello Yeow Peng,

>> lan0 and lan1 or lan1 and lan100

APA - Auto-Port Aggregation?

Load in this as well:
PHNE_36483 APA B.11.11.[00-21] cumulative patch

Thanks

Re: Streams/UX errors from console

Sameer_Nirmal — Thu, 04 Oct 2007 23:22:09 GMT

I would suggest to check the cumulative ARPA Transport patch level.

Re: Streams/UX errors from console

Yeow Peng — Fri, 05 Oct 2007 00:04:45 GMT

Hi all,

This problem occurs after I recovers the machine using make_recovery from tape. I did set the IP address for the machine during the interactive ignite recovery. But somehow, the interface did not take the IP into account.

Other than that, when I rebooted the machine, lanscan shows lan0 and lan1. When rebooted the machine again, it shows lan1 and lan100 instead. So where does lan0 goes?

I do not see such streams/ux errors from the rest of the A400 machines on my platform.

Thanks for all your advices.

Regrds,
yeow peng

Re: Streams/UX errors from console

whiteknight — Fri, 05 Oct 2007 01:34:10 GMT

Yeow Peng,

Firstly fixed your network and tracing issue

1. cd /var/adm
2. nettl -stop
3. mv nettl.LOG000 nettl.LOG000.old
4. nettl -start

WK

Re: Streams/UX errors from console

leelangco_1 — Sat, 06 Oct 2007 06:30:33 GMT

yepow peng,

is the recovery tape made from your A400 machine? if it comes from another machine it may cause problem.have you checked your /etc/rc.log for some "fail" key words?

Re: Streams/UX errors from console

Yeow Peng — Tue, 09 Oct 2007 11:05:55 GMT

Hi all,

I have managed to solve my problem through your advices.

Thanks.

yeow peng

Re: Streams/UX errors from console

leelangco_1 — Tue, 09 Oct 2007 20:35:38 GMT

how to slove that ?
do not forget to assign points!

Re: Streams/UX errors from console

whiteknight — Wed, 10 Oct 2007 02:01:13 GMT

Yeow Peng,

please assign points and close the thread.

please take a moment to give them credit for their assistance!

http://forums1.itrc.hp.com/service/forums/helptips.do?#33