topic Re: Package halt, switch, run in Operating System - HP-UX

Package halt, switch, run

wish_1 — Wed, 17 Aug 2005 05:15:40 GMT

Dear all

I have HP-UX11i rp7400 2 node cluster with 4 packages, 2 in each node.

Now the issue is i want to switch one of the package to 1 node. Please mail the correct command.

thanx n regds
wish

Re: Package halt, switch, run

Victor Fridyev — Wed, 17 Aug 2005 05:23:10 GMT

cmhaltpkg packagename
cmmodpkg -e -n nodename packagename
cmrunpkg -n nodename packagename

HTH

Re: Package halt, switch, run

wish_1 — Wed, 17 Aug 2005 06:07:56 GMT

Dear Victor Fridyev

my cmviewcl is as follows
no can you pl mail me the correct command
# cmviewcl

CLUSTER STATUS
FINESS up

NODE STATUS STATE
finess_p up running

PACKAGE STATUS STATE AUTO_RUN NODE
stars up running enabled finess_p
praxis up running enabled finess_p

NODE STATUS STATE
finess_t up running

PACKAGE STATUS STATE AUTO_RUN NODE
omni up running enabled finess_t
payroll up running enabled finess_t

t n regds
wish

Re: Package halt, switch, run

Pedro Cirne — Wed, 17 Aug 2005 06:18:56 GMT

Hi,

What package do you want to move to what node?

Enjoy :)

Pedro

Re: Package halt, switch, run

melvyn burnard — Wed, 17 Aug 2005 06:55:57 GMT

cmhaltpkg package_name
cmrunpkg -n nodename packagename
cmmodpkg -e packagename

All documented in the Managing Serviceguard manuals at:
http://docs.hp.com/en/ha

Re: Package halt, switch, run

Victor Fridyev — Wed, 17 Aug 2005 09:05:04 GMT

Hi,

In order to switch praxis from finess_p to _t; run
cmhaltpkg praxis
cmmodpkg -e -n finess_t praxis
cmrunpkg -n finess_t praxis

HTH

Re: Package halt, switch, run

Cem Tugrul — Wed, 17 Aug 2005 10:20:03 GMT

Wish,

Here is an example from my clustering;

baan01:/#cmviewcl

CLUSTER STATUS
MANCLUSTER up

NODE STATUS STATE
baan01 up running

PACKAGE STATUS STATE AUTO_RUN NODE
BAAN up running enabled baan01
OMNI up running enabled baan01

NODE STATUS STATE
baan03 down unknown

As you seen my nodes are baan01 &baan02
and my pkts are BAAN & OMNI

Do not care my node baan03 because i closed it we will change it as soon as possible

But when it was working my OMNI pkt was working on it...

Anyway,just suppose it is up and running but
no working pkgs onit;
so let's say i want to run my OMNI pkg on node baan03 so steps are;

i)baan01:/#cmhaltpkg OMNI

(waits OMNIpkthalted) and you have to see
a message OMNI pkg halted and run cmviewcl
and see the OMNI status really halted!!!!!
if OK then

ii)cmrunpkg -n baan03 OMNI
again check with cmviewcl command
so this time i have to see like;

CLUSTER STATUS
MANCLUSTER up

NODE STATUS STATE
baan01 up running

PACKAGE STATUS STATE AUTO_RUN NODE
BAAN up running enabled baan01
OMNI up running disable baan03
NODE STATUS STATE
baan03 up running

the difference on AUTO_RUN is disable for OMNI pkg on node baan03

so go to node baan03 and just write;

baan03:/#cmmodpkg -e OMNI

i think it is very clear now...

Good Luck,

Re: Package halt, switch, run

wish_1 — Thu, 18 Aug 2005 01:58:01 GMT

Hi,

Sorry I have not send the details to you but i have shifted the packages but i am facing problem to enable the packages the cmviewcl is as follows:

# cmviewcl

CLUSTER STATUS
FINESS up

NODE STATUS STATE
finess_p up running

PACKAGE STATUS STATE AUTO_RUN NODE
stars up running enabled finess_p
praxis up running enabled finess_p

NODE STATUS STATE
finess_t up running

PACKAGE STATUS STATE AUTO_RUN NODE
omni up running disabled finess_t
payroll up running disabled finess_t
#

So please mail how to set the disabled of omni & payroll to enabled

thx n regds
wish

Re: Package halt, switch, run

Cem Tugrul — Thu, 18 Aug 2005 02:18:44 GMT

Wish;

go to node finess_t
and just write;
cmmodpkg -e payroll
cmmodpkg -e omni

Good Luck,

Re: Package halt, switch, run

melvyn burnard — Thu, 18 Aug 2005 02:21:31 GMT

man cmmodpkg

Re: Package halt, switch, run

Rajesh SB — Thu, 18 Aug 2005 02:56:52 GMT

Hi,

To run a cluste package on a node.
There are 2 switches to be enabled.

1. Node switch for a package.
2. Package switch should be enabled to run the package on any node.

How to check the Node switch enabled/disabled:
Run
# cmviewcl -v |grep able
Gives output like

FMSvr up running disabled kulu

Primary up enabled kulu (current)
Alternate up enabled nagara

where,
FMSvr is the cluster package, switching is disabled.
If you want enable, run
# cmmodpkg -e FMSvr

kulu, nagara are the HA nodes.
Both the node switches are enabled.
If you want to run the package on any node this switch must be enable mode, even upon fail over.

If it is disable state, you can enable it using cmd
# cmmodpkg -e -n

Hope this helps for your problem

Cheers,
RAjesh

Re: Package halt, switch, run

wish_1 — Mon, 22 Aug 2005 01:21:48 GMT

Thank you very much to one and all