topic Re: changed hostname and server hangs? in Operating System - HP-UX

changed hostname and server hangs?

Jerry_109 — Sat, 17 Jan 2009 00:02:04 GMT

HP-UX B.11.31 Uia64 hp server rx7640
####################################
executed :
"set_parms hostname" to change hostname and after reboot system hangs at :

##################################
Starting ISEE hpservices mad daemon. ......................... N/A
Starting X Font Server at TCP port 7000 ...................... N/A
Start vt daemon .............................................. N/A
Start time synchronization ................................... OK
Start accounting ............................................. N/A
Starting Veritas Enterprise Administrator Service (vxsvc) ...

###############################

Please advise

Re: changed hostname and server hangs?

sujit kumar singh — Sat, 17 Jan 2009 06:57:14 GMT

hi

just try to do a CTRL+\

the system shud boot past that.

are u able to telnet to the server as i think the network Services should have started.

Regards
Sujit

Re: changed hostname and server hangs?

Asif Sharif — Sat, 17 Jan 2009 12:18:23 GMT

Hi Jerry,

ctrl+\ is synonymous and skip over the hung startup script followed by executing the next one in the sequence.

Regards,
Asif Sharif

Re: changed hostname and server hangs?

Bill Hassell — Sun, 18 Jan 2009 00:58:04 GMT

Changing the hostname can create a number of problems if not done with careful planning. Does your server user DNS? Do the clients use DNS? Did the IP address change? Did the DNS server get updated with the new hostname? Does the server run NFS or CIFS/SAMBA? Does the server run email services?

Any of these questions will require a clear answer about how to accommodate a hostname change.

Re: changed hostname and server hangs?

Avinash20 — Sun, 18 Jan 2009 09:22:52 GMT

Please see that the hostname change is also made in /etc/hosts and DNS server is any !!

Re: changed hostname and server hangs?

skt_skt — Sun, 18 Jan 2009 15:47:27 GMT

did u try rebootinf w/o hostname change. Was it able come up?

Re: changed hostname and server hangs?

Jerry_109 — Wed, 21 Jan 2009 00:59:18 GMT

Thanks All,

Found the following information in /etc/rc.log :

####################
startup seems to be a sizing problem with ARIES as follows :

#########################################
745 [HP ARIES32]: ***** Log time: Tue Jan 20 14:06:46 PST 2009 *****
746 [HP ARIES32]:
747 [HP ARIES32]: ARIES Limitation [PID : 2301]
748 [HP ARIES32]: ARIES cannot proceed emulation because:
749 [HP ARIES32]:
750 [HP ARIES32]: PID 2301 received SIGSEGV for stack growth failure.
751 [HP ARIES32]: Possible causes - insufficient memory or swap space, or
752 [HP ARIES32]: PA-RISC application stack size exceeded maximum available
754 [HP ARIES32]:
755 [HP ARIES32]: Increase the value of -ssz ARIES parameter and kernel tunable
756 [HP ARIES32]: pa_maxssiz_32bit.
757 [HP ARIES32]:
758 [HP ARIES32]: ARIES does not support applications which are nearly
759 [HP ARIES32]: or completely maxed out on their data segment address
760 [HP ARIES32]: space usage. This is because ARIES consumes small amount of
761 [HP ARIES32]: virtual memory address space of the emulated application.
762 [HP ARIES32]:
763 [HP ARIES32]: Terminating emulation.
764 [HP ARIES32]:
765 [HP ARIES32]: ARIES Version :
766 [HP ARIES32]: 11.31 (PHSS_37553) Ver: 3.0.00015 [May 4, 2008 23:49:23]
767 [HP ARIES32]: Invoked command :
768 [HP ARIES32]:
#########################################
# kctune :
maxssiz 134217728 134217728 Immed
maxssiz_64bit 1073741824 1073741824 Immed
pa_maxssiz_32bit 83648512 Default
pa_maxssiz_64bit 536870912 Default
#########################################
####################

Re: changed hostname and server hangs?

Dennis Handly — Wed, 21 Jan 2009 01:06:32 GMT

>pa_maxssiz_32bit 83648512

Does increasing pa_maxssiz_32bit help? Try 120 Mb.

Re: changed hostname and server hangs?

Jerry_109 — Wed, 21 Jan 2009 17:18:58 GMT

No, it still hung with the same message in rc.log. I changed the tunable as follows :

###############
# kctune -v pa_maxssiz_32bit
Tunable pa_maxssiz_32bit
Description Maximum size of the stack segment of a 32-bit PA-RISC process (bytes)
Module vm
Current Value 468713472
Value at Next Boot 468713472
Value at Last Boot 468713472
Default Value 83648512
Constraints pa_maxssiz_32bit >= 83648512
pa_maxssiz_32bit <= 468713472
Can Change At Next Boot Only
###########################

mesage from rc.log :

Starting Veritas Enterprise Administrator Service (vxsvc)
Output from "/sbin/rc2.d/S700isisd start":
----------------------------

[HP ARIES32]: ***** Log time: Wed Jan 21 08:46:03 PST 2009 *****
[HP ARIES32]:
[HP ARIES32]: ARIES Limitation [PID : 2300]
[HP ARIES32]: ARIES cannot proceed emulation because:
[HP ARIES32]:
[HP ARIES32]: PID 2300 received SIGSEGV for stack growth failure.
[HP ARIES32]: Possible causes - insufficient memory or swap space, or
[HP ARIES32]: PA-RISC application stack size exceeded maximum available
[HP ARIES32]: stack size in ARIES.
[HP ARIES32]:
[HP ARIES32]: Increase the value of -ssz ARIES parameter and kernel tunable
[HP ARIES32]: pa_maxssiz_32bit.
[HP ARIES32]:
[HP ARIES32]: ARIES does not support applications which are nearly
[HP ARIES32]: or completely maxed out on their data segment address
[HP ARIES32]: space usage. This is because ARIES consumes small amount of
[HP ARIES32]: virtual memory address space of the emulated application.
[HP ARIES32]:
[HP ARIES32]: Terminating emulation.
[HP ARIES32]:
[HP ARIES32]: ARIES Version :
[HP ARIES32]: 11.31 (PHSS_37553) Ver: 3.0.00015 [May 4, 2008 23:49:23]
[HP ARIES32]: Invoked command :
[HP ARIES32]:
###############

Re: changed hostname and server hangs?

Jerry_109 — Wed, 21 Jan 2009 23:18:19 GMT

Received following coredump when executing java1.3. :

# file core
core: ELF-32 core file - IA64 from 'java' - received SIGSEGV

Is this a tunable problem?

##################################
root@vulpolicyp[/opt/java1.3/jre/bin]
# uname -a ; model
HP-UX vulpolicyp B.11.31 U ia64 2066127389 unlimited-user license
ia64 hp server rx7640
root@vulpolicyp[/opt/java1.3/jre/bin]
# ./java
Memory fault(coredump)
root@vulpolicyp[/opt/java1.3/jre/bin]
# ll
total 25552
-r-xr-xr-x 1 bin bin 8035 Feb 5 2007 .java_wrapper
lrwxrwxr-x 1 bin bin 13 Jan 21 14:21 .start_xfs -> .java_wrapper
-r-xr-xr-x 1 bin bin 20480 Feb 5 2007 HPUXChildWrapper
dr-xr-xr-x 3 bin bin 96 Jan 21 14:21 IA64
-rw------- 1 root sys 7948220 Jan 21 15:12 core
lrwxrwxr-x 1 bin bin 13 Jan 21 14:21 java -> .java_wrapper
lrwxrwxr-x 1 bin bin 13 Jan 21 14:21 jcpm_server -> .java_wrapper
lrwxrwxr-x 1 bin bin 13 Jan 21 14:21 keytool -> .java_wrapper
lrwxrwxr-x 1 bin bin 13 Jan 21 14:21 policytool -> .java_wrapper
lrwxrwxr-x 1 bin bin 13 Jan 21 14:21 rmid -> .java_wrapper
lrwxrwxr-x 1 bin bin 13 Jan 21 14:21 rmiregistry -> .java_wrapper
lrwxrwxr-x 1 bin bin 13 Jan 21 14:21 tnameserv -> .java_wrapper
root@vulpolicyp[/opt/java1.3/jre/bin]
# file core
core: ELF-32 core file - IA64 from 'java' - received SIGSEGV

Re: changed hostname and server hangs?

Dennis Handly — Wed, 21 Jan 2009 23:18:31 GMT

>I changed the tunable as follows:
Current Value 468713472

This is way too big! You have just taken 468 Mb away from maxdsiz. You should put it back to a more reasonable value like 120 Mb.

Since it still fails, you have a bug, a recursive stack overflow. And you should fire up gdb to get a stack trace.

What is the executable in question, vxsvc?

Re: changed hostname and server hangs?

Dennis Handly — Wed, 21 Jan 2009 23:21:13 GMT

>Received following coredump when executing java1.3:
>core: ELF-32 core file - IA64 from 'java' - received SIGSEGV
>Is this a tunable problem?

You think it is related? Do you have enough swap? What does "swapinfo -tam" show?

For both problems, you should be talking to the Response Center. To look at your aries and java core dumps.

Re: changed hostname and server hangs?

Jerry_109 — Wed, 21 Jan 2009 23:24:04 GMT

ok, sounds like a good ideal. I'll a call w/ HP.

root@vulpolicyp[/sbin/rc2.d]
# ll /sbin/rc2.d/S700isisd
lrwxr-xr-x 1 root sys 18 Dec 30 11:21 /sbin/rc2.d/S700isisd -> /sbin/init.d/isisd

#########################
root@vulpolicyp[/sbin/rc2.d]
# ps -aef | grep -i vxsvc
root 2300 1 238 08:46:00 ? 397:22 /opt/VRTSob/bin/vxsvc -m
root 7233 3044 0 15:23:32 pts/0 0:00 grep -i vxsvc
root@vulpolicyp[/sbin/rc2.d]
# swapinfo -tam
Mb Mb Mb PCT START/ Mb
TYPE AVAIL USED FREE USED LIMIT RESERVE PRI NAME
dev 8192 0 8192 0% 0 - 1 /dev/vg00/swap
dev 24576 0 24576 0% 0 - 1 /dev/vg00ext/swap2
reserve - 1173 -1173
memory 24432 2854 21578 12%
total 57200 4027 53173 7% - 0 -

Re: changed hostname and server hangs?

Dennis Handly — Wed, 21 Jan 2009 23:49:00 GMT

>root 2300 1 238 08:46:00 ? 397:22 /opt/VRTSob/bin/vxsvc -m

Since vxsvc is running, what was aborting? Do you have a core file?

>Total 57200 4027 53173 7%

Looks like you have enough swap.

Re: changed hostname and server hangs?

avizen9 — Thu, 22 Jan 2009 09:13:38 GMT

HI Jerry,
can you send me bdf -l command output and also dmesg thanks

Re: changed hostname and server hangs?

scifusers — Thu, 22 Jan 2009 16:10:10 GMT

Dennis : yes there is a core file as follows :
root@vulpolicyp[/opt/java1.3]
# ll /opt/java1.3/jre/bin/core
-rw------- 1 root sys 7948220 Jan 21 15:12 /opt/java1.3/jre/bin/core
root@vulpolicyp[/opt/java1.3]
# file /opt/java1.3/jre/bin/core
/opt/java1.3/jre/bin/core: ELF-32 core file - IA64 from 'java' - received SIGSEGV

#########################################

Re: changed hostname and server hangs?

scifusers — Thu, 22 Jan 2009 16:14:56 GMT

Avizena :
This is Jerry,
Here is the bdf -l & dmesg :

root@vulpolicyp[/opt/java1.3]
# bdf -l
Filesystem kbytes used avail %used Mounted on
/dev/vg00/root 4128768 429312 3670616 10% /
/dev/vg00/stand 4128768 333592 3765616 8% /stand
/dev/vgdata01/wiis 20512768 71673 19163533 0% /wiis
/dev/vg00/var 33554432 1327992 31975000 4% /var
/dev/vg00/crash 8912896 21120 8822448 0% /var/adm/crash
/dev/vg00/usr 8912896 3035896 5831136 34% /usr
/dev/vgbackup/u99 307232768 141947 287897652 0% /u99
/dev/vglog/u98 51249152 79205 47971833 0% /u98
/dev/vgdata01/u02 235536384 124374 220698767 0% /u02
/dev/vgdata01/u01 235536384 921300 219951719 0% /u01
/dev/vgdata01/u00 20512768 8838201 10944928 45% /u00
/dev/vg00/tmp 8912896 1330840 7524408 15% /tmp
/dev/vg00/scif 1048576 56024 984808 5% /scif
/dev/vg00/opt 15073280 7473216 7540800 50% /opt
/dev/vg00/home 8912896 21368 8822192 0% /home
/dev/vgdata01/edata
112656384 95128 105526183 0% /edata
/dev/vgdata01/app 10289152 20014 9627324 0% /app
DevFS 3 3 0 100% /dev/deviceFileSystem
#################################
Jan 22 08:13
Loaded ACPI revision 2.0 tables.
MMIO on this platform supports Write Coalescing.
Warning: Setting the expanded_node_host_names parameter to 1 will allow administrators to set node and host names larger than 8 and 64 chara
cters/bytes, respectively. It is strongly recommended that all related manpages and documentation be understood before setting larger names
. Larger names can cause some applications which use those names to behave incorrectly or fail.

Using /stand/ext_ioconfig

Memory Class Setup
-------------------------------------------------------------------------
Class Physmem Lockmem Swapmem
-------------------------------------------------------------------------
System : 24431 MB 24431 MB 24431 MB
Kernel : 24431 MB 24431 MB 24431 MB
User : 22995 MB 22529 MB 22535 MB
-------------------------------------------------------------------------

ktracer is off until requested.
Installing Socket Protocol families AF_INET and AF_INET6
Lowfat driver is the master here
64000/0xfa00 esvroot
Kernel EVM initialized
sec_init(): kernel RPC authentication/security initialization.
secgss_init(): kernel RPCSEC_GSS security initialization.
rpc_init(): kernel RPC initialization.
rpcmod_install(): kernel RPC STREAMS module "rpcmod" installation. ...(driver_install)
NOTICE: nfs_client_pv3_install(): nfs3 File system was registered at index 11.
NOTICE: nfs_client_pv4_install(): nfs4 File system was registered at index 12.
NOTICE: cachefsc_install: cachefs File system was registered at index 14.
btlan_load() Loaded Successfully
1 cell
1/0 sba
1/0/0 lba
Initializing the Ultra320 SCSI Controller at 1/0/0/3/0. Controller firmware version is 01.03.35.65
1/0/0/3/0 mpt
Initializing the Ultra320 SCSI Controller at 1/0/0/3/1. Controller firmware version is 01.03.35.65
1/0/0/3/1 mpt
1/0/1 lba
1/0/1/1 pci_slot
1/0/1/1/0 PCItoPCI
Initializing the Ultra320 SCSI Controller at 1/0/1/1/0/4/0. Controller firmware version is 01.03.35.69
1/0/0/3/1.0x2 estp
1/0/1/1/0/4/0 mpt
Initializing the Ultra320 SCSI Controller at 1/0/1/1/0/4/1. Controller firmware version is 01.03.35.69
1/0/1/1/0/4/1 mpt
1/0/1/1/0/6/0 iether
1/0/1/1/0/6/1 iether
1/0/2 lba
1/0/2/1 pci_slot
1/0/4 lba
1/0/4/1 pci_slot
1/0/4/1/0 PCItoPCI
fcd: Claimed HP AD194-60001 4Gb Fibre Channel port at hardware path 1/0/4/1/0/4/0 (FC Port 1 on HBA)
1/0/4/1/0/4/0 fcd
fcd: Claimed HP AD194-60001 4Gb Fibre Channel port at hardware path 1/0/4/1/0/4/1 (FC Port 2 on HBA)
1/0/4/1/0/4/1 fcd
1/0/4/1/0/6/0 iether
1/0/4/1/0/6/1 iether
1/0/6 lba
1/0/6/1 pci_slot
1/0/6/1/0 PCItoPCI
fcd: Claimed HP AD194-60001 4Gb Fibre Channel port at hardware path 1/0/6/1/0/4/0 (FC Port 1 on HBA)
1/0/6/1/0/4/0 fcd
fcd: Claimed HP AD194-60001 4Gb Fibre Channel port at hardware path 1/0/6/1/0/4/1 (FC Port 2 on HBA)
1/0/6/1/0/4/1 fcd
1/0/6/1/0/6/0 iether
1/0/6/1/0/6/1 iether
1/0/8 lba
1/0/8/1 pci_slot
1/0/10 lba
1/0/0/3/0.0x6 estp
1/0/0/3/0.0x6.0x0 eslpt
1/0/0/3/0.6 tgt
1/0/0/3/0.6.0 sdisk
1/0/10/1 pci_slot
1/0/12 lba
1/0/12/1 pci_slot
1/0/12/1/0 PCItoPCI
fcd: Claimed HP AD194-60001 4Gb Fibre Channel port at hardware path 1/0/12/1/0/4/0 (FC Port 1 on HBA)
1/0/12/1/0/4/0 fcd
fcd: Claimed HP AD194-60001 4Gb Fibre Channel port at hardware path 1/0/12/1/0/4/1 (FC Port 2 on HBA)
1/0/12/1/0/4/1 fcd
1/0/12/1/0/6/0 iether
1/0/12/1/0/6/1 iether
1/0/14 lba
1/0/14/1 pci_slot
1/0/14/1/0 PCItoPCI
fcd: Claimed HP AD194-60001 4Gb Fibre Channel port at hardware path 1/0/14/1/0/4/0 (FC Port 1 on HBA)
1/0/14/1/0/4/0 fcd
fcd: Claimed HP AD194-60001 4Gb Fibre Channel port at hardware path 1/0/14/1/0/4/1 (FC Port 2 on HBA)
1/0/14/1/0/4/1 fcd
1/0/14/1/0/6/0 iether
1/0/14/1/0/6/1 iether
1/120 processor
1/121 processor
1/122 processor
1/123 processor
1/250 pdh
1/250/0 acpi_node
1/250/1 ipmi
1/250/2 asio0
1/0/0/3/1.0x2.0x0 eslpt
1/0/0/3/1.2 tgt
1/0/0/3/1.2.0 sdisk
1/0/6/1/0/4/0.0x50060e8010037607 estp
1/0/6/1/0/4/0.0x50060e8005b26e23 estp
1/0/6/1/0/4/0.0x50060e8005b26e23.0x0 eslpt
1/0/6/1/0/4/0.0x50060e8010037607.0x0 eslpt
1/0/6/1/0/4/0.0x50060e8005b26e23.0x4000000000000000 eslpt
1/0/6/1/0/4/0.0x50060e8010037607.0x1000000000000 eslpt
1/0/6/1/0/4/0.10 fcd_fcp
1/0/6/1/0/4/0.10.121.255.0 fcd_vbus
1/0/6/1/0/4/0.10.121.255.0.0 tgt
1/0/6/1/0/4/0.10.121.255.0.0.0 sdisk
1/0/6/1/0/4/0.10.121.255.0.0.1 sdisk
1/0/6/1/0/4/0.0x50060e8005b26e23.0x4001000000000000 eslpt
1/0/6/1/0/4/0.0x50060e8005b26e23.0x4002000000000000 eslpt
1/0/6/1/0/4/0.0x50060e8005b26e23.0x4003000000000000 eslpt
1/0/6/1/0/4/0.0x50060e8005b26e23.0x4004000000000000 eslpt
1/0/6/1/0/4/0.0x50060e8005b26e23.0x4008000000000000 eslpt
1/0/6/1/0/4/0.10.123.255.0 fcd_vbus
1/0/6/1/0/4/0.10.123.255.0.0 tgt
1/0/6/1/0/4/0.10.123.255.0.0.0 sctl
1/0/6/1/0/4/0.10.123.0.0 fcd_vbus
1/0/6/1/0/4/0.10.123.0.0.0 tgt
1/0/6/1/0/4/0.10.123.0.0.0.0 sdisk
1/0/6/1/0/4/0.10.123.0.0.0.1 sdisk
1/0/6/1/0/4/0.10.123.0.0.0.2 sdisk
1/0/6/1/0/4/0.10.123.0.0.0.3 sdisk
1/0/6/1/0/4/0.10.123.0.0.0.4 sdisk
1/0/6/1/0/4/0.10.123.0.0.1 tgt
1/0/6/1/0/4/0.10.123.0.0.1.0 sdisk
1/0/1/1/0/4/1.0x6 estp
1/0/1/1/0/4/1.0x6.0x0 eslpt
1/0/1/1/0/4/1.6 tgt
1/0/1/1/0/4/1.6.0 sdisk
1/0/4/1/0/4/0.0x50060e8010037603 estp
1/0/4/1/0/4/0.0x50060e8005b26e33 estp
1/0/4/1/0/4/0.0x50060e8005b26e33.0x0 eslpt
1/0/4/1/0/4/0.0x50060e8010037603.0x0 eslpt
1/0/4/1/0/4/0.0x50060e8005b26e33.0x4000000000000000 eslpt
1/0/4/1/0/4/0.0x50060e8010037603.0x1000000000000 eslpt
1/0/4/1/0/4/0.20 fcd_fcp
1/0/4/1/0/4/0.20.121.255.0 fcd_vbus
1/0/4/1/0/4/0.20.121.255.0.0 tgt
1/0/4/1/0/4/0.20.121.255.0.0.0 sdisk
1/0/4/1/0/4/0.20.121.255.0.0.1 sdisk
1/0/4/1/0/4/0.0x50060e8005b26e33.0x4001000000000000 eslpt
1/0/4/1/0/4/0.0x50060e8005b26e33.0x4002000000000000 eslpt
1/0/4/1/0/4/0.0x50060e8005b26e33.0x4003000000000000 eslpt
1/0/4/1/0/4/0.0x50060e8005b26e33.0x4004000000000000 eslpt
1/0/4/1/0/4/0.0x50060e8005b26e33.0x4008000000000000 eslpt
1/0/4/1/0/4/0.20.123.255.0 fcd_vbus
1/0/4/1/0/4/0.20.123.255.0.0 tgt
1/0/4/1/0/4/0.20.123.255.0.0.0 sctl
1/0/4/1/0/4/0.20.123.0.0 fcd_vbus
1/0/4/1/0/4/0.20.123.0.0.0 tgt
1/0/4/1/0/4/0.20.123.0.0.0.0 sdisk
1/0/4/1/0/4/0.20.123.0.0.0.1 sdisk
1/0/4/1/0/4/0.20.123.0.0.0.2 sdisk
1/0/4/1/0/4/0.20.123.0.0.0.3 sdisk
1/0/4/1/0/4/0.20.123.0.0.0.4 sdisk
1/0/4/1/0/4/0.20.123.0.0.1 tgt
1/0/4/1/0/4/0.20.123.0.0.1.0 sdisk
64000/0xfa00/0x0 esdisk
64000/0xfa00/0x1 esdisk
64000/0xfa00/0x2 esdisk
64000/0xfa00/0x9 esctl
64000/0xfa00/0xa esdisk
64000/0xfa00/0xb esdisk
64000/0xfa00/0xc esdisk
64000/0xfa00/0xd esdisk
64000/0xfa00/0xe esdisk
64000/0xfa00/0xf esdisk
64000/0xfa00/0x10 esdisk
64000/0xfa00/0x11 esdisk
Boot device's HP-UX HW path is: 1.0.0.3.0.6.0
iether0: INITIALIZING HP AB290-60001 PCI/PCI-X 1000Base-T 2-port U320 SCSI/2-port 1000B-T Combo Adapter at hardware path 1/0/1/1/0/6/0
iether1: INITIALIZING HP AB290-60001 PCI/PCI-X 1000Base-T 2-port U320 SCSI/2-port 1000B-T Combo Adapter at hardware path 1/0/1/1/0/6/1
iether2: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 1/0/4/1/0/6/0
iether3: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 1/0/4/1/0/6/1
iether4: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 1/0/6/1/0/6/0
iether5: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 1/0/6/1/0/6/1
iether6: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 1/0/12/1/0/6/0
iether7: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 1/0/12/1/0/6/1
iether8: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 1/0/14/1/0/6/0
iether9: INITIALIZING HP AD194-60001 PCI/PCI-X 1000Base-T 2-port 4Gb FC/2-port 1000B-T Combo Adapter at hardware path 1/0/14/1/0/6/1

System Console is on the Built-In Serial Interface
AF_INET socket/streams output daemon running, pid 72
afinet_prelink: module installed
Starting the STREAMS daemons-phase 1
LVM: Root VG activated
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 16777216
Dump device table: (start & size given in 1-Kbyte blocks)
entry 0000000000000000 - major is 3, minor is 0x0; start = 4643712, size = 8388544
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: B.11.31_LR FLAVOR=perf
Memory Information:
physical page size = 4096 bytes, logical page size = 65536 bytes
Physical: 25094912 Kbytes, lockable: 22209920 Kbytes, available: 22689792 Kbytes

Re: changed hostname and server hangs?

Jerry_109 — Thu, 22 Jan 2009 16:59:49 GMT

hello All,

I have opened the following case w/ HP
3604604482

Re: changed hostname and server hangs?

Dennis Handly — Fri, 23 Jan 2009 03:51:22 GMT

>/opt/java1.3/jre/bin/core: ELF-32 core file - IA64 from 'java' - received SIGSEGV
>I have opened the following case with HP 3604604482

Hmm. You have an Aries abort but a IPF core file. If this hadn't happened to me this week, I would have thought it strange. It seems Aries is broken in that it doesn't produce a PA core file.

You might be able to use "strings -a core" to see something.

Re: changed hostname and server hangs?

Jerry_109 — Fri, 23 Jan 2009 18:17:52 GMT

I stopped and restarted the /sbin/init.d/isisd with sh-x and received the following results :
###############
root@vulpolicyp[/sbin/init.d]
# sh -x ./isisd start
+ PATH=/usr/bin:/bin:/usr/sbin:/usr/bin:/usr/ccs/bin:/usr/contrib/bin:/usr/contrib/Q4/bin:/opt/perl/bin:/opt/ipf/bin:/opt
/nettladm/bin:/opt/fcms/bin:/opt/wbem/bin:/opt/wbem/sbin:/opt/sas/bin:/opt/graphics/common/bin:/opt/atok/bin:/usr/bin/X11
:/usr/contrib/bin/X11:/opt/sec_mgmt/bastille/bin:/opt/drd/bin:/opt/dsau/bin:/opt/dsau/sbin:/opt/resmon/bin:/opt/gnome/bin
:/opt/perf/bin:/usr/contrib/kwdb/bin:/opt/firefox:/opt/mozilla:/opt/prm/bin:/opt/sfm/bin:/opt/swm/bin:/opt/sec_mgmt/spc/b
in:/opt/ssh/bin:/opt/swa/bin:/opt/hpsmh/bin:/opt/langtools/bin:/opt/wlm/bin:/opt/ignite/bin:/opt/gvsd/bin:/opt/rdma/bin:/
opt/perl_32/bin:/opt/perl_64/bin:/var/opt/netscape/server7/shared/bin:/var/opt/netscape/server7/bin:/opt/spb/bin:/opt/thu
nderbird:/opt/hpvm/bin:/opt/caliper/bin:/opt/sentinel/bin:/sbin:/home/root
+ export PATH
+ mode=start
+ BASEDIR=/opt/VRTSob
+ + echo RUNNING
RUNSTATE= RUNNING
+ + echo NOT RUNNING
NORUNSTATE= NOT RUNNING
+ + echo START PENDING
STARTPENDING= START PENDING
+ + echo STOP PENDING
STOPPENDING= STOP PENDING
+ VXSVC=/opt/VRTSob/bin/vxsvc
+ KILLCMD=/opt/VRTSob/bin/vxsvc -k
+ STATUSCMD=/opt/VRTSob/bin/vxsvc -m
+ FORCESHUTDOWN=VEA Server could not be stopped after 2 minutes. VEA Server will be stopped forcefully
+ INSTANCERUNNING=An instance of vxsvc is running. Please stop it before starting another instance.
+ SHUTDOWNMESSAGE=Stopping Veritas Enterprise Administrator Service (vxsvc)
+ STARTMESSAGE=Starting Veritas Enterprise Administrator Service (vxsvc)
+ STARTSUCCESSMESSAGE=VEA Server has successfully started
+ STOPSUCCESSMESSAGE=VEA Server was shutdown successfully
+ FAILUREMESSAGE=VEA Server has failed to start
+ VXSVCNOTFOUND= /opt/VRTSob/bin/vxsvc doesn't exist
+ VEAPORTALFILE=/var/vx/isis/vea_portal
+ VXSVC_LOCK_FILE=/var/vx/isis/vxisis.lock
+ VXSVC_SHUTDOWN_LOCK_FILE=/var/vx/isis/vxisis_shutdown.lock
+ REGFILE=/etc/vx/isis/Registry
+ REGCTL=/opt/VRTSob/bin/vxregctl
+ ps -ef
+ grep -v grep
+ grep vxsvcctrl
+ 1> /dev/null
+ [ 1 -eq 0 ]
+ startService

[HP ARIES32]: ***** Log time: Fri Jan 23 09:55:29 PST 2009 *****
[HP ARIES32]:
[HP ARIES32]: Internal Error (code : 021) [PID : 19887]
[HP ARIES32]: Got masked synchronous signal 11.
[HP ARIES32]: Aborting process!!
[HP ARIES32]:
[HP ARIES32]: ARIES Version :
[HP ARIES32]: 11.31 (PHSS_37553) Ver: 3.0.00015 [May 4, 2008 23:49:23]
[HP ARIES32]: Invoked command :
[HP ARIES32]: /opt/VRTSob/bin/vxsvc -m
###############

strings -a core :
B.11.31
HP-UX
vulpolicyp
B.11.31
ia64
2066127389
java
wR!PwR!`wR!p
wgr8
-server
-client
-hotspot
-classic
-Djava.class.path=.
wv)x
wiC`
# @(#)jvm.cfg 1.13 00/05/11
# Copyright 2000 Sun Microsystems, Inc. All rights reserved.
# Copyright 2000 Sun Microsystems, Inc. Tous droits r
serv
# This software is the proprietary information of Sun Microsystems, Inc.
# Use is subject to license terms.
# List of JVMs that can be used as the first option to java, javac, etc.
# Order is important -- first in this list is the default JVM.
-server
-client
-hotspot
-classic
11:dlsym: Unknown symbol dlsetnonuniqsymflag
wz!hwz'hwQ$pwQ*(wQ1xwQ8
wz'hwx<
wQ1xwz*
wQ*(
wo~h`
wo~h
wv"X`
wv"X`
wv"X`
wv"X`