ARRAY ACCELERATOR (CACHE) : Battery Status (pack #1)...FAILED

Mcdon_1 — Tue, 06 May 2008 04:35:41 GMT

Hi,

We are getting following out put from the sautil command.

# uname -a
HP-UX metlifeD B.11.11 U 9000/800 3204796273 unlimited-user license

# sautil /dev/ciss4 | more

******************************************************************************
**** ****
**** S A U T I L S u p p o r t U t i l i t y ****
**** ****
**** for the HP SmartArray RAID Controller Family ****
**** ****
**** version A.02.12 ****
**** ****
**** (C) Copyright 2003-2007 Hewlett-Packard Development Company, L.P. ****
******************************************************************************

---- DRIVER INFORMATION ------------------------------------------------------

Driver State........................ READY

---- CONTROLLER INFORMATION --------------------------------------------------

Controller Product Number........... A9890A
Controller Product Name............. HP PCI-X SmartArray 6402
Hardware Path....................... 0/2/1/0/4/0
Serial Number....................... P5782ACXQTW0JM
Device File......................... /dev/ciss4
Hardware Revision................... 'B'
Boot Block Revision................. 5.76
Firmware Revision (running)......... 2.68
Firmware Revision (in ROM).......... 2.68
Firmware Revision (inactive)........ 2.58
# of Logical Drives................. 1
# of Physical Disks Configured...... 5
# of Physical Disks Detected........ 5
Logical Drive Rebuild Priority...... 118 (high)
Array Capacity Expansion Priority... 0 (low)
Auto-Fail Missing Disks at Boot..... enabled
SCSI Transfer Detection Mode........ Auto Detect

---- ARRAY ACCELERATOR (CACHE) INFORMATION -----------------------------------

Array Accelerator Board Present?.... yes
Cache Configuration Status.......... write cache temporarily disabled (code=1)
Cache Ratio......................... 50% Read / 50% Write
Total Cache Size (MB)............... 128
Read Cache........................ 064
Write Cache....................... 064
Transfer Buffer................... 000
Battery Pack Count.................. 2
Battery Status (pack #1)............ FAILED
Battery Status (pack #2)............ ok

---- LOGICAL DRIVE SUMMARY ---------------------------------------------------

# RAID Size Status

0 5 858293 MB OK

---- SCSI DEVICE SUMMARY -----------------------------------------------------

Location Ch ID Type Capacity Status

external 1 0 DISK 300.0 GB OK
external 1 1 DISK 300.0 GB OK
external 1 2 DISK 300.0 GB OK
external 1 3 DISK 300.0 GB OK
external 1 4 DISK 300.0 GB SPARE
external 1 7 PROCESSOR

---- SCSI BUS SUMMARY --------------------------------------------------------

External Internal
Ch LVD_Mode Connector Connector

1 YES YES -
2 YES - -

---- LOGICAL DRIVE 0 ---------------------------------------------------------

Logical Drive Device File........... c4t0d0
Fault Tolerance Mode................ RAID 5 (Distributed Data Guarding)
Logical Drive Size.................. 858293 MB
Logical Drive Status................ OK
# of Participating Physical Disks... 4

Participating Physical Disk(s)...... Ch:ID
1: 0
1: 1
1: 2
1: 3

Participating Spare Disk(s)......... Ch:ID
1: 4

Stripe Size......................... 32 KB
Logical Drive Cache Status.......... write cache temporarily disabled (code=1)
Configuration Signature............. 0x0
Media Exchange Detected?............ no

---- SCSI DEVICE 1:0 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 0
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BD3008A4C6
Device Serial Number............................. 3KR383Q10000972003WG
Device Firmware Version.......................... HPB4
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes

And so on for the other DISKS.

I have a concern about the battery pack#1, since it gives the following message :

Battery Status (pack #1)............ FAILED

Is the Battery pack#1 faulty?

Re: ARRAY ACCELERATOR (CACHE) : Battery Status (pack #1)...FAILED

Torsten. — Tue, 06 May 2008 04:40:55 GMT

The battery is bad and should be replaced asap. Open a support call and get a new battery installed.
After this your system will be faster again, because the write cache will be enabled.

Re: ARRAY ACCELERATOR (CACHE) : Battery Status (pack #1)...FAILED

Kapil Jha — Tue, 06 May 2008 04:41:42 GMT

Hello Battery is failed/discharged so open a h/w case and change the battery.
BR,
Kapil

Re: ARRAY ACCELERATOR (CACHE) : Battery Status (pack #1)...FAILED

Mcdon_1 — Tue, 06 May 2008 04:52:58 GMT

Thaks for your support.

topic Re: ARRAY ACCELERATOR (CACHE) : Battery Status (pack #1)...FAILED in Operating System - HP-UX

ARRAY ACCELERATOR (CACHE) : Battery Status (pack #1)...FAILED

Re: ARRAY ACCELERATOR (CACHE) : Battery Status (pack #1)...FAILED

Re: ARRAY ACCELERATOR (CACHE) : Battery Status (pack #1)...FAILED

Re: ARRAY ACCELERATOR (CACHE) : Battery Status (pack #1)...FAILED