topic Re: ignite installation issue in Operating System - HP-UX

ignite installation issue

amitxxx — Fri, 12 Jun 2009 04:30:06 GMT

I am trying to reignite my current bl860c server and i am getting the following error while booting from ignite cd any ideas how to fix it?

Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - no room
WARNING: no swap device configured, so dump cannot be defaulted to primary swap.
WARNING: No dump devices are configured. Dump is disabled.
Starting the STREAMS daemons-phase 1
sh: pre_init_rc: not found
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: B11.23_LR FLAVOR=perf Fri Aug 29 22:35:38 PDT 2003 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 8357608 Kbytes, lockable: 6073360 Kbytes, available: 7106508 Kbytes

* Preparing to execute init...
======= 06/12/09 01:05:50 EDT HP-UX Installation Initialization. (Fri Jun 12
01:05:50 EDT 2009)
@(#)Ignite-UX Revision C.7.1.93
@(#)ignite/launch (opt) $Revision: 10.590.1.2 $ $Date: 2006/12/18
20:51:11 $
* Configuring RAM filesystems...
* SAS (Serial Attached SCSI) disk devices (LUNs) found = 1.
* No SAS disk/LUN swaps required, already in physical location order.
* Current SAS disk/LUN status:
* 0/2/1/0.0.0.0.0 0x060ed597d4d566dd.0x0
SAS:VOL060ED597D4D566DD:ENC01:BAYS01,02 "HP IR Volume "
* Scanning system for IO devices...
aCC runtime: pure virtual function called for class "".
WARNING: send_smapi_command: smapi_send_and_wait failed, got: CONTINUE
ERROR: IO action QUERY_PROCESSOR failed: got
WARNING: Could not find Q_BOOT device. Cannot determine what the boot device
was.
ERROR: Could not get io-device data (ioscan)
WARNING: send_smapi_command: smapi_send_and_wait failed, got: CONFIG_SAVE
ERROR: Could not write disk information file
NOTE: System rebooting...
Shutdown at 01:06 (in 0 minutes)
System shutdown time has arrived

Re: ignite installation issue

sujit kumar singh — Fri, 12 Jun 2009 05:38:57 GMT

Hi

Please have alook at the following thread, this shall be helpful.

1) check system firmware, upgrade if old.
2) You are telling IGnite Media, what is that ? use HP-UX Core OS and Install Media
3) What is the Drive That you are using,are yiu using a USB Drive CDROM?
4) Try assigning the Laptops CDROM , connecting to the server as Virtual Media From The Blade Enclosure ILO.

regards
sujit

Re: ignite installation issue

Steven E. Protter — Fri, 12 Jun 2009 05:44:53 GMT

Shalom,

It does appear that the source of the Ignite backup is not this machine.

Ignite has several functions for replicating machines. The least hardware dependent is Golden Image.

Taking a make_net_recovery from say ans rx3600 and laying it down on this system is likely to cause this problem due to hardware differences.

So please add a little information:

OS version
Ignite version
Source of the backup

SEP

Re: ignite installation issue

amitxxx — Fri, 12 Jun 2009 05:53:39 GMT

Hi this is blabe bl860 server, I have ignited the server a week back and everthing went fine. Today I am again tryin gto reignote it but it is throwing me the above error

I am connecting the server through vertual media and contacting it with ignite server to push the image..