topic Re: Installing Modem on RP3410 in Operating System - HP-UX

Installing Modem on RP3410

Marie-France Paquet — Thu, 15 May 2008 13:31:49 GMT

Hello,

I'm trying to install a modem on my RP3410 using 1 of the 3 ports on my Serial Card but I can't have the modem answering (the modem is set to Auto Answer). I used SAM to configure the modem (9600) on Port #4. I have this line in my inittab file "a0:3:respawn:/usr/lbin/uucp/uugetty -r -t 60 -h ttyd1p4 9600". When I call the modem using "cu -m -l /dev/cul1p4 -s 9600 dir" I get a "Connected" message but it never answers back. What is the problem ?

Thank you for any help.

Re: Installing Modem on RP3410

Robert-Jan Goossens — Thu, 15 May 2008 13:57:23 GMT

Hi Marie-France,

Maybe this will help.

Title: Modem: installing a MT5634ZBA Modem on the N/L-Class System

http://www11.itrc.hp.com/service/cki/docDisplay.do?docLocale=en&docId=emr_na-c00958996-2

Regards,
Robert-Jan

Re: Installing Modem on RP3410

Steven E. Protter — Thu, 15 May 2008 14:10:26 GMT

Shalom,

Is the modem a supported modem for HP-UX?

Try testing on it prior to use. See if anything shows up in /var/adm/syslog/syslog.log

SEP

Re: Installing Modem on RP3410

Marie-France Paquet — Thu, 15 May 2008 14:14:26 GMT

Yes, the modem was used before on an other HP Server (L1000). It was connected throw a 8 port mux card and it worked fine. It is a GVC 14400.

Re: Installing Modem on RP3410

Marie-France Paquet — Thu, 15 May 2008 14:21:05 GMT

I am connected in the "Remote" port. Does this port accept 9600 baud rate ? What is the maximum baud rate I can configure on this port ? Since my modem is a 14400, can I upgrade my configuration to 14400 ?

Re: Installing Modem on RP3410

Torsten. — Thu, 15 May 2008 14:28:47 GMT

The built-in remote port is listed as port 2 in ioscan

tty 1 0/7/1/1 asio0 CLAIMED INTERFACE PCI Serial (103c1048)
/dev/GSPdiag1 /dev/mux1 /dev/tty1p2
/dev/diag/mux1 /dev/tty1p0 /dev/tty1p4

Not really sure at the moment about port 4, but I guess you are on the wrong port.

Re: Installing Modem on RP3410

Torsten. — Thu, 15 May 2008 14:39:00 GMT

The port settings are configured from the MP interface:

MP:CM> ca

CA

This command allows you to modify the local and remote modem serial port
configurations.

Local and Remote Serial Port Configuration Menu:
D - Display Local/Remote Serial Port Configuration
L - Modify Local Serial Port Configuration
R - Modify Remote/Modem Serial Port Configuration

Enter menu item or [Q] to Quit: d
d

Current Local Serial Port Configuration:
Bit Rate in bits/sec : 9600
Flow Control : Software

Current Remote/Modem Serial Port Configuration:
Bit Rate in bits/sec : 19200
Flow Control : Software
Modem Presence : Always connected
Modem Protocol : CCITT
Transmit Configuration Strings : Enabled

Local and Remote Serial Port Configuration Menu:
D - Display Local/Remote Serial Port Configuration
L - Modify Local Serial Port Configuration
R - Modify Remote/Modem Serial Port Configuration

Enter menu item or [Q] to Quit: r
r

Current Remote/Modem Serial Port Configuration:
B - Bit Rate in bits/sec : 19200
F - Flow Control : Software
M - Modem Presence : Always connected
P - Modem Protocol : CCITT
T - Transmit Configuration Strings : Enabled

Enter parameter(s) to change, A to modify All, or [Q] to Quit: b
b

For each parameter, enter:
New value, or
to retain the current value, or
DEFAULT to set the default value, or
Q to Quit

Remote/Modem Bit Rate in bits/sec:
Current -> 19200 (default)
Options: 4800, 9600, 19200, 38400

Enter new value, or Q to Quit:

check the status:

MP:CM> ms

MS

Type to update modem status, or Q to quit

-Modem state- -------------- Remote port Modem Signals -------------

RTS/105 DTR/108 CTS/106 DSR/107 DCD/109 RI/125

Session idle 0 0 0 0 0 0

MP:CM> sa

SA

This command allows you to modify MP access configuration.

Current Set Access Configuration:
R - Remote/Modem : OS SESSION
T - Telnet : Enabled
W - Web SSL : Enabled
- - SSH : Disabled (MP Feature Not Licensed)
I - IPMI over LAN : Enabled

Enter parameter(s) to change, A to modify All, or [Q] to Quit: r
r

For each parameter, enter:
New value, or
to retain the current value, or
DEFAULT to set the default value, or
Q to Quit

Remote/Modem serial port Access Configuration:
L - LOCKED
(No dial-in access allowed)
M - MANAGEMENT ACCESS
(For both dial-in and outgoing paging)
Current -> O - OS SESSION (default)
(Management and Console access will be denied from the
modem. Incoming access will result in an OS Session
outgoing paging will not preempt the OS)

Enter new value, or Q to Quit:

Re: Installing Modem on RP3410

Marie-France Paquet — Thu, 15 May 2008 18:14:05 GMT

Hi Torsten,

Thanks a lot for your long and explicite answer. I followed it step by step and modified the remote port speed rate to 9600. Any other else parameters are the same, but when a run the "MS" command to see the modem state, I don't get a 0 under CTS/106, I get a 1 on that status. For the access configuration, I have the default "O - OS SESSION". Is that correct ?

But unfortunately, after all this is done, I still get no answer from my modem.

Here is what I get :
[xxx:/]$ cu -m -l /dev/cul1p4 -s 9600 dir
Connected
~[xxx].

Disconnected
[xxx:/]$

Do you see anything else I should look forward ?

Re: Installing Modem on RP3410

Torsten. — Thu, 15 May 2008 18:16:01 GMT

Please read my first post again - I still think you configured the wrong port.

Re: Installing Modem on RP3410

Marie-France Paquet — Thu, 15 May 2008 18:58:21 GMT

I tried port 2 but it's the same story (no answer back).

Here is what I have in my ioscan :
tty 0 0/7/1/0 asio0 CLAIMED INTERFACE PCI SimpleComm (103c1290)
tty 1 0/7/1/1 asio0 CLAIMED INTERFACE PCI Serial (103c1048)

Herer is what I have in my /etc/inittab file :
a0:3:respawn:/usr/lbin/uucp/uugetty -r -t 60 -h ttyd1p4 9600

Does it help ?

Re: Installing Modem on RP3410

Torsten. — Fri, 16 May 2008 04:09:38 GMT

Port 2 is /dev/tty1p2