topic CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR in Operating System - HP-UX

CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

lujingxia — Thu, 14 May 2009 05:51:51 GMT

I use the following command,
SERVERHP#/:>/opt/sfm/bin/CIMUtil -e
root/cimv2 HP_ManagementProcessor
but it report ERRORS,
CIM_ERR_INVALID_CLASS: THE SPECIFIED CLASS DOES NOT EXIST.: "HP_ManagementProcessor"
below is my OE info:
SERVERHP#/:>swlist |grep OE
HPUX11i-OE-MC B.11.31 HP-UX Mission Critical Operating Environment
SERVERHP#/:>swlist |grep QPK
QPKAPPS B.11.31.0903.334a Applications Patches for HP-UX 11i v3, March 2009
QPKBASE B.11.31.0903.334a Base Quality Pack Bundle for HP-UX 11i v3, March 2009
SERVERHP#/:>

OnlineDiag B.11.31.01.03 HPUX 11.31 Support Tools Bundle, February 2007
SysFaultMgmt C.01.00.29.01 HPUX System Fault Management
need I update my OE /software?

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

Fabio Ettore — Thu, 14 May 2009 09:30:38 GMT

Hi,

read this document:

http://www.docs.hp.com/en/diag/sfm/mp_pds.pdf

and be sure to have installed WBEM on your system and other requirements as well.
Here the link where to download WBEM latest version:

http://h20392.www2.hp.com/portal/swdepot/displayProductInfo.do?productNumber=WBEMSvcs

HTH.

Best regards,
Fabio

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

Steven E. Protter — Thu, 14 May 2009 10:12:01 GMT

Shalom,

If this is an iLo equipped system and I think it is, you may have a hardware fault.

Does the card work?

SEP

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

Shinji Teragaito_1 — Fri, 15 May 2009 04:42:07 GMT

> OnlineDiag B.11.31.01.03 HPUX 11.31 Support Tools Bundle, February 2007
> SysFaultMgmt C.01.00.29.01 HPUX System Fault Management

Bottom line: you have to upgrade both of them.

They are too old :-) Both of them are the first version for 11.31.

Why don't you upgrade them ?

CIMUtil command had been provided in old SFM. But it was a tool
for HP Support Engineer. So there're none of information
available except for the usage printed when illegal option is
specified. Now it's a support tool from the latest SFM 11.31
0903 (C.05.00.06.01) as the SFM Release Notes states "SFM
introduces the CIMUtil command". Therefore you can read the man
page.

I understand the HP_ManagementProcessor class needs MP Indication
Provider (you can confirm if you have it, MPProvider, through
'cimprovider -lm SFMProviderModule') which is provided from 11.31
0709 SFM (C.02.00.04.yy) or later.

NOTE: you should not make a response center call about CIMUtil as
long as you are using the old SFM.

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

lujingxia — Mon, 18 May 2009 08:17:32 GMT

SERVERHP#/oracle/SFM:>swlist |grep 0903
FEATURE11i B.11.31.0903.334c Feature Enablement Patches for HP-UX 11i v3, March 2009
HWEnable11i B.11.31.0903.334d Hardware Enablement Patches for HP-UX 11i v3, March 2009
QPKAPPS B.11.31.0903.334a Applications Patches for HP-UX 11i v3, March 2009
QPKBASE B.11.31.0903.334a Base Quality Pack Bundle for HP-UX 11i v3, March 2009
SERVERHP#/oracle/SFM:>

I update the patch BUNDLE,but It still not update OnlineDiag and SysFaultMgmt ...
So I update PHSS_37265,PHSS_38562,PHSS_39073,
but the log says:
installed upon a previously installed base fileset. The ^â
â â specification for this base fileset is â â
â â "SFMDB.SMPGSQL-RUN,fr=C.02.00.04,v=HP". Since there is no â â
â â fileset on the target or selected from the source which â
â â matches this specification, fileset â â
â â "PHSS_37265.SMPGSQL-RUN,r=1.0" will be excluded. â â
â â NOTE: The patch fileset "PHSS_38562.GS_COREIA,r=1.0" may only be â â
â â installed upon a previously installed base fileset. The â â
â â specification for this base fileset is â â
â â "SFM-CORE.GS_COREIA,fr=C.04.00.05,v=HP". Since there is no d â â width.
â â fileset on the target or selected from the source which â â
â â matches this specification, fileset

I update the WBEMSvcs_A.02.07.04_HP-UX_B.11.31_IA_PA.depot
But it not work...
what Can I do to UPdate OnlineDiag and SysFaultMgmt ?

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

Shinji Teragaito_1 — Tue, 19 May 2009 06:47:20 GMT

Do you have 0903 OE/APPL media ? If you have, it's very simple to
upgrade your OE from 11.31 initial version to 0903 using
update-ux. Then you have almost of the software components
required for the latest OnlineDiag and SFM. Afterwards, you
should install DASProvider from the 0903 application media.

Here's the 0903 components list when I cold-installed 0903:
- openssl A.00.09.08h.040
- SysMgmtWeb A.3.0.0
- WBEMServices A.02.07.04
- EVM-EventMgr B.11.31
- SysMgmtBase B.00.02.04.05
- ProviderSvcsBase C.01.00.03.01
- SysMgmtPlus A.01.00.06
- DASProvider B.11.31.0903.01
- EventMonitoring A.04.20.31.03
- OnlineDiag B.11.31.05.06
- SysFaultMgmt C.05.00.06.01

If you don't want to upgrade your OE, you should consider to
select-install them.

If you don't have 0903 media, you have to prepare for the
prerequisites components for the latest OnlineDiag and SFM. The
installation page for the mega bundle 'DiagProdCollention' helps
you understand them:

http://h20392.www2.hp.com/portal/swdepot/displayInstallInfo.do?productNumber=DiagProdCollection

Good Luck !!

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

lujingxia — Wed, 20 May 2009 06:23:05 GMT

After I update DiagProdCollection
,It works,
Thank you .....
OnlineDiag B.11.31.05.06 HPUX 11.31 Support Tools Bundle, March 2009
SysFaultMgmt C.05.00.06.01 HPUX System Fault Management
SERVERHP#/opt/dasprovider/mof:>/opt/sfm/bin/CIMUtil -e root/cimv2 HP_ManagementProcessor
Instance 0 :

UniqueIdentifier : 0.26.75.0.7.****
ControllerType : 0
OtherControllerType :
IPAddress : 10.*.*.10
URL : http://10.*.*.10
Dedicated : 14
CreationClassName : HP_ManagementProcessor
Name : Management Processor
EnabledState : 2
OperationalStatus : 2
FirmwareRevision : 024.004.001
LEDColour : 4
LEDBlinkRate : 5
NICCondition : 6
,
But ,where can I find the value of LEDColour/EnabledState 's detail explaination ?

Thank you.....

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

Shinji Teragaito_1 — Wed, 20 May 2009 06:44:42 GMT

The data sheet for MP Instance Provider Fabio mentioned helps you
understand about EnabledState.
http://www.docs.hp.com/en/diag/sfm/mp_pds.pdf

Regarding LEDColour, please refer to
/opt/sfm/schemas/mof/HP_ManagementProcessor.mof.

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

lujingxia — Thu, 21 May 2009 06:31:19 GMT

in the cat /opt/sfm/schemas/mof/HP_ManagementProcessor.mof|more
it seems value 4 of LED color refers to unknown, but indeed it is green,
would you please tell me why?
[Description ("This is the firmware revision of the Management Processor") ]
string FirmwareRevision;

[Description ("Indicates colour of the Locator LED"),
ValueMap {"0", "1", "2", "3", "4", "5"},
Values {"Off", "Green", "Red", "Amber", "Unknown", "Not Supported"}]
uint16 LEDColour;

[Description ("Indicates blink rate of the Locator LED"),
ValueMap {"0", "1", "2", "3", "4", "5", "6"},
Values {"Steady", "Once in 2 seconds", "Once per second", "Once in half a second", "Blinking", "Unknown", "Not Support
ed"}]
uint16 LEDBlinkRate;

[Description ("Indicates NIC Status of the Management Processor"),
ValueMap {"0", "2", "3", "4", "5", "6"},
Values {"Unknown", "OK", "NIC disabled", "NIC not in operation-alternate host NIC in use, e.g. ProLiant iLO sideband o
peration", "NIC in operation but disconnected", "Failed"}]
uint16 NICCondition;

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

Shinji Teragaito_1 — Fri, 22 May 2009 03:58:48 GMT

> it seems value 4 of LED color refers to unknown, but indeed it
> is green, would you please tell me why?

Does your MP have the capability for Locator LED display ?

MP:CM> LOC

or

After accessing http://10.*.*.10 using Web Browser, does the
status summary page in the System Status tab shows the status
for Locator LED ("Turn LED On"/"Turn LED Off" button available) ?

I saw the same value 4 for LEDColour on rx7620 where MP doesn't
implement LOC command and Locator LED doesn't exist.

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

lujingxia — Mon, 25 May 2009 06:16:15 GMT

it is a SuperDome SD64 box.
But I can access it from WEB BROWSER
http://10.*.*.*
MP :Management Processor (MP) - FW Revision 024.004.001, Nov 14 2006 at 18:17:21.
Need I upgrade my firmware?

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

Shinji Teragaito_1 — Mon, 25 May 2009 08:08:15 GMT

I don't think a big/fat server such as Superdome sx2000 has a
locator LED.

Indeed I can not find any locator LED information in the
following document:

User Service Guide HP Integrity Superdome/sx2000 and
HP9000/sx2000 Servers
March 2009
http://docs.hp.com/en/A9834-9001D_ed5/A9834-9001D_ed5.pdf

Hope this helps you,

Re: CIMUtil -e root/cimv2 HP_ManagementProcessor ERROR

Shiv007 — Thu, 02 Jul 2009 07:08:44 GMT

Hi,

To Switch the LED On through iLo.

For this you may to upgrade you firmware to the latest.

You will be given a iLo interface look through web url.

http://

thanks
Shivaprasad